DSCover Satellite Products SCW904x manual Installation, Ensure connector key is oriented correctly

Page 6

Self Contained Wireless Alarm System v1.0

1.1 Installation:

1If required, separate the front and back covers by remov- ing the cover screw then inserting a small slotted screw driver between the front and back covers and gently twist the screwdriver to separate.

2Route Telephone line wiring, I/O Wiring, and AC power through a single or double ganged junction box and through cutout in the back cover see Fig. 2 Mounting & Wiring details. If Programming with DLS, See “4.1 Local Programming with PC-Link” on page 10. If using Template programming or Advanced Keypad programming continue to the next step.

3.Secure the back cover to the junction box with the screws provided (2 screws for single gang box or 4 screws for a double ganged box). For drywall (surface mount) secure to wall using 4 #6 3/4” wood screws and drywall plugs. See figure 2, Mounting & Wiring Details for hole locations.

If mounting unit on a double ganged box with the wall tamper feature, secure the back plate to the right side of the ganged box using the center mounting holes. This will provide the tamper switch with unobstructed access to the wall surface

4.Connect wiring to the terminals indicated. See Section 1.2 Wiring for details.

Do NOT apply power until wiring is completed.

5. Connect battery cable connector to the PC Board.

Ensure connector key is oriented correctly.

6.Position the cover onto the back plate. Ensure tamper switch is positioned for effective operation.

7.Insert cover in the lower slot at a 35° to 55° angle then snap cover in place. An audible click will be heard.

8.Apply power to System.

9.Enroll devices. Enter [ ][8][Installer Code][898]. See Section 2, Wireless Device Enrollment.

10.If performing Template programming, enter [ ][8][Installer Code][899]. See Section 3, Template Programming

11.Enter Advanced Programming if required. See Section 5, Advanced Programming.

12.Test System by violating zones and verifying successful transmission to the central station.

See DLS Programming on page 10 for reprogramming an existing Installation.

AC Power must be present for the Alarm system to answer Incoming calls from DLS

After the initial installation 24 Hrs. is required to fully charge the standby battery.

Figure 1, Opening Cover

Remove cover screw

Insert Screwdriver in slots indicated Gently pry open cover with screwdriver until cover separates

Figure 2, Mounting & Wiring Details

Mounting Holes (6) - Ganged box Mounting Holes (4) - Drywall

Wiring Access

Battery

Strain Relief

Third Hand

Tamper Switch

Cover screw hole

AC Power

12 VDC

PGM/Zones

Telephone Line

 

AC AC

+ Aux -

1 I/O 2

Ring Tip R-1

T-1

 

 

 

Red Grn Gra

Brn

2WWW.DIYALARMFORUM.COM

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Installation Guide Before Installing The Equipment Selecting a Suitable Location For The Alarm ControllerSafety Precautions required during Installation Table of Contents Page Installation & Wiring Technical SummaryInstallation Ensure connector key is oriented correctlyWiring Burglary Zone Wiring ChartMax wire Length to End-of-line Resistor Self Contained Wireless Alarm System Activate Wireless Device Wireless Device EnrollmentEnter Wireless Enrollment Mode Verify Device Electronic Serial Number ESNZone Dependant Devices Detectors Template Programming Zone Definitions Options 1Digit 3 selects 1 of the 8 following options Installer Lead-in/Lead-out and DLS Lead-in/Lead-out DLS Programming New Installations Refer to .1 Installation onExisting Installations Refer to .1 Installation on Local Programming with PC-LinkOperation Trouble Display Alarm Memory DisplayDoor Chime Enable/Disable Program User CodesAdditional Keypad Functions 7x Command Outputs 1&2Installer Programming 9User Code No-Entry ArmingAdvanced Programming Programming Work Sheets Index to Programming Work Sheets and DescriptionsFunction Key Options Programming WorksheetsFunction Key Programming Zone Definitions009 I/O Programming Installer’s Code Master CodeSystem Times Keypad Lockout OptionsFourth System Options Second System OptionsThird System Options Tenth System OptionsZone Loop Response Options Zone Attributes Options 10-13 are reserved for Future UseNo Activity Arming Pre-alert Timer PGM Output TimerCross Zone/Police Code Timer No Activity Arming TimerMiscellaneous Alarm Reporting Codes Alarm Reporting Codes, ZonesAlarm Restoral Reporting Codes, Zones Priority Alarm and Restoral Reporting CodesTamper Reporting Codes, Zones Tamper Restoral Reporting Codes, ZonesMiscellaneous Opening Disarming Reporting Codes Tamper/Restore Communicator Call Directions Communicator Format OptionsOpening/Closing Communicator Call Directions Communication Variables System Maintenance Communicator Call DirectionsSystem Test Transmissions Communicator Call Directions Test Transmission Time of DaySecond Communicator Options Third Communicator OptionsDownloading Options PGM Output Attributes Number of Rings To Answer OnInitiate PC-Link Downloading Attribute600 2-way Audio Control Options Applies to SCW9047 only Automatic Clock AdjustDelay Between Dialing Attempts First International OptionsWireless programming Wireless Zone Programming Wireless Supervisory WindowInstaller Lockout Disable General Wireless OptionsWireless Module Placement Test Installer Lockout Enable Restore Wireless Device Default ProgrammingLocal Keypad Programming Label Programming ZoneCommand Output #1 Label Fire Alarm LabelAlarm When Armed Event Message Command Output #2 LabelSecond Keypad Options Reset Programmable Labels to Factory DefaultsFirst Keypad Options Third Keypad OptionsProgramming Descriptions Keypad Function Key Programming002 Zone Definitions Master Code Installer CodeSystem Times O Programming Zones/PGMsFirst System Options Second System OptionsThird System Options Fourth System Options Tenth System OptionsOFF Keypad Always Active. The keypad does not blank Daylight Saving Time Move Clock Ahead Zone Loop Response Options134 Zone Attributes Standard Time Set Clock BackNo Activity Arm Timer PGM Output TimerCross Zone/Police Code Timer Call Waiting Cancel StringCommunicator Variables Test Transmission TimeFirst Communicator Options Third Communicator Options OFF Closing Confirmation Disabled. The keypad does not beepSecond Communicator Options First Downloading OptionsPanel Identification Code Downloading Access CodeDownloading Computer Phone Number Number of Rings to Answer OnAutomatic Clock Adjust Way Audio Control Options applies to SCW9047 onlyFollowing attributes are available for PGM Output Type First International Options Delay Between Dialing AttemptsWireless Programming Second International OptionsInstaller Lockout Disable Wireless Module Placement TestInstaller Lockout Enable Restore Wireless Device Default Programming069 Command Output Label Fire Alarm LabelsAlarm when Armed Event Message Keypad ProgrammingSecond Keypad Options OFF Power LED is disabled. Option 6 has no effectFirst Keypad Options Option Description Future UseProgrammed LCD Message Label ResetThird Keypad Options Programmed LCD Message DurationTesting & Troubleshooting Trouble 4 Failure to Communicate Trouble 8 Loss of Clock/DateAppendix a Reporting Code Formats Contact IDContact ID Zone Alarm/Restoral Event Codes SIA Format Automatic Zone Alarm/Restoral CodesAppendix B Communicator Format Options Pager Residential DialAppendix C Regulatory Approvals Information North AmericaSIA False Alarm Reduction Installations EuropeNew Zealand Appendix D SIA False Alarm Reduction Exit TimeAppendix E 2-Way Audio Verification SCW9047 only Format Reporting Code/EventHang-up Auto-detection Key Command DescriptionVOX Support Bell/Buzzer Silent During 2-Way AudioPage FCC Compliance Statement
Top Page Image Contents