DSCover Satellite Products SCW904x manual Second Communicator Options, Third Communicator Options

Page 44
SCW9047
Only
SCW9047
Only

Self Contained Wireless Alarm System v1.0

Section [381] Second Communicator Options

Option Description

[1]ON: Opening After Alarm Keypad Ringback Enabled. When the Opening After Alarm reporting code is successfully transmitted to a programmed telephone number, the keypad will sound a series of 8 beeps to confirm to the end user that the Opening After Alarm Code was sent and received. This Ringback will occur for each Opening After Alarm code successfully reported.

OFF: Opening After Alarm Keypad Ringback Disabled. Disabled

[2]Future Use

[3]ON: SIA Uses Programmed Reporting Codes. The system uses programmed reporting codes when transmitting using the SIA format.

OFF: SIA Uses Automatic Reporting Codes. The system automatically generates all reporting codes transmitted.

[4]ON: Closing Confirmation Enabled. The system beeps the keypad 8 times after successfully transmitting a Closing reporting event.

OFF: Closing Confirmation Disabled. The keypad does not beep.

[5]ON: Talk/Listen on Phone #1/3 Enabled. If Talk/Listen is requested for an event, the panel will request the session on the next

communication on Phone Number 1/3 (via L-Block) to the central station.

OFF: Talk/Listen on Phone #1/3 Disabled. The panel will not request a Talk/Listen session.

[6]ON: Talk/Listen on Phone #2 Enabled. If Talk/Listen is requested for an event, the panel will request the session on the next

communication on Phone Number 2 (via L-Block) to the central station.

OFF: Talk/Listen on Phone #2 Disabled. The panel will not request a Talk/Listen session.

[7]ON: Contact ID Uses Programmed Reporting Codes. The system uses Contact ID format programmed reporting codes when

transmitting reporting codes. OFF: Contact ID Uses Automatic Reporting Codes. The system automatically generates all reporting codes transmitted.

[8]Future Use

Section [382] Third Communicator Options

Option Description

[1]ON: Partial Closing Identifier is ‘5’. The system will use the digit [5] as the first digit of the Partial Closing reporting code when

transmitting Contact ID reporting codes. OFF: Partial Closing Identifier is ‘4’. The system will use the digit [4] as the first digit of the Partial Closing reporting code when transmitting Contact ID reporting codes.

[2]ON: Alarm Communications Enabled During Walk Test. The system will transmit all alarms during Walk Test.

OFF: Alarm Communications Disabled During Walk Test. The system will not report alarm events during Walk Test.

[3]ON: Communications Cancelled Message Enabled. The keypad will display the message ‘Communications Cancelled’ upon

successful transmission of the Communication Cancelled reporting event. OFF: Communications Cancelled Message Disabled. The keypad will not display these messages. (ON for SIA CP-01)

[4]ON: Call Waiting Cancel Enabled. The system dials the Call Waiting Cancel string on the first attempt to dial the central station.

OFF: Call Waiting Cancel Disabled. The system does not dial the Call Waiting Cancel string.

[5]-[6] Future Use

[7]ON: Residential Dialing Attempts are 1. Number of Dialing Attempts is one when using Residential Dial communication format.

OFF: Residential Dialing Attempts are 5. Residential Dial Follows Dialling Attempt counter.

[8]Future Use

Section [401] First Downloading Options

Option Description

[1]ON: Answering Machine Double Call Enabled. The system answers incoming calls for downloading (either Programmed Number

of Rings or Double Call). OFF: Answering Machine Double Call Disabled. The system does not answer incoming calls for double call attempts, but will still answer on Programmed Number of Rings.

These settings do not affect the 6 hour DLS downloading window on power up.

[2]ON: User Can Enable DLS Window. The user can enable downloading for the DLS downloading window (double call only) using the [ ][6] command.

OFF: User Can NOT Enable DLS Window. The user can not enable the DLS downloading window using the [ ][6] command.

[3]ON: Call Back Enabled. The system will hang up after a successful DLS connection and call the computer back using the DLS

Phone Number (Section [402]). OFF: Call Back Disabled. The system stays connected to the computer.

40WWW.DIYALARMFORUM.COM

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Installation Guide Safety Precautions required during Installation Before Installing The EquipmentSelecting a Suitable Location For The Alarm Controller Table of Contents Page Installation & Wiring Technical SummaryInstallation Ensure connector key is oriented correctlyMax wire Length to End-of-line Resistor WiringBurglary Zone Wiring Chart Self Contained Wireless Alarm System Wireless Device Enrollment Enter Wireless Enrollment ModeActivate Wireless Device Verify Device Electronic Serial Number ESNZone Dependant Devices Detectors Template Programming Zone Definitions Options 1Digit 3 selects 1 of the 8 following options Installer Lead-in/Lead-out and DLS Lead-in/Lead-out New Installations Refer to .1 Installation on Existing Installations Refer to .1 Installation onDLS Programming Local Programming with PC-LinkOperation Alarm Memory Display Door Chime Enable/DisableTrouble Display Program User Codes7x Command Outputs 1&2 Installer ProgrammingAdditional Keypad Functions 9User Code No-Entry ArmingAdvanced Programming Programming Work Sheets Index to Programming Work Sheets and DescriptionsProgramming Worksheets Function Key ProgrammingFunction Key Options Zone DefinitionsInstaller’s Code Master Code System Times009 I/O Programming Keypad Lockout OptionsSecond System Options Third System OptionsFourth System Options Tenth System OptionsZone Loop Response Options Zone Attributes Options 10-13 are reserved for Future UsePGM Output Timer Cross Zone/Police Code TimerNo Activity Arming Pre-alert Timer No Activity Arming TimerAlarm Reporting Codes, Zones Alarm Restoral Reporting Codes, ZonesMiscellaneous Alarm Reporting Codes Priority Alarm and Restoral Reporting CodesMiscellaneous Opening Disarming Reporting Codes Tamper Reporting Codes, ZonesTamper Restoral Reporting Codes, Zones Opening/Closing Communicator Call Directions Tamper/Restore Communicator Call DirectionsCommunicator Format Options System Maintenance Communicator Call Directions System Test Transmissions Communicator Call DirectionsCommunication Variables Test Transmission Time of DayDownloading Options Second Communicator OptionsThird Communicator Options Number of Rings To Answer On Initiate PC-Link DownloadingPGM Output Attributes AttributeAutomatic Clock Adjust Delay Between Dialing Attempts600 2-way Audio Control Options Applies to SCW9047 only First International OptionsWireless programming Wireless Zone Programming Wireless Supervisory WindowGeneral Wireless Options Wireless Module Placement Test Installer Lockout EnableInstaller Lockout Disable Restore Wireless Device Default ProgrammingLocal Keypad Programming Label Programming ZoneFire Alarm Label Alarm When Armed Event MessageCommand Output #1 Label Command Output #2 LabelReset Programmable Labels to Factory Defaults First Keypad OptionsSecond Keypad Options Third Keypad Options002 Zone Definitions Programming DescriptionsKeypad Function Key Programming Installer Code System TimesMaster Code O Programming Zones/PGMsThird System Options First System OptionsSecond System Options OFF Keypad Always Active. The keypad does not blank Fourth System OptionsTenth System Options Zone Loop Response Options 134 Zone AttributesDaylight Saving Time Move Clock Ahead Standard Time Set Clock BackPGM Output Timer Cross Zone/Police Code TimerNo Activity Arm Timer Call Waiting Cancel StringFirst Communicator Options Communicator VariablesTest Transmission Time OFF Closing Confirmation Disabled. The keypad does not beep Second Communicator OptionsThird Communicator Options First Downloading OptionsDownloading Access Code Downloading Computer Phone NumberPanel Identification Code Number of Rings to Answer OnFollowing attributes are available for PGM Output Type Automatic Clock AdjustWay Audio Control Options applies to SCW9047 only Delay Between Dialing Attempts Wireless ProgrammingFirst International Options Second International OptionsWireless Module Placement Test Installer Lockout EnableInstaller Lockout Disable Restore Wireless Device Default ProgrammingFire Alarm Labels Alarm when Armed Event Message069 Command Output Label Keypad ProgrammingOFF Power LED is disabled. Option 6 has no effect First Keypad OptionsSecond Keypad Options Option Description Future UseLabel Reset Third Keypad OptionsProgrammed LCD Message Programmed LCD Message DurationTesting & Troubleshooting Trouble 4 Failure to Communicate Trouble 8 Loss of Clock/DateAppendix a Reporting Code Formats Contact IDContact ID Zone Alarm/Restoral Event Codes SIA Format Automatic Zone Alarm/Restoral CodesAppendix B Communicator Format Options Pager Residential DialAppendix C Regulatory Approvals Information North AmericaNew Zealand SIA False Alarm Reduction InstallationsEurope Appendix D SIA False Alarm Reduction Exit TimeAppendix E 2-Way Audio Verification SCW9047 only Format Reporting Code/EventKey Command Description VOX SupportHang-up Auto-detection Bell/Buzzer Silent During 2-Way AudioPage FCC Compliance Statement
Top Page Image Contents