New Buck Corporation 20 Room Heater manual Door Gasket Replacement Cold Heater

Page 35

4. Using penetrating oil, generously lubricate the four (4) bolt threads holding the catalyst housing in place. Allow to penetrate.

5. Using a 9/16” wrench or 9/16” socket, loosen the four (4) bolts and remove the catalyst housing (drop down) and place in a suitable work area.

6. Using needle nose pliers, grasp the front edge of the stainless steel “can” which houses a catalytic element and pull upward.

7. Using a small putty knife or scraper, remove any gasket that may have adhered to the catalyst housing.

8. Now, obtain the new catalysts and wrap the stainless steel “can” with interam gasket and tape ends together using scotch tape or masking tape.

9. Insert the new catalysts into the catalytic housing and push down until they are seated on the top of the stainless steel wire mesh supports.

10. Reinstall the catalyst housing into the stove and secure in place with the bolts.

11. The stove is now ready for use.

2” X 2” X 7” STANDARD 25 CELL

CORNING LONG LIFE CATALYSTS

 

1/16” THICK INTERAM GASKET AND

 

STAINLESS STEEL CAN (2 EA.)

 

1/16” THICK INTERAM GASKET

 

(LAP ENDS 1/4” AND TAPE)

BOLT HOLES

APPLY 1/16”X 1/2” FIBERGLASS

 

GASKET COMPLETELY AROUND

 

SEALING LIP.

 

CATALYST HOUSING

 

(STEEL OR CAST IRON)

 

FRONT

DOOR GASKET REPLACEMENT (Cold Heater)

To replace deteriorated gaskets, the following steps must be taken to ensure proper installation of gaskets.

1.Obtain the proper gaskets and silicone glue from your local dealer.

2.Using pliers, remove any worn and deteriorated gaskets.

3.Using a scraper, wire brush, and sandpaper or steel wool, clean glue and gasket residue from the door frame.

4.Measure and cut gaskets to length. Care should be taken not to stretch the gaskets. What you want is a full and loose gasket weave after attachment to the framing.

5.Obtain the silicone glue and run a 3/16” bead inside the door frame.

6.Obtain the gasket (s) and place in the gasket channel areas. Use a technique which assures that the gasket is applied in a loose like manner. DO NOT STRETCH GASKETS.

7.After gasket (s) are applied to the glue, use your finger and go over all the gasket gently pressing the gasket to the channel. Use the same pressure against the gasket so that the final result is an evenly applied gasket.

8.Leave door open and allow at least one hour for the glue to dry.

ROPE GASKET

SILICONE

Image 35
Contents Page Table of Contents Page Operating Controls Room Heater FeaturesCatalyst Equipped Catalyst WarrantyAchieving Catalytic LIGHT-OFF When Refueling EPA Compliance StatusDo Not Over-fire This Heater Catalyst MonitoringMaintain Proper Draft ASH RemovalFireplace Insert Masonry Insert Installation Installation PrecautionsMaterial Required Thickness Minimum ClearancesAlternate Floor Protectors Materials Installation Preparation Required Fireplace DimensionsPossible Tools Needed for Installation Page Mounting Trim Panels Final Check Installation Precaution Residential Freestanding Room Heater InstallationFloor Protection Wall Installation Corner InstallationPreparing the Stove for Installation Tools for InstallationDetermining the Chimney Location Ceiling Exit Using Single Wall PipePreparing the Room Heater Location ChimneyFlue Exit Wall Exit Into Masonry Using Single Wall PipeWall Exit into Metal Tee-Box Ceiling Final Check Model Mobile Home Room Heater InstallationSleeping Room Wall Installation Preparing the Heater for Installation Protective PAD Outside AIR Pedestal KIT Outside AIR Duct Rain CAP PRE-FAB Fireplace Insert PRE-FAB Insert InstallationMinimum Clearances Installation Preparation Installation PrecautionsHeater Preparation Increaser Minimum Clearance to CombustiblesPage Safety Precautions Wood Heater SafetyModel 20 Operation OperationBuilding a Fire Align where handle rod exits face of air vent Type Ease Coaling Amount Wood Starting Qualities Sparks Operating and Safety HintsHelpful Hints Tips on Fire BurningCatalytic Inspection Preventive Maintenance / Parts ReplacementCleaning the Heater Catalyst Replacement Off-Season Replacement Recommended Door Gasket Replacement Cold Heater Page Contents Catalytic TroubleshootingDefinitions Possible Problems Follow New Buck TroubleshootingHeater Related Problems Problem Possible Cause SolutionProblem Possible Cause Solution CHIMNEY-RELATED Problems Problem Possible CauseProblem Possible Cause Less than Greater Inches Than COMBUSTOR-RELATED Problems Within a combustor can PI-ZC20660 Safety NoticeNEW Buck Corporation This is not a FireplaceDescription Residential Installations Parts RequirementsInstallation Precautions Listed NEW Buck Corp Model Part DescriptionCeiling Selecting a Chimney Installation and LocationThrough Ceiling Through Cathedral Framing Construction and Installation Page ZC20/Model Factors of Alternate Materials Alternate Floor Protectors MaterialsTOP Front Trim Panel Parts Requirements Mobile Home InstallationsCorner Interior Location Rain CAP Storm MAX Factors of Alternate Materials Cleaning the Unit CREOSOTE-FORMATION and Need for Removal Preventive Maintenance Safety Precautions ChimneyChimney Cleaning NEW Buck Corporation Warranty Time PeriodsProcedure Products not Covered