Hearth and Home Technologies PALOMA-BL, PALOMA-GR Installing the Bafﬂe, Positioning the Logs

Page 37

H. Installing the Bafﬂe

The bafﬂe is shipped wrapped, inside the ﬁrebox. Install the bafﬂe with the embedded “T” side up, place it on top of the brackets on the inside of the ﬁrebox, ensuring back edge of bafﬂe makes contact with the back of the ﬁrebox.

Figure 8.17

I. Positioning the Logs

Remove the ignitor shield from the pilot assembly prior to installing the logs. (Figure 8.18).

PILOT ASSEMBLY

IGNITER SHIELD

Figure 8.18

While still breakable, the logs do not become fragile until after the appliance is burned and they have cured. After curing, any handling must be done with care as breakage can easily occur.

Note: Logs have been designed to work speciﬁcally with the burner of this appliance. Exact placement will ensure proper operation of your gas appliance.

Place log #1 into the cradle in the burner. Lean the log back towards right corner of firebox.

Figure 8.19

Locate log #2 over the pin in log #1 and into notch in log #1. Lean the log back toward the left corner of the fire- box.

PIN

Figure 8.20

Heat & Glo • Paloma • 7031-220 Rev. P • 10/08

37

Image 37

Contents What to do if you smell gas ModelsDo Discardnot Hot glass will cause burnsHomeowner Reference Information CongratulationsTable of Contents Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide DetectorsGetting Started Installation to ensure maximum safety and beneﬁtTools and Supplies Needed Selecting Appliance Location Framing and ClearancesClearances to Combustibles ModelPaloma Surround Optional Stone Surround InstalledVent Termination Minimum Clearances Termination LocationsSee .4 for speciﬁc clearances Alcove Applications Venting Components Vent InformationUse of Elbows Measuring StandardsSNKD, Horizontal Installation How to Use the Vent GraphVenting Guidelines Exception for Rear Vent KIT Snorkel Kit SLKFemale Locking Lugs Male Locking Horizontal Termination203 mm 178 mm 152 mm Vinyl Siding Vertical Termination Hole as shown in Figure Twist-lock the vent cap and seal Cathedral Ceiling Class a Metal Chimney Type a Existing Masonry ChimneyTo determine the length of flex needed, measure from Flex Liner Flex Coupler Sheet Metal Screws Slim Line Wall Thimble Installing Slim Line Trim Ring and Heat ShieldAssembling Slim Line Trim Ring and Heat Shield FIG. C Minimum Clearance Gas Information Procedure for ConversionFuel Conversions Converting to LP GasReattach Pilot Shield Verify the performance of the ignition system Gas PressuresPressure Natural Gas Propane Check for GAS Leaks Gas ConnectionConnecting to the Appliance Recommendation for WireIntelliFire Ignition System Wiring Wire Size Max. LengthLoss of Power and Battery Backup Usage Junction Box Wired to Wall Switch Wall Switch Installation for Fan OptionalRemove Shipping Materials Appliance SetupUnbolting Appliance from the Pallet Leveling and Lagging Down the Appliance AccessoriesTop to Rear Vent Conversion Installing the Vent Restrictor Shutter AdjustmentPositioning the Logs Installing the BafﬂeMineral Wool Installation precautionsOptional Blower Black Wires Recommended operating procedures Variable Installing flame control solenoid Remote ControlsRemote receiver RED Orange Blue Wiring the flame control solenoidInner Glass Door Assembly Replacement Front Door Glass Assembly InstallationBefore Lighting Appliance Operating InstructionsControls On position. The ON/OFF switch may Turn off all electric power to the applianceLighting Appliance IPI Ignition Final inspection byInitial Break-in Procedure Frequently Asked QuestionsAfter Appliance is Lit Symptom Possible Cause Corrective Action TroubleshootingIntelliﬁre Ignition System ﬂame has been lit, ﬂame Maintaining and Servicing Appliance Inspect Maintenance Tasks Maintenance TasksReference Materials Appliance Dimension Diagram Without Stone SurroundHearth Pad Location Inches MillimeterAppliance Dimensions with Stone Surround Appliance Dimension Diagram With Stone SurroundSLP Series Vent Components Vent Components DiagramMiscellaneous Vent Components ListService Parts Log Set AssemblyStocked Service Parts ListAt Depot Description Comments Part NumberStocked Paloma Bottom Plate AssemblyCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information