Hearth and Home Technologies PALOMA-BZ Leveling and Lagging Down the Appliance, Accessories

Page 34

C. Leveling and Lagging Down the Appliance

Lagging the appliance down is REQUIRED.

WARNING

Fire Risk.

Odor Risk.

Tipping Risk

•Install gas stove on a stable, level platform/ ﬂoor strong enough to support gas stove without tipping.

•USE wood ﬂooring, ceramic tile, brick hearth or high pressure laminate ﬂooring applied

directly over the sub-ﬂooring material.

Level	Securing holes	Level
screw	Lag bolt hole	screw
	Lag bolt hole

Figure 8.4

Figure 8.5

After unbolting the appliance from the pallet, insert two 1/4 20 x 1/1/2 counterscrews.

Using pliers, adjust the counterscrews to level the appli- ance.

LAGGING

CLEARANCE

HOLE

Figure 8.6

Place the lag bolt from the component bag in the center hole in the bottom plate (lagging clearance hole). The appliance must be lagged down securely to prevent tip- ping forward.

Figure 8.7

Using pliers, adjust the counterscrews to level the appli- ance.

D. Accessories

Install approved accessories per instructions included with accessories. See Service Parts List for appropriate accessories. Refer to Section 16.

WARNING

Shock or ﬁre risk.

Use ONLY optional accessories approved for this appliance.

•Using non-listed accessories voids warranty.

•Using non-listed accessories may result in a safety hazard.

•Only Hearth & Home Technologies approved

accessories may be used safely.

34	Heat & Glo • Paloma • 7031-220 Rev. P • 10/08

Image 34

Contents Do Discardnot ModelsWhat to do if you smell gas Hot glass will cause burnsCongratulations Homeowner Reference InformationTable of Contents Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of MassachusettsGetting Started Installation to ensure maximum safety and beneﬁtTools and Supplies Needed Clearances to Combustibles Framing and ClearancesSelecting Appliance Location ModelOptional Stone Surround Installed Paloma SurroundVent Termination Minimum Clearances Termination LocationsSee .4 for speciﬁc clearances Alcove Applications Use of Elbows Vent InformationVenting Components Measuring StandardsVenting Guidelines How to Use the Vent GraphSNKD, Horizontal Installation Exception for Rear Vent KIT Snorkel Kit SLKHorizontal Termination Female Locking Lugs Male Locking203 mm 178 mm 152 mm Vinyl Siding Vertical Termination Hole as shown in Figure Twist-lock the vent cap and seal Cathedral Ceiling Class a Metal Chimney Existing Masonry Chimney Type aTo determine the length of flex needed, measure from Flex Liner Flex Coupler Sheet Metal Screws Slim Line Wall Thimble Installing Slim Line Trim Ring and Heat ShieldAssembling Slim Line Trim Ring and Heat Shield FIG. C Minimum Clearance Fuel Conversions Procedure for ConversionGas Information Converting to LP GasReattach Pilot Shield Verify the performance of the ignition system Gas PressuresPressure Natural Gas Propane Gas Connection Check for GAS LeaksIntelliFire Ignition System Wiring Recommendation for WireConnecting to the Appliance Wire Size Max. LengthLoss of Power and Battery Backup Usage Wall Switch Installation for Fan Optional Junction Box Wired to Wall SwitchRemove Shipping Materials Appliance SetupUnbolting Appliance from the Pallet Accessories Leveling and Lagging Down the ApplianceTop to Rear Vent Conversion Shutter Adjustment Installing the Vent RestrictorInstalling the Bafﬂe Positioning the LogsMineral Wool Installation precautionsOptional Blower Black Wires Recommended operating procedures Variable Installing flame control solenoid Remote ControlsRemote receiver Wiring the flame control solenoid RED Orange BlueFront Door Glass Assembly Installation Inner Glass Door Assembly ReplacementBefore Lighting Appliance Operating InstructionsControls Lighting Appliance IPI Ignition Turn off all electric power to the applianceOn position. The ON/OFF switch may Final inspection byInitial Break-in Procedure Frequently Asked QuestionsAfter Appliance is Lit Symptom Possible Cause Corrective Action TroubleshootingIntelliﬁre Ignition System ﬂame has been lit, ﬂame Maintaining and Servicing Appliance Maintenance Tasks Inspect Maintenance TasksHearth Pad Appliance Dimension Diagram Without Stone SurroundReference Materials Location Inches MillimeterAppliance Dimension Diagram With Stone Surround Appliance Dimensions with Stone SurroundVent Components Diagram SLP Series Vent ComponentsVent Components List MiscellaneousLog Set Assembly Service PartsAt Depot Service Parts ListStocked Description Comments Part NumberStocked Bottom Plate Assembly PalomaCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information