Hearth and Home Technologies PALOMA-BL, PALOMA-GR, PALOMA-BZ Service Parts List, Stocked, At Depot

Page 57

E. Service Parts List				PALOMA
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
				Stocked
parts for your appliance please provide model number and serial number. All parts listed				Stocked
in this manual may be ordered from an authorized dealer.				at Depot
ITEM	DESCRIPTION	COMMENTS	PART NUMBER
	Log Set Assembly		7031-033	Y
	Removable Top Assembly Top Vent		7031-017
1	Removable Top Assembly Rear Vent	Pre May 2008	7031-070
	Removable Top Assembly Rear Vent	Post May 2008	7031-018
		Post May 2008	7031-018
2	Grill Assembly		7031-013
3	Gasket, Adaptor		460-0610
4	Adaptor 4 inch ﬂue collar		200-2470
5	DV Adaptor		7000-162
6	Firebox Assembly		2123-004
	Glass Frame Assembly	Pre Sept 2007	7031-015
	Glass Frame Assembly	Post Sept 2007	2123-005
		Post Sept 2007	2123-005
	Latch Assembly Lower	Pre Sept 2007	7031-041	Y
	Latch Assembly Lower	Post Sept 2007	386-122A	Y
		Post Sept 2007	386-122A	Y
	Latch Assembly Upper		7003-006	Y
	Bafﬂe Support		7031-437
7	Side Assembly Left		7031-024
8	Exhaust Bafﬂe		7031-219
		Bronze	2123-028
9	Front Door Assembly	Green	2123-029
		Gray	2123-016
10	Access Door Assembly		7031-023
11	Flame Control Knob		571-531	Y
12	Firebox Bottom Assembly		7031-012
13	Bottom Plate Assembly		2123-015
14	Air Deﬂector		2123-185
15	Control Assembly		7031-027
	Control Module		593-592	Y
	Junction Box		4021-013	Y
	Power Cord		230-0670	Y
	Wire Assembly		593-590A	Y
	3V Transformer		593-593A	Y
	Battery Pack		593-594A	Y
16	Side Assembly Right		7031-020
	Back Panel Assembly Vertical		7031-021
17	Back Panel Assembly Horizontal	Pre May 2008	7031-071
	Back Panel Assembly Horizontal	Post May 2008	7031-022
		Post May 2008	7031-022
18	Cover Plate		7010-159
19	Cover Plate Gasket		7010-160
Additional service part numbers appear on following page.

Heat & Glo • Paloma • 7031-220 Rev. P • 10/08

57

Image 57

Contents What to do if you smell gas ModelsDo Discardnot Hot glass will cause burnsHomeowner Reference Information CongratulationsTable of Contents Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide DetectorsInstallation to ensure maximum safety and beneﬁt Getting StartedTools and Supplies Needed Selecting Appliance Location Framing and ClearancesClearances to Combustibles ModelPaloma Surround Optional Stone Surround InstalledTermination Locations Vent Termination Minimum ClearancesSee .4 for speciﬁc clearances Alcove Applications Venting Components Vent InformationUse of Elbows Measuring StandardsSNKD, Horizontal Installation How to Use the Vent GraphVenting Guidelines Exception for Rear Vent KIT Snorkel Kit SLKFemale Locking Lugs Male Locking Horizontal Termination203 mm 178 mm 152 mm Vinyl Siding Vertical Termination Hole as shown in Figure Twist-lock the vent cap and seal Cathedral Ceiling Class a Metal Chimney Type a Existing Masonry ChimneyTo determine the length of flex needed, measure from Flex Liner Flex Coupler Sheet Metal Screws Installing Slim Line Trim Ring and Heat Shield Slim Line Wall ThimbleAssembling Slim Line Trim Ring and Heat Shield FIG. C Minimum Clearance Gas Information Procedure for ConversionFuel Conversions Converting to LP GasReattach Pilot Shield Gas Pressures Verify the performance of the ignition systemPressure Natural Gas Propane Check for GAS Leaks Gas ConnectionConnecting to the Appliance Recommendation for WireIntelliFire Ignition System Wiring Wire Size Max. LengthLoss of Power and Battery Backup Usage Junction Box Wired to Wall Switch Wall Switch Installation for Fan OptionalAppliance Setup Remove Shipping MaterialsUnbolting Appliance from the Pallet Leveling and Lagging Down the Appliance AccessoriesTop to Rear Vent Conversion Installing the Vent Restrictor Shutter AdjustmentPositioning the Logs Installing the BafﬂeInstallation precautions Mineral WoolOptional Blower Black Wires Recommended operating procedures Variable Remote Controls Installing flame control solenoidRemote receiver RED Orange Blue Wiring the flame control solenoidInner Glass Door Assembly Replacement Front Door Glass Assembly InstallationOperating Instructions Before Lighting ApplianceControls On position. The ON/OFF switch may Turn off all electric power to the applianceLighting Appliance IPI Ignition Final inspection byFrequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Troubleshooting Symptom Possible Cause Corrective ActionIntelliﬁre Ignition System ﬂame has been lit, ﬂame Maintaining and Servicing Appliance Inspect Maintenance Tasks Maintenance TasksReference Materials Appliance Dimension Diagram Without Stone SurroundHearth Pad Location Inches MillimeterAppliance Dimensions with Stone Surround Appliance Dimension Diagram With Stone SurroundSLP Series Vent Components Vent Components DiagramMiscellaneous Vent Components ListService Parts Log Set AssemblyStocked Service Parts ListAt Depot Description Comments Part NumberStocked Paloma Bottom Plate AssemblyCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information