Hearth and Home Technologies PALOMA-GY, PALOMA-GR, PALOMA-BL, PALOMA-BZ Reattach Pilot Shield

Page 27

VALVE

RUBBER

GASKET

REGULATOR

Figure 6.2

11.Using a 3/8 in. (10 mm) nut driver or wrench, remove the NG oriﬁce and replace it with the LP oriﬁce pro- vided in this kit (see Figure 6.3).

Figure 6.3

12.Unscrew the pilot tube ﬁtting on the pilot and replace the oriﬁce spud with the one included in the conver- sion kit (see Figure 6.4).

ORIFICE SPUD

PILOT TUBE

ASSEMBLY

Figure 6.4

13.Place the round LP label on the bottom base pan. Place the propane conversion plate adjacent to the existing rating plate.

Note: The qualiﬁed service agency installing this conversion MUST enter the day, month, and year, and sign the propane conversion plate added to the appliance.

14.Reinstall the bottom plate and valve assembly into the appliance. Reinstall the six hold down screws.

15.Reconnect the inlet gas line to the valve assembly and turn on the gas line valve. Check the incoming line for leaks.

16.Reconnect the electrical power supply.

17.Reconnect the orange wire to the valve assembly. This will allow for the pilot to turn on with the control switch in the "ON" position. Check all pilot line con- nections for leaks. (See Figure 6.4)

18.Use a commercially available, non-corrosive leak check solution to test for leaks around the pilot. Be sure to rinse off all leak check solution following test- ing. See Figure 6.4 for leak check points. Extinguish the pilot.

WARNING

Shock or burn risk.

•Disconnect green wire from gas valve.

Failure to disconnect green wire could result in severe burns.

19.Reinstall the green wire on the valve.

20.Before reinstalling the burner, ensure that the shutter setting is fully open. Reattach pilot to pilot shield to burner (see Figure 6.5). Retighten the screw.

REATTACH

PILOT SHIELD

Figure 6.5

Heat & Glo • Paloma • 7031-220 Rev. P • 10/08

27

Image 27

Contents Hot glass will cause burns ModelsWhat to do if you smell gas Do DiscardnotHomeowner Reference Information CongratulationsTable of Contents Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide DetectorsInstallation to ensure maximum safety and beneﬁt Getting StartedTools and Supplies Needed Model Framing and ClearancesSelecting Appliance Location Clearances to CombustiblesPaloma Surround Optional Stone Surround InstalledTermination Locations Vent Termination Minimum ClearancesSee .4 for speciﬁc clearances Alcove Applications Measuring Standards Vent InformationVenting Components Use of ElbowsException for Rear Vent KIT Snorkel Kit SLK How to Use the Vent GraphSNKD, Horizontal Installation Venting GuidelinesFemale Locking Lugs Male Locking Horizontal Termination203 mm 178 mm 152 mm Vinyl Siding Vertical Termination Hole as shown in Figure Twist-lock the vent cap and seal Cathedral Ceiling Class a Metal Chimney Type a Existing Masonry ChimneyTo determine the length of flex needed, measure from Flex Liner Flex Coupler Sheet Metal Screws Installing Slim Line Trim Ring and Heat Shield Slim Line Wall ThimbleAssembling Slim Line Trim Ring and Heat Shield FIG. C Minimum Clearance Converting to LP Gas Procedure for ConversionGas Information Fuel ConversionsReattach Pilot Shield Gas Pressures Verify the performance of the ignition systemPressure Natural Gas Propane Check for GAS Leaks Gas ConnectionWire Size Max. Length Recommendation for WireConnecting to the Appliance IntelliFire Ignition System WiringLoss of Power and Battery Backup Usage Junction Box Wired to Wall Switch Wall Switch Installation for Fan OptionalAppliance Setup Remove Shipping MaterialsUnbolting Appliance from the Pallet Leveling and Lagging Down the Appliance AccessoriesTop to Rear Vent Conversion Installing the Vent Restrictor Shutter AdjustmentPositioning the Logs Installing the BafﬂeInstallation precautions Mineral WoolOptional Blower Black Wires Recommended operating procedures Variable Remote Controls Installing flame control solenoidRemote receiver RED Orange Blue Wiring the flame control solenoidInner Glass Door Assembly Replacement Front Door Glass Assembly InstallationOperating Instructions Before Lighting ApplianceControls Final inspection by Turn off all electric power to the applianceOn position. The ON/OFF switch may Lighting Appliance IPI IgnitionFrequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Troubleshooting Symptom Possible Cause Corrective ActionIntelliﬁre Ignition System ﬂame has been lit, ﬂame Maintaining and Servicing Appliance Inspect Maintenance Tasks Maintenance TasksLocation Inches Millimeter Appliance Dimension Diagram Without Stone SurroundReference Materials Hearth PadAppliance Dimensions with Stone Surround Appliance Dimension Diagram With Stone SurroundSLP Series Vent Components Vent Components DiagramMiscellaneous Vent Components ListService Parts Log Set AssemblyDescription Comments Part Number Service Parts ListStocked At DepotStocked Paloma Bottom Plate AssemblyCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information