Brother BAS-311F-L, BAS-326F-0, BAS-311F-0 instruction manual Installation

Page 10

 

 

 

 

 

 

 

 

 

3. INSTALLATION

 

 

 

 

 

 

 

 

 

 

 

 

 

3. INSTALLATION

 

 

 

 

 

 

 

 

 

 

 

 

CAUTION

 

 

Machine installation should only be carried out by

All cords should be secured at least 25 mm away

 

 

a qualified technician.

 

 

 

 

from any moving parts. Furthermore, do not

 

 

Contact

your

Brother

dealer

or

a qualified

excessively bend the cable or secure it too firmly

 

 

staples, otherwise there is the danger that fire or

 

 

electrician for any electrical work that may need to

 

 

electric shocks could occur.

 

 

be done.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Install the belt cover and the frame side cover to

 

 

The sewing machine head weighs more than 65 kg

 

 

the machine head and motor.

 

 

(311F-0), 70 kg (311F-L, 326F-0). The installation

 

 

 

 

 

should be carried out by two or more people.

 

If using a work table which has casters, the casters

 

 

Do not connect the power cord until installation is

should be secured in such a way so that they

 

 

cannot move.

 

 

complete, otherwise the machine may operate if

 

 

 

 

 

the foot switch is depressed by mistake, which

Be sure to wear protective goggles and gloves

 

 

could result in injury.

 

 

 

 

when handling the lubricating oil and grease, so

 

 

Be sure

to

connect the

ground. If

the

ground

that they do not get into your eyes or onto your

 

 

skin, otherwise inflammation can result.

 

 

connection

is

not secure, you

run

the

risk of

 

 

Furthermore, do not drink the oil or eat the grease

 

 

receiving a serious electric shock.

 

 

 

 

 

 

 

 

under any circumstances, as they can cause

 

 

Hold the machine head with both hands by two or

 

 

vomiting and diarrhoea.

 

 

more peple when tilting it back or returning it to its

keep the oil out of the reach of children.

 

 

original position. Furthermore, after tilting back the

 

 

 

machine head, do not push the face plate side or

 

 

 

the pulley side from above, as this could cause the

 

 

 

machine head to topple over, which may result in

 

 

 

personal injury or damage to the machine.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BAS-311F-0, 311F-L, 326F-0

3

Page 9 Page 11
Image 10
Page 9 Page 11
Contents BAS-326F-0 Safety Instructions Safety indications and their meaningsInstallation Environmental requirementsSewing CleaningMaintenace and inspection Direction of operation Frame side cover Contents Changing Special Functions Name of Major Parts Specifications BAS-311F-L *3 a BAS-326F-0 *4 aInstallation Table processing diagram PositioningInstalling the control box Installing the rubber cushions Installing the oil panInstalling the cushions Installing the switching plateInstalling the machine head Tilting the sewing machine head 1170S Connecting the ground wire Connecting the cords Installing the operation panelBAS-311F-0 Solenoid type only ORG Installing the foot switch Installing the belt coverInstalling the spool stand Installing the eye guard Installing the programmer option Installing the feed base cover supports BAS-311F-L, 326F-0 Installing the X feed base cover BAS-311F-L, 326F-0Connecting the tubes pneumatic type only When installing to the underside of the work table When installing to a beamLubrication points LubricationBAS-326F-0 Correct Operation Installing the needleSelecting the needle and thread Threading the upper thread Winding the lower thread Replacing the bobbin case and threading the thread Sewing conditions and thread tensionLower thread tension Using the Operation Panel Explanation of panel110 Using the floppy disk Compatible types of floppy diskSetting the floppy disk How to use the cleaning diskClearing the error Using the program R/W Read/Write switchIf an error message is displayed To Read a pattern to memoryUsing the Test switch Checking the sewing pattern Resuming operation from a stopping poingUsing the emergency stop switch Continuing sewing from a stopping pointAdjusting the sewing Speed control Changing the X-SCALE and Y-SCALE settingsUsing the bobbin thread counter Using production counter Using single split mode Shifting a stitch pattern Before starting sewing SewingSewing operation 1230S Lubrication Cleaning and InspectionCleaning the rotary hook Draining the oilCleaning the eye guard Cleaning the control box air inlet portCleaning the air holes of belt cover and frame side cover Checking the needleAdjusting the needle bar height Standard AdjustmentsAdjusting the needle bar lift amount Adjusting the driver needle guard Adjusting the needle clearanceAdjusting the shuttle race thread guide Adjusting the movable knife Replacing the movable and fixed knives AbcdAdjusting the presser foot Changing the presser foot lift Adjusting presser foot lift to 3 5mmAdjusting presser foot lift to 5 8 mm Standard presser foot lift is 3 mm max mmAdjusting the wiper For vertical wiper standardAdjusting the two-step work clamp lift amount BAS-311F-0 Solenoid typeBAS-326F-0 Adjusting the needle up stop position Checking the input sensor and DIP switch input Clearing all memory settings Checking the input voltageDIP Switch Panel DIP switch functionsDipswitch BAS-311F-L onlyDIP switches inside the control box DIP Switch CDipswitch Changing Special Functions and Using the Memory Switches If memo-0E is ON, the work clamp opens and closes twice Switch No When on Memo-10 Main circuit board instead of the voltage Switch No Possible Units Error Codes Can not backup data. Control PCB Turn off power and check connector P20 Gauge Parts List According to Subclasses Bobbin case assy S59221-001 LC Troubleshooting Incorrect needle and rotary hook timing Adjust the needle bar lift Amount Adjust the position Head position switch cord connection Options WP stitch device Automatic bobbin changerPlay prevention work clamp 15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561, Japan. Phone
Top Page Image Contents