Brother BAS-311F-0, BAS-326F-0, BAS-311F-L Main circuit board instead of the voltage

Page 68

11.CHANGING SPECIAL FUNCTION AND USING THE MEMORY SWITCHES Memory switches (20 - 2F)

Switch No.

When ON

 

 

memo-20

During feed test operation, jump feeding 100 stitches at a time is possible using the STEP BACK

switch.

 

memo-21

After the home position is detected and the machine moves to the sewing start position, the work

clamp rises automatically.

 

memo-22

When extended option output No. 1 is ON, the sewing machine starts automatically.

 

 

memo-23

Set to ON when the bobbin changer is being used. (This part is available by special order.)

 

 

memo-24

Feed operation is enabled even if no cassette has been set when the eject device is being used

(memo-03 is ON).

 

memo-25

The enlargement and reduction ratio settings at the operation panel are fixed at the values when

memo-25 was set to ON.

 

memo-26

Thread trimming is not carried out.

 

 

memo-27

The sewing speed setting at the operation panel is fixed at the value when memo-27 was set to ON.

 

 

memo-28

Set to ON when using the thread take-up device.

 

 

memo-29

Work clamp lifting and lower thread winding before home position detection are disabled.

 

 

memo-2A

For program numbers 1 to 15, the program number is output to the extension optional outputs 4 to 7.

 

 

memo-2b

-

 

 

memo-2c

-

 

 

memo-2d

-

 

 

memo-2E

-

 

 

memo-2F

When the input voltage is being checked, the display shows the temperature of the heat sink on the

main circuit board instead of the voltage.

 

Extended option output Use the programmer (option).

Required controls for pressing motion and automatic stacking of sewing can be implemented according to various functions of the machine.

For detail of the extended option output, please consult with your local Brother Sales Office.

BAS-311F-0, 311F-L, 326F-0

61

Page 67 Page 69
Image 68
Page 67 Page 69
Contents BAS-326F-0 Safety Instructions Safety indications and their meaningsInstallation Environmental requirementsMaintenace and inspection CleaningSewing Direction of operation Frame side cover Contents Changing Special Functions Name of Major Parts Specifications BAS-311F-L *3 a BAS-326F-0 *4 aInstallation Table processing diagram PositioningInstalling the control box Installing the rubber cushions Installing the oil panInstalling the cushions Installing the switching plateInstalling the machine head Tilting the sewing machine head 1170S Connecting the ground wire Connecting the cords Installing the operation panelBAS-311F-0 Solenoid type only ORG Installing the spool stand Installing the belt coverInstalling the foot switch Installing the eye guard Installing the programmer option Installing the feed base cover supports BAS-311F-L, 326F-0 Installing the X feed base cover BAS-311F-L, 326F-0Connecting the tubes pneumatic type only When installing to the underside of the work table When installing to a beamBAS-326F-0 LubricationLubrication points Selecting the needle and thread Installing the needleCorrect Operation Threading the upper thread Winding the lower thread Replacing the bobbin case and threading the thread Sewing conditions and thread tensionLower thread tension Using the Operation Panel Explanation of panel110 Using the floppy disk Compatible types of floppy diskSetting the floppy disk How to use the cleaning diskUsing the program R/W Read/Write switch If an error message is displayedClearing the error To Read a pattern to memoryUsing the Test switch Checking the sewing pattern Resuming operation from a stopping poingUsing the emergency stop switch Continuing sewing from a stopping pointAdjusting the sewing Speed control Changing the X-SCALE and Y-SCALE settingsUsing the bobbin thread counter Using production counter Using single split mode Shifting a stitch pattern Sewing operation SewingBefore starting sewing 1230S Cleaning and Inspection Cleaning the rotary hookLubrication Draining the oilCleaning the control box air inlet port Cleaning the air holes of belt cover and frame side coverCleaning the eye guard Checking the needleAdjusting the needle bar lift amount Standard AdjustmentsAdjusting the needle bar height Adjusting the shuttle race thread guide Adjusting the needle clearanceAdjusting the driver needle guard Adjusting the movable knife Replacing the movable and fixed knives AbcdAdjusting the presser foot Adjusting presser foot lift to 3 5mm Adjusting presser foot lift to 5 8 mmChanging the presser foot lift Standard presser foot lift is 3 mm max mmAdjusting the wiper For vertical wiper standardAdjusting the two-step work clamp lift amount BAS-311F-0 Solenoid typeBAS-326F-0 Adjusting the needle up stop position Checking the input sensor and DIP switch input Clearing all memory settings Checking the input voltageDIP Switch Panel DIP switch functionsDipswitch BAS-311F-L onlyDIP switches inside the control box DIP Switch CDipswitch Changing Special Functions and Using the Memory Switches If memo-0E is ON, the work clamp opens and closes twice Switch No When on Memo-10 Main circuit board instead of the voltage Switch No Possible Units Error Codes Can not backup data. Control PCB Turn off power and check connector P20 Gauge Parts List According to Subclasses Bobbin case assy S59221-001 LC Troubleshooting Incorrect needle and rotary hook timing Adjust the needle bar lift Amount Adjust the position Head position switch cord connection Options WP stitch device Automatic bobbin changerPlay prevention work clamp 15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561, Japan. Phone
Top Page Image Contents