Brother BAS-326F-0 Using the emergency stop switch, Continuing sewing from a stopping point

Page 39

6. USING THE OPERATION PANEL

6-5. Using the emergency stop switch

Press the emergency stop switch to immediately stop the sewing machine during actual sewing or when in the test mode.

1216S

(1)

(17)

1215S

1219S

1215S

(15)(17)

(18)

1200S

Clearing the error

1.Turn the EMERGENCY STOP switch (1) clockwise and then pull it forward to release it .

2.Press the STEP BACK (RESET) switch (17) on the operation panel. (The buzzer will stop sounding.)

3.If you do not wish to resume sewing, press the EMERGENCY STOP switch (1) once more to release it, and then press the STEP BACK (RESET) switch (17) so that the operation panel display flashes. The

sewing machine will then be ready for the next sewing operation.

*If memory sewing No. 0d is OFF, press the EMER- GENCY STOP switch (7) once more to release it.

Continuing sewing from a stopping point

If you press the EMERGENCY STOP switch after the thread breaks or the bobbin thread runs out during sewing, you can then resume swing from the point where the thread broke or ran out.

1.Press the EMERGENCY STOP switch to release it.

2.Press the STEP BACK (RESET) switch (17) to trim the thread.

3.Press the STEP BACK (RESET) switch (17) once more.

(The sewing machine will move stitch by stitch in the reverse direction while this switch is pressed.)

If the sewing machine moves back too far, press the TEST switch (15) to move it forward again. Press the TEST switch (15) again to stop the machine.

4.After you have reached the desired position, depress the starting pedal to start sewing.

32

BAS-311F-0, 311F-L, 326F-0

Image 39

Contents BAS-326F-0 Safety indications and their meanings Safety InstructionsEnvironmental requirements InstallationCleaning SewingMaintenace and inspection Direction of operation Frame side cover Contents Changing Special Functions Name of Major Parts BAS-311F-L *3 a BAS-326F-0 *4 a SpecificationsInstallation Positioning Table processing diagramInstalling the control box Installing the oil pan Installing the rubber cushionsInstalling the switching plate Installing the cushionsInstalling the machine head Tilting the sewing machine head 1170S Connecting the cords Installing the operation panel Connecting the ground wireBAS-311F-0 Solenoid type only ORG Installing the belt cover Installing the foot switchInstalling the spool stand Installing the eye guard Installing the programmer option Installing the X feed base cover BAS-311F-L, 326F-0 Installing the feed base cover supports BAS-311F-L, 326F-0Connecting the tubes pneumatic type only When installing to a beam When installing to the underside of the work tableLubrication Lubrication pointsBAS-326F-0 Installing the needle Correct OperationSelecting the needle and thread Threading the upper thread Winding the lower thread Sewing conditions and thread tension Replacing the bobbin case and threading the threadLower thread tension Explanation of panel Using the Operation Panel110 Compatible types of floppy disk Using the floppy diskHow to use the cleaning disk Setting the floppy diskTo Read a pattern to memory Using the program R/W Read/Write switchIf an error message is displayed Clearing the errorResuming operation from a stopping poing Using the Test switch Checking the sewing patternContinuing sewing from a stopping point Using the emergency stop switchChanging the X-SCALE and Y-SCALE settings Adjusting the sewing Speed controlUsing the bobbin thread counter Using production counter Using single split mode Shifting a stitch pattern Sewing Before starting sewingSewing operation 1230S Draining the oil Cleaning and InspectionCleaning the rotary hook LubricationChecking the needle Cleaning the control box air inlet portCleaning the air holes of belt cover and frame side cover Cleaning the eye guardStandard Adjustments Adjusting the needle bar heightAdjusting the needle bar lift amount Adjusting the needle clearance Adjusting the driver needle guardAdjusting the shuttle race thread guide Adjusting the movable knife Abcd Replacing the movable and fixed knivesAdjusting the presser foot Standard presser foot lift is 3 mm max mm Adjusting presser foot lift to 3 5mmAdjusting presser foot lift to 5 8 mm Changing the presser foot liftFor vertical wiper standard Adjusting the wiperBAS-311F-0 Solenoid type Adjusting the two-step work clamp lift amountBAS-326F-0 Adjusting the needle up stop position Checking the input sensor and DIP switch input Checking the input voltage Clearing all memory settingsPanel DIP switch functions DIP SwitchBAS-311F-L only DipswitchDIP Switch C DIP switches inside the control boxDipswitch Changing Special Functions and Using the Memory Switches If memo-0E is ON, the work clamp opens and closes twice Switch No When on Memo-10 Main circuit board instead of the voltage Switch No Possible Units Error Codes Can not backup data. Control PCB Turn off power and check connector P20 Gauge Parts List According to Subclasses Bobbin case assy S59221-001 LC Troubleshooting Incorrect needle and rotary hook timing Adjust the needle bar lift Amount Adjust the position Head position switch cord connection WP stitch device Automatic bobbin changer OptionsPlay prevention work clamp 15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561, Japan. Phone