Brother BAS-311F-L, BAS-326F-0 instruction manual BAS-311F-0 Solenoid type only

Page 19

3. INSTALLATION


				(14)
	(10)		(17)	(15)
	(10)
	(11)
			(16)
	(13)
	(13)			A
				A
1173S	(12)			1073Q
1173S				1073Q

(19)

(18)

1175S

6.Gently tilt back the machine head. Refer to “3-9. Tilting the sewing machine head”.

Note

Be sure to have two or more people there when tilting back the machine head and returning it to its original position.

After tilting back the machine head, do not push the face side or the pulley side from above.

7.Pass the cords (10) through the hole (11) near the hinge of the work table.

Note

If the cords are passed through the wrong hole, they may become damaged.

8.Gently return the machine head to its original position.

9.Remove the screws (12), and then open the control box cover (main P.C. board mounting plate (13)).

Note

When opening the cover, hold it securely so that it dose not fall down.

10.loosen the two screws (14), and then open the cord presser plate (15) in the direction of the white arrow and pass the cords (10) through the opening.

11.Loosen the screw (17), and then connect the ground wire (16) that is coming from the machine head as shown in the illustration.

12.Remove the screw (18), and then pass it through the terminal hole in the ground cord (19) from upper shaft motor. Then re-tighten the screw (18) so that the ground cord (19) is secured as shown in the illustration.

Note

Make sure that the ground connections are secure in order to ensure safety.

<BAS-311F-0 Solenoid type only>

(1)

(2)

(3) (1)

1424S

S1. Make hole in the beam as shown in the illustration above. (Button hole diameter is 4.2mm)

S2. Install the ground wire (1) (accessory) to the beam with a tapping screw (2) (accessory).

S3. Loosen the screw (3), and then connect the ground wire (1) that is coming from the beam as shown in the illustration.

12

BAS-311F-0, 311F-L, 326F-0

Image 19

Contents BAS-326F-0 Safety indications and their meanings Safety InstructionsEnvironmental requirements InstallationSewing CleaningMaintenace and inspection Direction of operation Frame side cover Contents Changing Special Functions Name of Major Parts BAS-311F-L *3 a BAS-326F-0 *4 a SpecificationsInstallation Positioning Table processing diagramInstalling the control box Installing the oil pan Installing the rubber cushionsInstalling the switching plate Installing the cushionsInstalling the machine head Tilting the sewing machine head 1170S Connecting the cords Installing the operation panel Connecting the ground wireBAS-311F-0 Solenoid type only ORG Installing the foot switch Installing the belt coverInstalling the spool stand Installing the eye guard Installing the programmer option Installing the X feed base cover BAS-311F-L, 326F-0 Installing the feed base cover supports BAS-311F-L, 326F-0Connecting the tubes pneumatic type only When installing to a beam When installing to the underside of the work tableLubrication points LubricationBAS-326F-0 Correct Operation Installing the needleSelecting the needle and thread Threading the upper thread Winding the lower thread Sewing conditions and thread tension Replacing the bobbin case and threading the threadLower thread tension Explanation of panel Using the Operation Panel110 Compatible types of floppy disk Using the floppy diskHow to use the cleaning disk Setting the floppy diskTo Read a pattern to memory Using the program R/W Read/Write switchIf an error message is displayed Clearing the errorResuming operation from a stopping poing Using the Test switch Checking the sewing patternContinuing sewing from a stopping point Using the emergency stop switchChanging the X-SCALE and Y-SCALE settings Adjusting the sewing Speed controlUsing the bobbin thread counter Using production counter Using single split mode Shifting a stitch pattern Before starting sewing SewingSewing operation 1230S Draining the oil Cleaning and InspectionCleaning the rotary hook LubricationChecking the needle Cleaning the control box air inlet portCleaning the air holes of belt cover and frame side cover Cleaning the eye guardAdjusting the needle bar height Standard AdjustmentsAdjusting the needle bar lift amount Adjusting the driver needle guard Adjusting the needle clearanceAdjusting the shuttle race thread guide Adjusting the movable knife Abcd Replacing the movable and fixed knivesAdjusting the presser foot Standard presser foot lift is 3 mm max mm Adjusting presser foot lift to 3 5mmAdjusting presser foot lift to 5 8 mm Changing the presser foot liftFor vertical wiper standard Adjusting the wiperBAS-311F-0 Solenoid type Adjusting the two-step work clamp lift amountBAS-326F-0 Adjusting the needle up stop position Checking the input sensor and DIP switch input Checking the input voltage Clearing all memory settingsPanel DIP switch functions DIP SwitchBAS-311F-L only DipswitchDIP Switch C DIP switches inside the control boxDipswitch Changing Special Functions and Using the Memory Switches If memo-0E is ON, the work clamp opens and closes twice Switch No When on Memo-10 Main circuit board instead of the voltage Switch No Possible Units Error Codes Can not backup data. Control PCB Turn off power and check connector P20 Gauge Parts List According to Subclasses Bobbin case assy S59221-001 LC Troubleshooting Incorrect needle and rotary hook timing Adjust the needle bar lift Amount Adjust the position Head position switch cord connection WP stitch device Automatic bobbin changer OptionsPlay prevention work clamp 15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561, Japan. Phone