Brother BAS-326F-0, BAS-311F-L, BAS-311F-0 instruction manual Lubrication points

Page 27

4. LUBRICATION

4. LUBRICATION

CAUTION

Turn off the power switch before starting lubricating, otherwise the machine may operate if the foot switch is depressed by mistake, which could result in injury.

Be sure to wear protective goggles and gloves when handling the lubricating oil and grease, so that they do not get into your eyes or onto your skin, otherwise inflammation can result.

Furthermore, do not drink the oil or eat the grease under any circumstances, as they can cause vomiting and diarrhoea.

Keep the oil out of the reach of children.

Note 1: Fill the machine with oil when the oil level is down to about one-third full in the oil sight glass.

If oil is not added and the oil drops below this level, there is the danger that the machine may seize during operation.

Note 2: Be sure to let the machine operate for a while after adding the oil.

Note 3: If there is no more oil on the felt of the shuttle race base, problems with sewing may result, so add oil to the felt until it is slightly soaked.

Note 4: Use only specified Brother oil (Nisseki Mitsubishi Sewing Lube 10N; VG10) for the machine oil.

Lubrication points

1. Fill the arm-side oil tank with oil.

1190S

BAS-311F-0, 311F-L

BAS-326F-0

(2)	X direction sewing
	home position
(1)
1191S	1192S

2. Fill the bed-side oil tank with oil.

BAS-326F-0

When filling the bed oil tank with oil, move the presser arm (1) to the X direction sewing home position so that the oil hole in the X feed base cover L assembly (2) is aligned with the oil hole in the bed, and then fill the bed oil tank with oil.

20

BAS-311F-0, 311F-L, 326F-0

Image 27

Contents BAS-326F-0 Safety indications and their meanings Safety InstructionsEnvironmental requirements InstallationCleaning SewingMaintenace and inspection Direction of operation Frame side cover Contents Changing Special Functions Name of Major Parts BAS-311F-L *3 a BAS-326F-0 *4 a SpecificationsInstallation Positioning Table processing diagramInstalling the control box Installing the oil pan Installing the rubber cushionsInstalling the switching plate Installing the cushionsInstalling the machine head Tilting the sewing machine head 1170S Connecting the cords Installing the operation panel Connecting the ground wireBAS-311F-0 Solenoid type only ORG Installing the belt cover Installing the foot switchInstalling the spool stand Installing the eye guard Installing the programmer option Installing the X feed base cover BAS-311F-L, 326F-0 Installing the feed base cover supports BAS-311F-L, 326F-0Connecting the tubes pneumatic type only When installing to a beam When installing to the underside of the work tableLubrication Lubrication pointsBAS-326F-0 Installing the needle Correct OperationSelecting the needle and thread Threading the upper thread Winding the lower thread Sewing conditions and thread tension Replacing the bobbin case and threading the threadLower thread tension Explanation of panel Using the Operation Panel110 Compatible types of floppy disk Using the floppy diskHow to use the cleaning disk Setting the floppy diskTo Read a pattern to memory Using the program R/W Read/Write switchIf an error message is displayed Clearing the errorResuming operation from a stopping poing Using the Test switch Checking the sewing patternContinuing sewing from a stopping point Using the emergency stop switchChanging the X-SCALE and Y-SCALE settings Adjusting the sewing Speed controlUsing the bobbin thread counter Using production counter Using single split mode Shifting a stitch pattern Sewing Before starting sewingSewing operation 1230S Draining the oil Cleaning and InspectionCleaning the rotary hook LubricationChecking the needle Cleaning the control box air inlet portCleaning the air holes of belt cover and frame side cover Cleaning the eye guardStandard Adjustments Adjusting the needle bar heightAdjusting the needle bar lift amount Adjusting the needle clearance Adjusting the driver needle guardAdjusting the shuttle race thread guide Adjusting the movable knife Abcd Replacing the movable and fixed knivesAdjusting the presser foot Standard presser foot lift is 3 mm max mm Adjusting presser foot lift to 3 5mmAdjusting presser foot lift to 5 8 mm Changing the presser foot liftFor vertical wiper standard Adjusting the wiperBAS-311F-0 Solenoid type Adjusting the two-step work clamp lift amountBAS-326F-0 Adjusting the needle up stop position Checking the input sensor and DIP switch input Checking the input voltage Clearing all memory settingsPanel DIP switch functions DIP SwitchBAS-311F-L only DipswitchDIP Switch C DIP switches inside the control boxDipswitch Changing Special Functions and Using the Memory Switches If memo-0E is ON, the work clamp opens and closes twice Switch No When on Memo-10 Main circuit board instead of the voltage Switch No Possible Units Error Codes Can not backup data. Control PCB Turn off power and check connector P20 Gauge Parts List According to Subclasses Bobbin case assy S59221-001 LC Troubleshooting Incorrect needle and rotary hook timing Adjust the needle bar lift Amount Adjust the position Head position switch cord connection WP stitch device Automatic bobbin changer OptionsPlay prevention work clamp 15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561, Japan. Phone