Brother BAS-311F-L, BAS-326F-0, BAS-311F-0 instruction manual Using single split mode

Page 43

6. USING THE OPERATION PANEL

6-10. Using single split mode

By using single split mode, it is possible to change up to 100 patterns immediately.

(5)

(17)

(6) (12)

1224S	1225S	1215S

1.Move DIP switch B No. 1 to the ON position. This will activate single split mode. (Refer to "10.DIP SWITCH".)

2.Turn on the power read in the patterns which have been programmed for split sewing.

3.Press the MENU switch (6) until the SPLIT NO. indicator (11) is illuminated. "1" will then appear in the display screen

(5). Then, while pressing the STEP BACK switch (17), turn the dial (12) to change the contents appearing on the

display screen (5) in order.

(Example) If three patterns have been programmed for split sewing, the number on the display screen changes in

the following order: "1"

“2"

"3"

"1"

"2" ...

4. When the starting switch is pressed, only the pattern displayed on the display screen (5) will be sewn.

Note

As to split sewing, refer to the instruction manual of the “electronic programmable pattern tacker programmer”.

36

BAS-311F-0, 311F-L, 326F-0

Image 43

Contents BAS-326F-0 Safety indications and their meanings Safety InstructionsEnvironmental requirements InstallationSewing CleaningMaintenace and inspection Direction of operation Frame side cover Contents Changing Special Functions Name of Major Parts BAS-311F-L *3 a BAS-326F-0 *4 a SpecificationsInstallation Positioning Table processing diagramInstalling the control box Installing the oil pan Installing the rubber cushionsInstalling the switching plate Installing the cushionsInstalling the machine head Tilting the sewing machine head 1170S Connecting the cords Installing the operation panel Connecting the ground wireBAS-311F-0 Solenoid type only ORG Installing the foot switch Installing the belt coverInstalling the spool stand Installing the eye guard Installing the programmer option Installing the X feed base cover BAS-311F-L, 326F-0 Installing the feed base cover supports BAS-311F-L, 326F-0Connecting the tubes pneumatic type only When installing to a beam When installing to the underside of the work tableLubrication points LubricationBAS-326F-0 Correct Operation Installing the needleSelecting the needle and thread Threading the upper thread Winding the lower thread Sewing conditions and thread tension Replacing the bobbin case and threading the threadLower thread tension Explanation of panel Using the Operation Panel110 Compatible types of floppy disk Using the floppy diskHow to use the cleaning disk Setting the floppy diskTo Read a pattern to memory Using the program R/W Read/Write switchIf an error message is displayed Clearing the errorResuming operation from a stopping poing Using the Test switch Checking the sewing patternContinuing sewing from a stopping point Using the emergency stop switch Changing the X-SCALE and Y-SCALE settings Adjusting the sewing Speed controlUsing the bobbin thread counter Using production counter Using single split mode Shifting a stitch pattern Before starting sewing SewingSewing operation 1230S Draining the oil Cleaning and InspectionCleaning the rotary hook LubricationChecking the needle Cleaning the control box air inlet portCleaning the air holes of belt cover and frame side cover Cleaning the eye guardAdjusting the needle bar height Standard AdjustmentsAdjusting the needle bar lift amount Adjusting the driver needle guard Adjusting the needle clearanceAdjusting the shuttle race thread guide Adjusting the movable knife Abcd Replacing the movable and fixed knivesAdjusting the presser foot Standard presser foot lift is 3 mm max mm Adjusting presser foot lift to 3 5mmAdjusting presser foot lift to 5 8 mm Changing the presser foot liftFor vertical wiper standard Adjusting the wiperBAS-311F-0 Solenoid type Adjusting the two-step work clamp lift amountBAS-326F-0 Adjusting the needle up stop position Checking the input sensor and DIP switch input Checking the input voltage Clearing all memory settingsPanel DIP switch functions DIP SwitchBAS-311F-L only DipswitchDIP Switch C DIP switches inside the control boxDipswitch Changing Special Functions and Using the Memory Switches If memo-0E is ON, the work clamp opens and closes twice Switch No When on Memo-10 Main circuit board instead of the voltage Switch No Possible Units Error Codes Can not backup data. Control PCB Turn off power and check connector P20 Gauge Parts List According to Subclasses Bobbin case assy S59221-001 LC Troubleshooting Incorrect needle and rotary hook timing Adjust the needle bar lift Amount Adjust the position Head position switch cord connection WP stitch device Automatic bobbin changer OptionsPlay prevention work clamp 15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561, Japan. Phone