Brother BAS-326F-0, BAS-311F-L, BAS-311F-0 instruction manual Turn off power and check connector P20

Page 72

			12. ERROR CODES



Code	Cause	Remedy

E.A0	Start switch was pressed when there was no	Read sewing data again.
	sewing available data.
E.A1	Can not detect home position. X-Y feed or	Turn off power and, check X-Y feed and connector P1.
	connection of home position sensor is incorrect.

E.c0	Motor PROM is not correctly inserted.	Turn off power and check it.
E.c1	Cooling fan (left one when viewed from front) in	Turn off power and check it.	Check fan connector.
	control box does not operate.
E.c2	Heat-sink on main PCB is overheating.	Turn off power and clean air inlet port.
E.c3	Overcurrent was detected in X pulse motor.	Turn off power and check it.
E.c4	Overcurrent was detected in Y pulse motor.	Turn off power and check it.
E.c5	Cooling fan (right one when viewed from front) in	Turn off power and check it.	Check fan connector.
	control box does not operate.

E.d0	Air pressure has dropped.	If not use detector, set OFF memory switch 1d.

E.E0	Control PROM is not correctly inserted.	Turn off power and check it.
E.E1	Main PCB detected communication error.	Turn off power and then on again.
E.E2	Panel PCB detected communication error.	Turn off power and then on again.
E.E3	Incorrect connection of cable between operation	Turn off power and check it.
	panel and control box.

E.F0	Solenoid is short-circuited (malfunction of main	Turn off power and check it.
	circuit board) or power supply relay is not operating
	(malfunction of power supply circuit board).
E.F1	Incorrect connection of cable between power supply	Turn off power and check connector P20.
	PCB and main PCB.
E.F2	Over current at power supply PCB.	Turn off power and check it.

REFERENCE segment LED alphabet

Panel display

Text display

A

B

C

D

E

F

6

H

L

O

BAS-311F-0, 311F-L, 326F-0

65

Image 72

Contents BAS-326F-0 Safety Instructions Safety indications and their meaningsInstallation Environmental requirementsCleaning SewingMaintenace and inspection Direction of operation Frame side cover Contents Changing Special Functions Name of Major Parts Specifications BAS-311F-L *3 a BAS-326F-0 *4 aInstallation Table processing diagram PositioningInstalling the control box Installing the rubber cushions Installing the oil panInstalling the cushions Installing the switching plateInstalling the machine head Tilting the sewing machine head 1170S Connecting the ground wire Connecting the cords Installing the operation panelBAS-311F-0 Solenoid type only ORG Installing the belt cover Installing the foot switchInstalling the spool stand Installing the eye guard Installing the programmer option Installing the feed base cover supports BAS-311F-L, 326F-0 Installing the X feed base cover BAS-311F-L, 326F-0Connecting the tubes pneumatic type only When installing to the underside of the work table When installing to a beamLubrication Lubrication pointsBAS-326F-0 Installing the needle Correct OperationSelecting the needle and thread Threading the upper thread Winding the lower thread Replacing the bobbin case and threading the thread Sewing conditions and thread tensionLower thread tension Using the Operation Panel Explanation of panel110 Using the floppy disk Compatible types of floppy diskSetting the floppy disk How to use the cleaning diskUsing the program R/W Read/Write switch If an error message is displayedClearing the error To Read a pattern to memoryUsing the Test switch Checking the sewing pattern Resuming operation from a stopping poingUsing the emergency stop switch Continuing sewing from a stopping pointAdjusting the sewing Speed control Changing the X-SCALE and Y-SCALE settingsUsing the bobbin thread counter Using production counter Using single split mode Shifting a stitch pattern Sewing Before starting sewingSewing operation 1230S Cleaning and Inspection Cleaning the rotary hookLubrication Draining the oilCleaning the control box air inlet port Cleaning the air holes of belt cover and frame side coverCleaning the eye guard Checking the needleStandard Adjustments Adjusting the needle bar heightAdjusting the needle bar lift amount Adjusting the needle clearance Adjusting the driver needle guardAdjusting the shuttle race thread guide Adjusting the movable knife Replacing the movable and fixed knives AbcdAdjusting the presser foot Adjusting presser foot lift to 3 5mm Adjusting presser foot lift to 5 8 mmChanging the presser foot lift Standard presser foot lift is 3 mm max mmAdjusting the wiper For vertical wiper standardAdjusting the two-step work clamp lift amount BAS-311F-0 Solenoid typeBAS-326F-0 Adjusting the needle up stop position Checking the input sensor and DIP switch input Clearing all memory settings Checking the input voltageDIP Switch Panel DIP switch functionsDipswitch BAS-311F-L onlyDIP switches inside the control box DIP Switch CDipswitch Changing Special Functions and Using the Memory Switches If memo-0E is ON, the work clamp opens and closes twice Switch No When on Memo-10 Main circuit board instead of the voltage Switch No Possible Units Error Codes Can not backup data. Control PCB Turn off power and check connector P20 Gauge Parts List According to Subclasses Bobbin case assy S59221-001 LC Troubleshooting Incorrect needle and rotary hook timing Adjust the needle bar lift Amount Adjust the position Head position switch cord connection Options WP stitch device Automatic bobbin changerPlay prevention work clamp 15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561, Japan. Phone