Brother BAS-311F-0, BAS-326F-0, BAS-311F-L instruction manual Org

Page 20

3. INSTALLATION

(10)

(21)

(20)

Lock the cord

clamp at the top.

(13)

(12)

1176S

13.Securely connect connectors P1 to P7, P14, P18, P23 and P26 as indicated in table below.

Note

Check that the connector is facing the correct way, and then insert it firmly until it locks into place. Furthermore, lock the cord clamp at the top.

Machine head connectors

 

Connection location on

Cord clamps used

Connection location

No. of pins

Cord mark

circuit board

 

X, Y, Sewing sensor

12-pin

[1]

P1

(ORG)

None

Synchronizer

5-pin

[2]

P2

(SYNCHRO)

F

EMERGENCY STOP switch

9-pin

[3]

P3

(HEAD)

None

Solenoid valve

12-pin

[4]

P4

(VALVE)

None

(for pneumatic)

 

 

 

 

 

Solenoid

 

 

 

 

F, G

Presser foot

8-pin

[5]

P5

(SOL)

Thread trimmer

 

 

 

 

 

 

Wiper

 

 

 

 

 

Pulse motor, Y

5-pin

[6]

P6 (YPM)

F,G

Pulse motor, X

5-pin

[7]

P7

(XPM)

F, G

(blue)

 

 

 

 

 

Upper shaft motor

3-pin

None

P14 (UVM)

A, B, C, D, E

Operation panel

10-pin

[M]

P18 (PANEL)

A, B

Head position switch

3-pin

[23]

P23 (IMSW)

A, B

 

 

 

 

 

 

Machine specification select

10-pin

[26]

P26 (SELECT)

None

connector

 

 

 

 

 

14.Secure the cord bundle (10) with the cord clamp (20).

Note

Check that the cords do not get pulled when the machine head is tilted back gently.

15.Close the cord presser plate (15) in the direction of the black arrow, and secure it by tightening the screws (14).

16.Install the control box cover (main P.C. board mounting plate (13)) with the six screws (12).

Note

Check that the cords do not come into contact with the fan (21) and that they are not clamped by the cover at this time.

BAS-311F-0, 311F-L, 326F-0

13

Page 19 Page 21
Image 20
Page 19 Page 21
Contents BAS-326F-0 Safety Instructions Safety indications and their meaningsInstallation Environmental requirementsMaintenace and inspection CleaningSewing Direction of operation Frame side cover Contents Changing Special Functions Name of Major Parts Specifications BAS-311F-L *3 a BAS-326F-0 *4 aInstallation Table processing diagram PositioningInstalling the control box Installing the rubber cushions Installing the oil panInstalling the cushions Installing the switching plateInstalling the machine head Tilting the sewing machine head 1170S Connecting the ground wire Connecting the cords Installing the operation panelBAS-311F-0 Solenoid type only ORG Installing the spool stand Installing the belt coverInstalling the foot switch Installing the eye guard Installing the programmer option Installing the feed base cover supports BAS-311F-L, 326F-0 Installing the X feed base cover BAS-311F-L, 326F-0Connecting the tubes pneumatic type only When installing to the underside of the work table When installing to a beamBAS-326F-0 LubricationLubrication points Selecting the needle and thread Installing the needleCorrect Operation Threading the upper thread Winding the lower thread Replacing the bobbin case and threading the thread Sewing conditions and thread tensionLower thread tension Using the Operation Panel Explanation of panel110 Using the floppy disk Compatible types of floppy diskSetting the floppy disk How to use the cleaning diskUsing the program R/W Read/Write switch If an error message is displayedClearing the error To Read a pattern to memoryUsing the Test switch Checking the sewing pattern Resuming operation from a stopping poingUsing the emergency stop switch Continuing sewing from a stopping pointAdjusting the sewing Speed control Changing the X-SCALE and Y-SCALE settingsUsing the bobbin thread counter Using production counter Using single split mode Shifting a stitch pattern Sewing operation SewingBefore starting sewing 1230S Cleaning and Inspection Cleaning the rotary hookLubrication Draining the oilCleaning the control box air inlet port Cleaning the air holes of belt cover and frame side coverCleaning the eye guard Checking the needleAdjusting the needle bar lift amount Standard AdjustmentsAdjusting the needle bar height Adjusting the shuttle race thread guide Adjusting the needle clearanceAdjusting the driver needle guard Adjusting the movable knife Replacing the movable and fixed knives AbcdAdjusting the presser foot Adjusting presser foot lift to 3 5mm Adjusting presser foot lift to 5 8 mmChanging the presser foot lift Standard presser foot lift is 3 mm max mmAdjusting the wiper For vertical wiper standardAdjusting the two-step work clamp lift amount BAS-311F-0 Solenoid typeBAS-326F-0 Adjusting the needle up stop position Checking the input sensor and DIP switch input Clearing all memory settings Checking the input voltageDIP Switch Panel DIP switch functionsDipswitch BAS-311F-L onlyDIP switches inside the control box DIP Switch CDipswitch Changing Special Functions and Using the Memory Switches If memo-0E is ON, the work clamp opens and closes twice Switch No When on Memo-10 Main circuit board instead of the voltage Switch No Possible Units Error Codes Can not backup data. Control PCB Turn off power and check connector P20 Gauge Parts List According to Subclasses Bobbin case assy S59221-001 LC Troubleshooting Incorrect needle and rotary hook timing Adjust the needle bar lift Amount Adjust the position Head position switch cord connection Options WP stitch device Automatic bobbin changerPlay prevention work clamp 15-1, Naeshiro-cho, Mizuho-ku, Nagoya 467-8561, Japan. Phone
Top Page Image Contents