Black & Decker B1650 manual Using the Opti-Rise Function

How To Use Your Breadmaker

did when setting the clock above. While the“12”is flashing, press the “Up” or “Down” arrows to change the “12” to “8”, checking to make sure “AM” is dis- played. To set the minutes, press the TIMER button while the hour setting is flashing. If the hour setting has stopped flashing before the minutes have been set, press and hold the TIMER button. With the hour setting flashing again, immediately press the TIMER button to set the minutes. While the“00”is flashing, the minutes can be set to “30” using the “Up” or “Down” arrows.When the “30” stops flashing and the current time is displayed, the timer is set.

3 To start the delayed completion timer, press the TIMER button. The completion time will flash

briefly and be replaced by the current time in the display, and the green TIMER light will come on. If the green light does not come on, and

“13 Hr TIMER ERR ” appears on the display, you have set the TIMER for longer than the maximum

13 hour delay. To reset the TIMER hold the TIMER button until the hour setting flashes, and the time can be changed using the “Up” and “Down” arrows.

If the green light does not come on, and

“0 Hr TIMER ERR ” appears, the TIMER has been set for a delayed completion time which is shorter than the actual bake time (for example 3:50 is the bake time for Sweet Bread). Reset the TIMER for a longer delayed completion time.

4 To cancel the TIMER function, press the TIMER button and the green light will go out.

5 To check the completion time while the green TIMER light is on, press the TIMER button twice.

To check the completion time while the red light is on, press the TIMER button once.

6 When the actual breadmaking operation begins, the green “timer” light will go out, the red “on” light

will come on, and total bake time (3:50 for Sweet Bread) will appear on the display. The bake time will count down in one minute intervals.When the end of the countdown is reached, a beeping signal will sound and your bread is complete. The red light will now begin flashing to show the Breadmaker has automatically activated the 60 minute “KeepWarm” function

Using the Opti-Rise Function

Use Opti-Rise Function with larger 2 lb. (900 g) bread recipes only. This function cannot be used with the Dough/Pasta or Super Rapid Bake settings. The recipes in this book were created to give optimum

results with this breadmaker model. However occa- sionally, due perhaps to old ingredients or inaccurate measurements, your 2 lb. (900 g) loaf may not rise as high as it should. In addition to making adjustments to the recipe as indicated on page 13, using the Opti-Rise Function may help to provide better results.

Five minutes before the bake cycle begins, 12 beeps will sound and the 1st Opti-Rise light will flash, sig- nalling you to check on the height of the dough. If the dough is covering the top of the rear bread pan indent, DO NOT use the Opti-Rise Function. This will prevent the bread from baking into the breadmaker lid, as during the bake cycle the dough can “bloom” an additional 2 inches in height.

If the dough is not covering the top of the rear pan indent (see diagram below), press the Opti-Rise button. This will add 10 minutes of rise time to the countdown clock, and the 1st Opti-Rise light will stay lit.

After this 10 minutes of additional rise time, and just 2 minutes before the bake cycle begins, once again you will be signalled to check the dough height. If the dough is still not covering the top of the rear pan indent, another 10 minutes of rise time can be added by pressing the Opti-Rise button again. Only the 2nd Opti-Rise light will be lit now indicating the second additional rise period has begun. If the second Opti- Rise period is not chosen, the baking cycle will begin automatically.

To cancel the remaining rise time during either Opti-Rise period, simply press and hold the Opti-Rise button until a beep sounds. The bake cycle will then begin automatically.

11