Sears 183.91579 Installing the Casters, Installing the Guardrail, Leveling your Beer Dispenser

Page 5

Check all supplied accessories in the carton to be sure that all pieces are present and in good condition. A checklist of accessories is shown below for your reference:

1 Beer Tap Assembly Including:

1 Black Faucet Handle

1 Gasket for Beer Tap

1 Beer Line (transparent tube) attached to Beer Tap

1 Black Rubber Washer for Connection of Beer Line to Keg Tap

1 CO2 Regulator

1 CO2 Cylinder

1 Keg Tap (American Sankey Type)

1 Cleaning Kit

1 CO2 Gas Line (Red Tube)

2 Hose Clamps

1 CO2 Cylinder Retainer (with bolt and nut)

1Guardrail

1Drip Tray

4Casters

1Wrench (for casters)

4Large Phillips-Head Screws

8Small Phillips-Head Screws

2Retainer Mounting Screws

2Wire Shelves

4Support Pins

Installing the Casters

Nut

Follow the steps below to install the

 

casters.

 

1. Empty the inside of the cabinet

Wrench

completely and lay the beer dis-

Caster

penser down sideways. We rec-

 

ommend that you place a piece of cardboard or cloth underneath the cabinet to prevent dents or scratches to the cabinet.

2.Insert the casters into the holes on the bottom corners of the cabinet. Tighten each caster by turning the nut clockwise with the wrench provided.

3.Once all four casters have been tightened evenly, stand the cabinet in an upright position.

2.Place the gasket over the hole opening on the worktop and line up 4 holes with pilot holes.

3.Pass beer line with the nut at the end through the hole in the worktop until the beer tap is resting on top of the cabinet.

4.Align the holes of the beer tap flauge with the gasket and pilot holes on the worktop of cabinet. Make sure faucet faces the front.

Faucet Handle

Beer Tap Assembly

Large Philip Head

Small Phillips Head

Gasket

Beer line

Guard Rail

nut

pilot holes

5.Secure the beer tap to the cabinet with four large Phillips-Head screws.

Installing the Guardrail

Follow the steps below to install the guardrail on the worktop.

1.Place the guardrail on top of the cabinet.

2.Align all holes of the guardrail with the holes of the cabinet.

3.Secure the guardrail to the cabinet with eight small

Phillips-Head screws.

Leveling your Beer Dispenser

If you do not install the casters, you will have to level your beer dispenser.

Your beer dispenser has 4 leveling legs which are located in the front and rear corners. After properly placing your beer dispenser in its final position, you can level it.

Leveling legs can be adjusted by turning them clockwise to raise or counterclockwise to lower your beer dispenser. The beer dispenser door will close easier when the level- ing legs are extended.

Installing the Beer Tap

Follow the steps below to install the beer tap.

1.First, remove the cabinet plug located on the worktop. Firmly grasp the cabinet plug, twist and pull upward.

Note: Store this plug in a safe place as it will be required when converting the beer dispenser into a beverage cooler.

Installing the CO2 Regulator and CO2 Cylinder Follow the steps below to safely install the CO2 regulator and CO2 cylinder. You must read and understand the following procedures for CO2 cylinders before installation.

Note: Your CO2 cylinder is shipped empty to avoid any possible accidents during transportation. When you purchase the first keg of beer, have your beer distributor fill the CO2 cylinder.

1.Install the CO2 gas line tube to the regulator by attaching one end of the red tube to the hose barb connection on the CO2 regulator. Secure the tube by using one of the two self-locking plastic snap-on clamps. Use pliers to snap the clamp on tightly to ensure that there are no leaks.

4

Image 5
Contents Beer Dispenser Serial / Model Numbers Table of Contents IMPORTANT SAFETY INSTRUCTIONSElectrical Kenmore ONE Year Limited Warranty Beer Dispenser Warranty First StepsParts and Features Disclaimer of implied warranties limitation of remediesInstalling the Guardrail Installing the CastersInstalling the Beer Tap Leveling your Beer DispenserGAS Installation Limitations Important Safety Message for Draft Beer DispensingProper Air Circulation Electrical RequirementOperating Your Beer Dispenser Temperature AdjustmentsEnergy Saving Tips Door AlignmentCleaning CARE AND CLEANINGCLEANING THE OUTSIDE CLEANING THE INSIDEInstalling the Cleaning Kit Automatic DefrostingVACATION AND MOVING TIPS Power FAILURE/BEER DISPENSER FAILUREKEG Connections Tank Replacement Temperature is too warm Temperature is too coldSee Keg Connections Tank Replacement See Installing the CO2 Regulator and CO2Popping or cracking Sound when compressorComes on Bubbling or gurglingFlat Beer Cloudy BeerOff-Taste Beer Loose FoamSour Beer Wild BeerTail-End Beer Master Protection Agreements Numéros DE Série ET DE Modèle Table DES Matieres Consignes DE Sécurité ImportantesPour LE CO2 GAZ Carbonique ÉlectriqueInstallation Garantie DU Distributeur DE Bière Etapes DE L’INSTALLATIONGarantie Limitée D’UN AN Kenmore Déballage distributeur de bièreMontage des Roulettes Installation du régulateur de CO2 et de la bouteille de CO2Niveler votre Distributeur de Bière Montage du Robinet de BièreMise en perce du fût de bière baril à valve unique AvertissementCirculation de l’air Restrictions d’installationBesoins électriques Utilisation des RallongesConseils D’ECONOMIE D’ENERGIE Utilisation DE LA Fontaine Á BiéreServir LA Biére Cadrage de PorteTempérature de la Bière Comprendre le Réglage de la Commande de TemperatureBruits de Fonctionnement Normal Guide pour Servir la Bière Conseils pour tirer la bièreNettoyage DE L’INTÉRIEUR Entretien ET NettoyageNettoyage Nettoyage DE L’EXTÉRIEUR Connexions DE FUT Remplacement DE ReservoirVacances ET Demenagement Panne DE COURANT/PANNE DU Distributeur DE BiereNe fonctionne pas Le distributeur de bièreLe Distributeur de Biére Fonctionne Trop Ou TropLe compresseur est en Craquements lorsqueMarche Eau bouillanteLa bière est plate État de la bièreLa bière a un faux-goût La mousse se détacheLa bière est aigre Bière incontrôlableBière de fin de fût Contrat de protection Master Registre sus números de modelo y de serie Índice DE ContenidosNúmeros DE Serie Y Modelo Información Sobre Partes y Caracteristicas Garantía DEL Dispensador DE LA Cerveza Primeros PasosGarantía Limitada DE UN AÑO Kenmore Nivelación de su dispensador de la cerveza Instale las rueditas Siga los siguientes pasosInstalación del Grifo Instalación del regulador de CO2 y el cilindro de CO2Conecte a la Manga de Colocando el barril o tanque de cervezaRequisitos Eléctricos Importante Mensaje de PrecauciónUso de Alargues Limitaciones para la instalaciónConsejos Para Ahorrar Energía Utilizando EL DispenserAlineación De la Puerta Regulación de la temperaturaCuidado Y Limpieza LimpiezaLimpieza DEL Exterior Limpieza DEL InteriorDescongelado Automático Instalando el Kit de limpiezaConexiones DE Barril Reemplazo DEL Tanque Consejos Para LAS Vacaciones Y LAS MudanzasCortes DE Energía / Fallas EN EL Surtidor DE Cerveza Funciona El surtidor de cerveza noEl surtidor de cerveza Funciona mucho oGolpecito Es demasiado cálidaLa cerveza no sale del Cuando el compresor se Crujidos o chasquidosEnciende Sonido de burbujeo oLa puerta no cierra Olores en el surtidor deCerveza Apagado TurbiaPasada, de color Salvaje Sabor maloAgria Cola-Extremo Salvaje. continuadoCerveza Del Acuerdos Marco de Protección Your Home