Sears 183.91579 manual Important Safety Message for Draft Beer Dispensing, Proper Air Circulation

Page 7

4.Make sure the beer tap faucet is in the closed (faucet handle pointing straight back) position before connecting the Keg Tap to the beer keg. Pull the pull handle out and push down until it locks into position. Listen for the "click" of the pull handle when it shifts into the final downward position. (see fig. 4) This will open the beer and CO2 gas valves. Open shut-off valve on regulator. Turn pressure adjustment screw clockwise until

pressure gauge reads 8 psi. The keg is now tapped.

fig. 4

5.Carefully tilt the beer keg and rest the edge on the stainless steel keg floor support on the bottom of the interior cabinet. Slide the beer keg in slowly, ensuring that it is properly located. (see fig. 5) Close the door.

fig. 5

Lift Upright

Beer Keg

Keg Support

Important Safety Message for Draft Beer Dispensing

When CO2 is used for draft beer dispensing, the system must be adequately protected against excessive pressure build-up. This is accomplished by the already installed two safety devices with adequate relief capacity in the system.

Safety devices are installed in the following places:

A. On or immediately downstream from the CO2 regulator. B. On the keg coupler

Proper Air Circulation

•To assure your beer dispenser works at the maximum efficiency it was designed for, you should install it in a location where there is proper air circulation, plumbing and electrical connections.

•The following are recommended clearances around the beer dispenser:

Sides 3/4” (19mm) Back 2” (50mm)

•For proper keg cooling, DO NOT put anything in the refrigerator cabinet other than the keg. Placing ice bags, beverage cans or food in the open spaces around the keg will interfere with air circulation inside the cabinet and reduce cooling effectiveness.

Electrical Requirement

•Make sure there is a suitable power Outlet (115 volts, 60 hz) with proper grounding to power the beer dispenser.

•Avoid the use of 3-Prong adapter plugs or cutting off the grounding prong in order to accommodate a 2-prong outlet.

Use of Extension Cord

•Avoid the use of an extension cord because of potential safety hazards under certain conditions. If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot outlet that will accept the plug. The marked rating of the extension cord must be equal to or greater than the elec- trical rating of the appliance.

Installation Limitations

•Do not install your beer dispenser in any location not properly insulated or heated e.g. garage etc. Your beer dispenser was not designed to operate in surrounding temperatures below 55˚ Fahrenheit.

•Select a suitable location for the beer dispenser on a hard, even surface away from direct sunlight or heat source e.g. radiators, baseboard heaters, cooking appliances etc.

•Your beer dispenser is designed for free-standing installation only. It is not designed for built-in application.

Converting the Beer Dispenser to a Beverage Cooler Application

For your convenience, this beer dispenser can be converted to a beverage cooler application. Simply follow the steps below for a quick and easy conversion.

Note: When using as a beverage cooler, we do not recommend the use of casters, as stored items may fall off the shelves when the unit is in motion.

1.Close the main valve on the CO2 cylinder.

2.Close the connection between the beer keg and the keg tap by pulling and lifting the handle of the keg tap into an upright position.

3.Disconnect both the beer line and the CO2 gas line from the keg tap.

4.Remove the beer keg from the cabinet.

5.Disconnect the gas line from the CO2 regulator.

6.Remove the CO2 cylinder from the cabinet.

6

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Beer Dispenser Serial / Model Numbers Table of Contents IMPORTANT SAFETY INSTRUCTIONSElectrical Disclaimer of implied warranties limitation of remedies Beer Dispenser Warranty First StepsKenmore ONE Year Limited Warranty Parts and FeaturesLeveling your Beer Dispenser Installing the CastersInstalling the Guardrail Installing the Beer TapGAS Electrical Requirement Important Safety Message for Draft Beer DispensingInstallation Limitations Proper Air CirculationDoor Alignment Temperature AdjustmentsOperating Your Beer Dispenser Energy Saving TipsCleaning CARE AND CLEANINGAutomatic Defrosting CLEANING THE INSIDECLEANING THE OUTSIDE Installing the Cleaning KitKEG Connections Tank Replacement Power FAILURE/BEER DISPENSER FAILUREVACATION AND MOVING TIPS See Installing the CO2 Regulator and CO2 Temperature is too coldTemperature is too warm See Keg Connections Tank ReplacementBubbling or gurgling Sound when compressorPopping or cracking Comes onFlat Beer Cloudy BeerWild Beer Loose FoamOff-Taste Beer Sour BeerTail-End Beer Master Protection Agreements Numéros DE Série ET DE Modèle Table DES Matieres Consignes DE Sécurité ImportantesPour LE CO2 GAZ Carbonique ÉlectriqueDéballage distributeur de bière Garantie DU Distributeur DE Bière Etapes DE L’INSTALLATIONInstallation Garantie Limitée D’UN AN KenmoreMontage du Robinet de Bière Installation du régulateur de CO2 et de la bouteille de CO2Montage des Roulettes Niveler votre Distributeur de BièreMise en perce du fût de bière baril à valve unique AvertissementUtilisation des Rallonges Restrictions d’installationCirculation de l’air Besoins électriquesCadrage de Porte Utilisation DE LA Fontaine Á BiéreConseils D’ECONOMIE D’ENERGIE Servir LA BiéreGuide pour Servir la Bière Conseils pour tirer la bière Comprendre le Réglage de la Commande de TemperatureTempérature de la Bière Bruits de Fonctionnement NormalNettoyage Entretien ET NettoyageNettoyage DE L’INTÉRIEUR Panne DE COURANT/PANNE DU Distributeur DE Biere Connexions DE FUT Remplacement DE ReservoirNettoyage DE L’EXTÉRIEUR Vacances ET DemenagementFonctionne Trop Ou Trop Le distributeur de bièreNe fonctionne pas Le Distributeur de BiéreEau bouillante Craquements lorsqueLe compresseur est en MarcheLa bière est plate État de la bièreBière incontrôlable La mousse se détacheLa bière a un faux-goût La bière est aigreBière de fin de fût Contrat de protection Master Números DE Serie Y Modelo Índice DE ContenidosRegistre sus números de modelo y de serie Información Sobre Garantía Limitada DE UN AÑO Kenmore Garantía DEL Dispensador DE LA Cerveza Primeros PasosPartes y Caracteristicas Instalación del regulador de CO2 y el cilindro de CO2 Instale las rueditas Siga los siguientes pasosNivelación de su dispensador de la cerveza Instalación del GrifoConecte a la Manga de Colocando el barril o tanque de cervezaLimitaciones para la instalación Importante Mensaje de PrecauciónRequisitos Eléctricos Uso de AlarguesRegulación de la temperatura Utilizando EL DispenserConsejos Para Ahorrar Energía Alineación De la PuertaCuidado Y Limpieza LimpiezaInstalando el Kit de limpieza Limpieza DEL InteriorLimpieza DEL Exterior Descongelado AutomáticoCortes DE Energía / Fallas EN EL Surtidor DE Cerveza Consejos Para LAS Vacaciones Y LAS MudanzasConexiones DE Barril Reemplazo DEL Tanque Funciona mucho o El surtidor de cerveza noFunciona El surtidor de cervezaLa cerveza no sale del Es demasiado cálidaGolpecito Sonido de burbujeo o Crujidos o chasquidosCuando el compresor se EnciendeCerveza Olores en el surtidor deLa puerta no cierra Pasada, de color TurbiaApagado Agria Sabor maloSalvaje Cerveza Del Salvaje. continuadoCola-Extremo Acuerdos Marco de Protección Your Home
Top Page Image Contents