Makita LT-210 instruction manual Points in Operation and HOW to Stop

Page 10

POINTS IN OPERATION AND HOW TO STOP

Observe the applicable accident prevention regulations!

Starting

Move at least 3m away from the place of refuelling. Place the String trimmer on a clean piece of ground taking care that the cutting tool does not come into contact with the ground or any other objects.

Cold start

For machine with Loop Handle

– Push the I-O switch (1) in the direction shown by the arrow.

First place the machine on the ground.

Give a gentle push on the primer pump (1) repeatedly (7-10 times) until lfuel comes into the primer pump.

Push the choke button (2) to the position “

Firmly hold the clutch case by your left hand, as illustrated.

Slowly pull the starter grip until resistance is felt and continue with a smart pull.

Do not pull out the starter rope to its full extent and do not allow the starter handle to be retracted without control, but ensure that it is retracted slowly.

Repeat the starting operation until initial ignitions are heard.

When the engine starts, please open the throttle lever a little. The choke button

being automatic, it returns to original position “ ”.

Run the engine for approximately one minute at a moderate speed before applying full throttle.

Note: If the starter handle is pulled repeatedly when the choke button remains at “

” position, the engine will not start easily due to excessive

fuel intake.

 

In case of excessive fuel intake, remove the spark plug and pull the starter handle slowly to remove excess fuel. Also, dry the electrode section of the spark plug.

Caution during operation:

If the throttle lever is opened fully in a no-load operation, the engine rotation is increased to 10,000 /min or more. Never operate the engine at a higher speed than required and at an approximate speed of 6,000 - 8,000 /min.

Starting the warm engine

– As described above, except without moving the choke buttun.

10

Image 10
Contents LT-210 Symbols EnglishIntended use of the machine Safety InstructionsGeneral Instructions Personal protective equipmentRefueling MetersCutting Tools Maintenance instructionsMethod of operation First AidTechnical Data LT-210 Model LT-210LT-210 String Trimmer Designation of PartsMounting of Protector Mounting of HandleMounting of Nylon Cutter Head FUELS/REFUELING Points in Operation and HOW to Stop Checking the Idling speed Nylon Cutting HeadOperation Page Servicing Instructions Daily checkup and maintenanceCleaning of air cleaner Checking the spark plugCleaning of muffler exhaust port Suction head in the fuel tankFault location Maintenance scheduleStorage Emisson Compliance Period Obtaining Warranty Service HOW to Make a Claim Symboles FrançaisUtilisation spéciale de la machine Consignes DE SécuritéInstructions générales Équipement personnel de protectionRavitaillement MètresTête de coupe à fill Instructions de maintenanceMéthode d’utilisation Premier secourCaracteristiques Techniques LT-210 LT-210 Taille-bordures Nomenclature DES PiècesMontage DU Dispositif DE Protection Montage DE LA PoignéeMontage DE LA Tête DE Coupe À FIL CARBURANTS/RAVITAILLEMENT Démarrage à froid Consignes DE Mise EN Marche ET Arrêt DE LA MachineDémarrage Consignes de sécurité lors du fonctionnementContrôle de la vitesse de ralenti Tête DE Coupe À FIL EN NylonFonctionnement Remplacement du fil en nylon Nettoyage du filtre à air Contrôle et opérations de maintenance réguliersInstructions Relatives AUX Réparations Contôle de la bougie d’allumageTête d’aspiration dans le réservoir de carburant Nettoyage de l’orifice du pot d’échappementRemisage Plan de maintenanceLocalisation des défauts Simbolos Lista de contenidos PáginaUso recomendado de la máquina Instrucciones DE SeguridadInstrucciones generales Equipo Personal de ProtecciónReabastecimiento Instrucciones de mantenimiento Método de trabajoHerramientas de Corte Primeros AuxiliosDatos Técnicos LT-210 Denominación DE Partes LT-210 CortabordesMontaje DE LA Cabezal DE Corte DE Nylon Montaje DEL ManillarMontaje DEL Protector Para máquinas con manillar en bucleCOMBUSTIBLES/REABASTECIMIENTO Arranque Puntos Relacionados CON EL Manejo Y LA ParadaArranque en frio Cabezal DE Nylon OperaciónSustitución del cabezal de Nylon Instrucciones DE Servicio Comprobación y mantenimiento diariosPage Almacenamiento Dolmar GmbH Postfach 70 04 Hamburg Germany 6169512100 05.07