Shindaiwa T242X, 81643 Stopping the Engine, Never start the engine from the operating position

Page 10

Starting the Engine (continued)

WARNING!

The cutting attachment may rotate when the engine is started!

5.When the engine starts, slowly move the choke lever to the “OPEN” position. See Figure 18. (If the engine stops after the initial start, close the choke and restart.)

Open

Figure 18

WARNING!

Never start the engine from the operating position.

IMPORTANT!

If the engine fails to start after several attempts with the choke in the closed position, the engine may be flooded with fuel. If flooding is suspected,

move the choke lever to the open position and repeatedly pull the recoil starter to remove excess fuel and start the engine. If the engine still fails to start, refer to the troubleshooting section of this manual.

When the Engine Starts...

nAfter the engine starts, allow the engine to warm up at idle 2 or 3 minutes before operating the unit.

nAfter the engine is warm, pick

up the unit and clip on the shoulder strap if so equipped. See page 11.

nAdvancing the throttle makes the cutting attachment turn faster; releasing the throttle permits the attachment to stop turning. If the cutting attachment continues to rotate when the engine returns to idle, carburetor idle speed should be adjusted (see “Adjusting Engine Idle” below).

Stopping the Engine

OFF

251029

Figure 19

Idle the engine briefly before stopping (about 2 minutes), then slide the ignition switch to the “O” (Engine OFF) position.

Adjusting Engine Idle

 

Idle Adjusting

Figure 20

Screw

10

 

The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment.

Idle Speed Adjustment

WARNING!

The cutting attachment must NEVER rotate at engine idle! If the idle speed cannot be adjusted by the procedure described here, return the trimmer to your Shindaiwa dealer for inspection.

1.Place the trimmer on the ground, then start the engine, and then allow it to idle 2-3 minutes until warm.

2.If the attachment rotates when the engine is at idle, reduce the idle speed by turning the idle adjustment screw counter-clockwise. See Figure 20.

3.If a tachometer is available, the engine idle speed should be final adjusted to 3,000 (±250) rpm (min-1).

4.Carburetor fuel mixture adjustments are preset at factory and cannot be serviced in the field.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents SP1 FR1Safety Instructions ContentsIntroduction Properly Equipped Operator Use Good JudgmentSafety Labels Be Aware of the Working EnvironmentPrior to Assembly SpecificationsProduct Description Adjust Throttle Lever Free Play Assembly and AdjustmentsHandle Cutting Attachment Shield AssemblyTrimmer Head Sub-Shield T242X Blade T242X Mount the Blade Starting the Engine Mixing FuelFilling the Fuel Tank Examples of 501 mixing quantitiesStopping the Engine When the Engine StartsIdle Speed Adjustment Never start the engine from the operating positionShoulder Strap T242X Checking Unit ConditionCutting Grass-Units equipped with a trimmer head Brushcutter Handlebar Using a Blade T242XBlade Thrust Brushcutter Shoulder StrapDaily Maintenance General MaintenanceHour Maintenance Every 50 hours of operation 10/15-Hour MaintenanceEvery 10 to 15 hours of operation Remove and replace the filter elementEvery 135 hours of operation Shindaiwa Tornado Blade Long Term StorageBlade Sharpening Multiple-tooth Circular BladeTroubleshooting Guide Engine does not StartAdditional Problems Parts Covered Maintenance and Repair Requirements Manufacturers Warranty CoverageOWNER’S Warranty Responsibilities Obtaining Warranty ServiceFax 503 FaxPodadora T242 Podadora T242X ¡ADVERTENCIAInstrucciones de Seguridad IntroducciónDeclaraciones de Seguridad PrecauciónInstrucciones de Seguridad El Operario Debidamente Equipado Use Buen JuicioPíes Esté Alerta del Area de TrabajoEtiquetas de Seguridad Producto Descripción del ProductoEspecificaciones Antes de EnsamblarAjuste la holgura del acelerador Ensamblaje y AjustesMango Ensamblaje ¡PRECAUCIÓNDisco/Cuchilla T242X Monte la cuchilla tipo FiguraArranque del Motor Mezcla de CombustibleLlenando el Tanque de Combustible Ejemplos de cantidades de mezcla a proporción deAjuste de Marcha Mínima del Motor Arranque del Motor continuaciónParada del Motor Cuando arranca el motor…Correa de Hombro T242X Verifique la Condición de la UnidadCorte de Césped Máquinas Equipadas con Cabezal de Corte Mango tipo bicicleta para desmalezadora Usando un Disco T242XRebote de disco Correa de hombro para desmalezadoraMantenimiento Diario Mantenimiento GeneralMantenimiento Cada 10 Horas Cada 10 ó 15 horas de operación Mantenimiento Cada 10/15 HorasMantenimiento Cada 50 Horas Cada 50 horas de operaciónConsulte con su centro de servicio o Cada 135 horas MantenimientoSi nota acumulación excesiva de carbón Distribuidor autorizado ShindaiwaQue use aceite con estabilizador de combustible Almacenamiento de Largo PlazoAfilado de Discos Disco Shindaiwa TornadoGuia Diagnostico El Motor No ArrancaGuia Diagnostico continuación Problemas AdicionalesPiezas Cubiertas Esta Garantía ES Administrada PORCobertura DE LA Garantía DEL Fabricante Requisitos DE Mantenimiento Y ReparaciónNotas COUPE-BORDURE T242/T242X AvertissementMesures de sécurité Table des matièresMises en garde Mise EN GardeÉquipement complet de l’utilisateur Faire preuve de prudenceTenir compte de l’environnement de travail Étiquettes de sécuritéCaractéristiques techniques NomenclatureAvant l’assemblage Réglage du jeu du levier d’accélération Assemblage et réglagePoignée Tête de coupe Installation du déflecteur T242/ T242XAssemblage Rallonge T242XSa surface imprimée soit visible à Lame T242X Installer la lameInstaller la lame de façon à ce que ’utilisateur lorsque la débroussailleuseRemplissage du réservoir à carburant Mélange de carburantDémarrage du moteur Réglage du ralenti du moteur Démarrage du moteur suiteArrêt du moteur Lorsque le moteur démarreBretelle T242X Contrôle de l’état de l’appareilCoupe d’herbe-Appareils équipés d’une tête de coupe Guidon de débroussailleuse Utilisation d’une lame T242XRebond de lame Bretelle de débroussailleuseEntretien quotidien EntretienEntretien aux 10 heures Enlever et remplacer Entretien aux 10 à 15 heuresEntretien aux 50 heures ’élément du filtreEntretien aux 135 heures Toutes les 135 heures d’utilisationLame Shindaiwa Tornado Remisage à long termeAffûtage de la lame Lame circulaire à plusieurs dentsGuide de dépannage LE Moteur NE Démarre PASGuide de dépannage suite Autres ProblèmesPièces Prises EN Charge Étendue DE LA Garantie DU FabricantResponsabilités DU Propriétaire À L’ÉGARD DE LA Garantie LA Présente Garantie EST Gérée PAR
Top Page Image Contents