Shindaiwa 62891-94311 manual Adjusting the Chain, Chain Oiler, Filling the Oil Reservoir

Page 10

Adjusting the Chain

WARNING!

Never attempt to install, replace, or adjust the chain with the engine running.

WARNING!

The saw chain is very sharp. Wear gloves to protect your hands when handling.

CAUTION!

1.Place the pole pruner on a clean, flat sur- face. (For readjustment during operation, shut down the engine, then allow the guide bar and chain to cool before proceeding with the adjustment procedure).

2.Loosen the sprocket cover nut with a plug wrench.

4.Pull the chain by hand along the top of the guide bar several times from the engine to the bar’s tip. The chain should feel snug but still pull freely.

5.Tighten the sprocket cover nut securely while lifting the tip of the guide bar.

A loose chain can jump off the guide bar causing damage to the chain and associated equipment. Always make sure the chain is properly adjusted; check more often when you are breaking in a new chain.

IMPORTANT!

Proper chain adjustment is essential for maximum performance, long chain life, and operator safety. Always inspect chain tension before operating the pole pruner.

Sprocket Cover Nut

3.Lift the nose of the guide bar while turning the chain tensioning screw:

•Clockwise to tighten the chain.

•Counter-clockwise to loosen the chain.

Chain Tensioning

Screw

6.Inspect the chain for correct adjust- ment (more frequently with a new chain). The chain should feel snug but still pull freely.

Chain Oiler

WARNING!

Never fill the oil reservoir nor adjust the oiler with the engine running.

IMPORTANT!

The service life of the chain and guide bar is affected by the quality of the lubricant. Using superior lubricant such as Shindaiwa Bar and Chain Oil will help ensure a long service life, For cold weather operation, mix bar and chain oil with an equal part of kerosene.

Filling the Oil Reservoir

NOTE:

The oil reservoir has a capacity sufficient to provide about 40 minutes of cutting time (when set to deliver the minimum flow rate, or about as long as you’ll get from a tank of fuel).

1.Place the pole pruner on a clean, flat surface with the oil filler cap facing up. Wipe off any debris from the oil cap and from around the oil filler neck.

2.Remove the oil filler cap and fill the reservoir with bar and chain oil, then replace the cap.

Oil Filler

Cap

3.Wipe up spilled oil from the unit before restarting the pole pruner.

Adjusting Oil Flow Rate

CAUTION!

An increase in bar oil flow rate will speed oil consumption, requiring more frequent checks on the oil reservoir. To ensure sufficient lubrication, it may be necessary to check the oil level more frequently than at fuel tank refills.

The guide bar and chain are lubricated automatically by a pump that operates whenever the chain rotates. The pump is set at the factory to deliver a minimum flow rate, but it can be adjusted in the field. A temporary increase in oil flow is often desirable when cutting materials such as hardwood or wood with a lot of pitch.

Adjust the pump as follows:

1.Stop the engine and make sure the stop switch is in the OFF position.

2.Place the unit on its side with the oil reservoir up.

Oil

Reservoir

Oil Flow Adjusting Screw

3.Using a screwdriver, turn the oil flow rate adjustment screw in the desired direction.

•Clockwise to decrease lubrication.

•Counter-clockwise to increase lubrication.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents P231 Pole Pruner Contents IntroductionBeware of Kickback Safety PrecautionsKickback and Pinching Beware of pinchingOperating Precautions Operating PrecautionsProperly Equipped Operator Safety Equipment and Labels Technical Specifications Product DescriptionPowerhead Installation AssemblyPrior to assembly Connecting the Throttle CableConnect The Throttle Cable Adjusting the Throttle CableKeep the open ends of the tubes clean and free of debris Assembling tube sectionsInstalling the Chain Installing and Adjusting the Bar and ChainDisassembling the tube sections Adjust the pump as follows Adjusting the ChainAdjusting Oil Flow Rate Chain OilerMinimize the risk of fire, burns, and personal injury Mixing FuelFilling the Fuel Tank Always transport and store fuels in an approved containerStarting the Engine When the Engine StartsNever start the engine from the operating position Check and Adjust Idle Speed Adjusting the Engine IdleStopping the Engine Using the Pole Pruner Hour Maintenance General MaintenanceDaily Maintenance MufflerClean or replace fuel filter 10/15-Hour MaintenanceEvery 10 to 15 hours of operation Every 135 hours of operation, remove and clean the muffler MaintenanceMuffler maintenance Long Term StorageSharpening the Chain For consistent filing angles, use a filing guideTroubleshooting Guide What To CheckSymptom Possible Cause Emission System Warranty Statement Fax Specifications subject to change without notice P231 Podadora de Extensión Introducción Declaraciones de seguridad Índice¡ADVERTENCIA! Contragolpe y apriete Instrucciones generales de seguridadTrabaje con cuidado Guardarte de contragolpeInstrucciones de seguridad El operario debidamente equipadoPrecauciones del funcionamiento Etiquetas de seguridad Instrucciones de seguridad continuaciónRealice siempre el mantenimiento Descripción del producto EspecificacionesBarras y cadenas opcionales EnsamblarAntes de Ensamblar Conexión del cable del aceleradorAjuste el cable del acelerador Ensamblar continuaciónConecte el cable del acelerador Ensamblar de las secciones del tuboDesmontaje de las secciones del tubo Instalación y ajuste de la barra y la cadena de la sierraInstalación la cadena Llenado del depósito de aceite Adjuste la cadenaBomba de aceite Ajuste del flujo del aceiteEjemplos de cantidades de mezcla a proporción de Mezcla de combustibleLlenando el tanque de combustible ¡ADVERTENCIA! Disminuya el riesgo de incendiosNunca arranque el motor desde la posición de operación Arranque del motorCuando arranca el motor… El accesorio de cortes pudo Parada del motorAjuste de marcha mínima del motor Continuar girando cuando se para El motorEl uso de la potadora de extensión Mantenimiento diario Mantenimiento generalCada 10 horas mantenimiento Cada 10 15 horas mantenimiento Mantenimiento continuaciónCada 50 horas mantenimiento Mantenimiento del silenciador Almacenamiento de largo plazoCada 135 horas de operación, retire y limpie el silenciador Para limar en ángulos iguales, use una Rendimiento de la cadenaGuía para la lima Posible causa Guía de localización de fallasQué revisar RemedioGuía de localización de fallas continuación Qué revisar Posible causa RemedioDeclaración de Garantía del Sistema de Emisión Notas Tronçonneuse à perche P231 Les échappements du moteur Introduction Mises en gardeUnénoncéprécédédelamention De ce produit contiennent des subConsignes de sécurité Réaliser les coupes à haut régimeConsignes d’utilisation Équipement complet de l’utilisateurNe pas utiliser l’appareil sans le silencieux Consignes d’utilisation suite Étiquettes et dispositifs de sécuritéNomenclature Caractéristiques techniquesOptions du guide-chaîne et de la chaîne Avant l’assemblageMontage de la tête motorisée Raccord du câble d’accélérationRéglage du câble d’accélération Assemblage suiteRaccorder le câble d’accélération Assemblage les éléments du tubeInstallation de la chaîne Installation et réglage du guide-chaîne et de la chaîneDésassemblage des éléments Remplissage du réservoir d’huile Réglage de la chaîneHuileur de chaîne Réglage du débit d’huileMélange de carburant Remplissage du réservoir de carburantDémarrage du moteur Lorsque le moteur démarreRéglage du ralenti du moteur Arrêt du moteurVérification et réglage du ré- gime de ralenti Utilisation de la tronçonneuse Entretien aux 10 heures EntretienEntretien quotidien SilencieuxEntretien aux 10 à 15 heures Entretien suiteRemisage à long terme Entretien aux 50 heuresEntretien du pare-étincelles Enlever le capuchon de la bougieAffûtage de la chaîne Technique d’affûtage correcteGuide de dépannage SolutionPoints à contrôler Cause probable Solution Points à contrôlerGuide de dépannage suite Cause probableDéclaration de garantie du dispositif antipollution FR22 FR23 FR24

62891-94311 specifications

The Shindaiwa 62891-94311 is a premium combination of engineering and technology, designed for lawn care and landscaping professionals. This tool provides efficient and reliable performance, making it a top choice for outdoor enthusiasts and contractors alike. One of the standout features of the Shindaiwa 62891-94311 is its lightweight yet durable construction. This ensures that it delivers high performance without sacrificing user comfort, allowing operators to work for extended periods without undue fatigue.

This model is equipped with advanced engine technology that enhances fuel efficiency and reduces emissions. The 2-stroke engine not only delivers impressive power but also adheres to stringent environmental regulations. Users appreciate the reduced environmental footprint, which aligns with a growing trend towards sustainability in landscaping equipment.

Another key characteristic of the Shindaiwa 62891-94311 is its ergonomic design. The handle is designed for optimum comfort and control, reducing vibration during use, which leads to greater precision and reduces the risk of strain injuries. The combination of the lightweight structure and ergonomic grip allows for longer operational hours, ensuring that users can tackle large projects efficiently.

The product features easy-start technology, enabling quick and effortless ignition. This is particularly beneficial for professionals who need to maximize productivity on job sites. Additionally, the model includes an adjustable throttle, allowing users to easily adapt the power output according to their specific needs, whether it’s for trimming, edging, or heavy-duty cutting tasks.

Durability is another focus for the Shindaiwa 62891-94311. The materials used in its construction are engineered to withstand the rigors of outdoor use, ensuring longevity and reliability. This means that users can invest in this tool with confidence, knowing it can handle extensive workloads and still perform optimally.

In conclusion, the Shindaiwa 62891-94311 is a versatile and powerful tool that incorporates advanced technology, ergonomic design, and durability. It is an ideal choice for landscaping professionals seeking a reliable, efficient, and eco-friendly solution for their outdoor tasks. Whether trimming hedges or tackling tough underbrush, this model stands out as a preferred option in the field of outdoor power equipment.
Top Page Image Contents