Shindaiwa 62891-94311 manual 10/15-Hour Maintenance, Every 10 to 15 hours of operation

Page 16

10/15-Hour Maintenance

Every 10 to 15 hours of operation:

■Remove and clean the spark plug. Adjust the spark plug electrode gap to 0.6 mm. If the plug must be replaced, use a NGK BMR6A or equivalent spark plug of the correct heat range.

CAUTION!

Before removing the spark plug, clean the area around the plug to prevent dirt and debris from getting into the engine’s internal parts

0.6 mm

Clean the spark plug and check the

gap at the electrode.

CAUTION!

Incorrect spark plug installation can result in serious engine damage.

50-Hour Maintenance

Every 50 hours of operation (more frequently in dusty or dirty conditions):

■Remove and clean the cylinder cover and clean dirt and debris from the cylinder cooling fins.

■Remove the sprocket cover and inspect the sprocket for excessive dirt, debris, or wear. Remove the guide bar and clean out the guide bar groove. If the sprocket is excessively worn, replace it with a new one.

Inspect the

sprocket

■Lubricate the gear case. To perform this operation, first remove the gear case from the upper outer tube as follows.

•Loosen the gear case clamp bolt.

•Remove the index bolt from the gear case.

•Slide the gear case out of the tube.

■Using a lever-type grease gun, pump lithium-base grease (about 10 grams) into the grease fitting until you see old grease being purged from the gear case, this can be seen in the outer tube cavity at the input end of the gear case. Clean up excess grease, then reassemble the gear case onto the outer tube.

Gear Case Clamp

Index

Bolt

Grease Fitting

Clean or replace fuel filter

■Use a hooked wire to extract the fuel filter from inside the fuel tank. Inspect the fuel filter element for signs of contamination. Replace it with a new one if required. Before reinstalling the filter, inspect the fuel line. If you find damage or deterioration, remove the unit from service until it can be inspected by a Shindaiwa-trained service technician.

CAUTION!

Make sure you do not pierce the fuel line with the end of the hooked wire. The line is delicate and can be damaged easily.

Hooked Wire

Filter Element

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents P231 Pole Pruner Contents IntroductionSafety Precautions Kickback and PinchingBeware of Kickback Beware of pinchingOperating Precautions Operating PrecautionsProperly Equipped Operator Safety Equipment and Labels Technical Specifications Product DescriptionAssembly Prior to assemblyPowerhead Installation Connecting the Throttle CableAdjusting the Throttle Cable Keep the open ends of the tubes clean and free of debrisConnect The Throttle Cable Assembling tube sectionsInstalling the Chain Installing and Adjusting the Bar and ChainDisassembling the tube sections Adjusting the Chain Adjusting Oil Flow RateAdjust the pump as follows Chain OilerMixing Fuel Filling the Fuel TankMinimize the risk of fire, burns, and personal injury Always transport and store fuels in an approved containerStarting the Engine When the Engine StartsNever start the engine from the operating position Check and Adjust Idle Speed Adjusting the Engine IdleStopping the Engine Using the Pole Pruner General Maintenance Daily MaintenanceHour Maintenance MufflerClean or replace fuel filter 10/15-Hour MaintenanceEvery 10 to 15 hours of operation Maintenance Muffler maintenanceEvery 135 hours of operation, remove and clean the muffler Long Term StorageSharpening the Chain For consistent filing angles, use a filing guideTroubleshooting Guide What To CheckSymptom Possible Cause Emission System Warranty Statement Fax Specifications subject to change without notice P231 Podadora de Extensión Introducción Declaraciones de seguridad ÍndiceInstrucciones generales de seguridad Trabaje con cuidado¡ADVERTENCIA! Contragolpe y apriete Guardarte de contragolpeInstrucciones de seguridad El operario debidamente equipadoPrecauciones del funcionamiento Etiquetas de seguridad Instrucciones de seguridad continuaciónRealice siempre el mantenimiento Descripción del producto EspecificacionesEnsamblar Antes de EnsamblarBarras y cadenas opcionales Conexión del cable del aceleradorEnsamblar continuación Conecte el cable del aceleradorAjuste el cable del acelerador Ensamblar de las secciones del tuboDesmontaje de las secciones del tubo Instalación y ajuste de la barra y la cadena de la sierraInstalación la cadena Adjuste la cadena Bomba de aceiteLlenado del depósito de aceite Ajuste del flujo del aceiteMezcla de combustible Llenando el tanque de combustibleEjemplos de cantidades de mezcla a proporción de ¡ADVERTENCIA! Disminuya el riesgo de incendiosNunca arranque el motor desde la posición de operación Arranque del motorCuando arranca el motor… Parada del motor Ajuste de marcha mínima del motorEl accesorio de cortes pudo Continuar girando cuando se para El motorEl uso de la potadora de extensión Mantenimiento diario Mantenimiento generalCada 10 horas mantenimiento Cada 10 15 horas mantenimiento Mantenimiento continuaciónCada 50 horas mantenimiento Mantenimiento del silenciador Almacenamiento de largo plazoCada 135 horas de operación, retire y limpie el silenciador Para limar en ángulos iguales, use una Rendimiento de la cadenaGuía para la lima Guía de localización de fallas Qué revisarPosible causa RemedioGuía de localización de fallas continuación Qué revisar Posible causa RemedioDeclaración de Garantía del Sistema de Emisión Notas Tronçonneuse à perche P231 Introduction Mises en garde UnénoncéprécédédelamentionLes échappements du moteur De ce produit contiennent des subConsignes de sécurité Réaliser les coupes à haut régimeConsignes d’utilisation Équipement complet de l’utilisateurNe pas utiliser l’appareil sans le silencieux Consignes d’utilisation suite Étiquettes et dispositifs de sécuritéNomenclature Caractéristiques techniquesAvant l’assemblage Montage de la tête motoriséeOptions du guide-chaîne et de la chaîne Raccord du câble d’accélérationAssemblage suite Raccorder le câble d’accélérationRéglage du câble d’accélération Assemblage les éléments du tubeInstallation de la chaîne Installation et réglage du guide-chaîne et de la chaîneDésassemblage des éléments Réglage de la chaîne Huileur de chaîneRemplissage du réservoir d’huile Réglage du débit d’huileMélange de carburant Remplissage du réservoir de carburantDémarrage du moteur Lorsque le moteur démarreRéglage du ralenti du moteur Arrêt du moteurVérification et réglage du ré- gime de ralenti Utilisation de la tronçonneuse Entretien Entretien quotidienEntretien aux 10 heures SilencieuxEntretien suite Remisage à long termeEntretien aux 10 à 15 heures Entretien aux 50 heuresEntretien du pare-étincelles Enlever le capuchon de la bougieAffûtage de la chaîne Technique d’affûtage correcteSolution Points à contrôler Cause probable SolutionGuide de dépannage Points à contrôlerGuide de dépannage suite Cause probableDéclaration de garantie du dispositif antipollution FR22 FR23 FR24

62891-94311 specifications

The Shindaiwa 62891-94311 is a premium combination of engineering and technology, designed for lawn care and landscaping professionals. This tool provides efficient and reliable performance, making it a top choice for outdoor enthusiasts and contractors alike. One of the standout features of the Shindaiwa 62891-94311 is its lightweight yet durable construction. This ensures that it delivers high performance without sacrificing user comfort, allowing operators to work for extended periods without undue fatigue.

This model is equipped with advanced engine technology that enhances fuel efficiency and reduces emissions. The 2-stroke engine not only delivers impressive power but also adheres to stringent environmental regulations. Users appreciate the reduced environmental footprint, which aligns with a growing trend towards sustainability in landscaping equipment.

Another key characteristic of the Shindaiwa 62891-94311 is its ergonomic design. The handle is designed for optimum comfort and control, reducing vibration during use, which leads to greater precision and reduces the risk of strain injuries. The combination of the lightweight structure and ergonomic grip allows for longer operational hours, ensuring that users can tackle large projects efficiently.

The product features easy-start technology, enabling quick and effortless ignition. This is particularly beneficial for professionals who need to maximize productivity on job sites. Additionally, the model includes an adjustable throttle, allowing users to easily adapt the power output according to their specific needs, whether it’s for trimming, edging, or heavy-duty cutting tasks.

Durability is another focus for the Shindaiwa 62891-94311. The materials used in its construction are engineered to withstand the rigors of outdoor use, ensuring longevity and reliability. This means that users can invest in this tool with confidence, knowing it can handle extensive workloads and still perform optimally.

In conclusion, the Shindaiwa 62891-94311 is a versatile and powerful tool that incorporates advanced technology, ergonomic design, and durability. It is an ideal choice for landscaping professionals seeking a reliable, efficient, and eco-friendly solution for their outdoor tasks. Whether trimming hedges or tackling tough underbrush, this model stands out as a preferred option in the field of outdoor power equipment.
Top Page Image Contents