Shindaiwa 62891-94311 Assembly, Prior to assembly, Powerhead Installation, Bar and Chain Options

Page 7

Assembly

Prior to assembly

 

 

Using Figure above as a guide, familiar-

■ Powerhead Assembly

ize yourself with the Shindaiwa P231

■ Lower Tube Assembly

pole pruner and its various components.

■ Upper Tube/Saw Assembly, Chain and

Understanding your unit helps ensure

top performance, longer service life, and

Guide Bar

■ Chain CoverTool Kit Containing:

safer operation.

 

•

Spark Plug Wrench

Before assembling, make sure you have

•

4mm Hex Wrench

all the components required for a com-

•

8 x 10mm Spanner

plete unit:

Carefully inspect all components for damage.

 

IMPORTANT!

The terms “left”, “left-hand”, and “LH”; “right”, “right-hand”, and “RH”; “front” and “rear” refer to directions as viewed by the operator during normal operation.

WARNING!

Do not make unauthorized modifications or alterations to your pruner or its components.

Powerhead Installation

1.Place the powerhead on a clean, flat surface, spark plug facing up.

2.Use the 4mm hex wrench to loosen the tube clamp screw. Verify that the D-shaped shim washer is positioned as shown below.

Tube Clamp

Hex

Wrench

3.Add some moly-type EP grease to splines at the end of the main shaft.

CAUTION!

Do not force the shaft tube into the powerhead! Excessive force can damage the shaft tube and mainshaft.

4.Slide the outer tube into the tube clamp until the tube bottoms. If installation is difficult, rotate the outer tube or main shaft slightly until you feel the mainshaft splines engage with the powerhead. Outer tube needs to be inserted so that the end of the grip hits joint cap.

5.Position the outer tube so that the igni- tion switch is facing up and the throttle lever is facing down.

Bar and Chain Options

8 inch Bar — 90SG-33E Chain

10 inch Bar — 90SG-39E Chain

12 inch Bar — 90SG-44E Chain

6.Slide the outer tube into the powerhead until the throttle grip just contacts the tube clamp.

7.Tighten the clamp screw firmly.

 

 

Main

Tube

 

 

Clamp

 

Outer

Shaft

 

 

Tube

 

 

Ignition

Grip

 

 

Switch

 

 

 

 

 

 

Clamp Screw

 

Throttle Lever

Connecting the Throttle Cable

Remove The Cylinder Cover

1.Remove the spark plug boot.

2.Remove the two lower cylinder cover screws.

3.Loosen the top cylinder cover screw until the cover is free of the engine. (The top cylinder cover screw is captive). Lift the cylinder cover off of the engine.

Top Cylinder

Cover Screw

Hex Wrench

Spark Plug

Boot

Lower Cylinder

Cover Screws

Page 6 Page 8
Image 7
Page 6 Page 8
Contents P231 Pole Pruner Introduction ContentsBeware of pinching Safety PrecautionsKickback and Pinching Beware of KickbackOperating Precautions Operating PrecautionsProperly Equipped Operator Safety Equipment and Labels Product Description Technical SpecificationsConnecting the Throttle Cable AssemblyPrior to assembly Powerhead InstallationAssembling tube sections Adjusting the Throttle CableKeep the open ends of the tubes clean and free of debris Connect The Throttle CableInstalling the Chain Installing and Adjusting the Bar and ChainDisassembling the tube sections Chain Oiler Adjusting the ChainAdjusting Oil Flow Rate Adjust the pump as followsAlways transport and store fuels in an approved container Mixing FuelFilling the Fuel Tank Minimize the risk of fire, burns, and personal injuryStarting the Engine When the Engine StartsNever start the engine from the operating position Check and Adjust Idle Speed Adjusting the Engine IdleStopping the Engine Using the Pole Pruner Muffler General MaintenanceDaily Maintenance Hour MaintenanceClean or replace fuel filter 10/15-Hour MaintenanceEvery 10 to 15 hours of operation Long Term Storage MaintenanceMuffler maintenance Every 135 hours of operation, remove and clean the mufflerFor consistent filing angles, use a filing guide Sharpening the ChainWhat To Check Troubleshooting GuideSymptom Possible Cause Emission System Warranty Statement Fax Specifications subject to change without notice P231 Podadora de Extensión Índice Introducción Declaraciones de seguridadGuardarte de contragolpe Instrucciones generales de seguridadTrabaje con cuidado ¡ADVERTENCIA! Contragolpe y aprieteInstrucciones de seguridad El operario debidamente equipadoPrecauciones del funcionamiento Etiquetas de seguridad Instrucciones de seguridad continuaciónRealice siempre el mantenimiento Especificaciones Descripción del productoConexión del cable del acelerador EnsamblarAntes de Ensamblar Barras y cadenas opcionalesEnsamblar de las secciones del tubo Ensamblar continuaciónConecte el cable del acelerador Ajuste el cable del aceleradorDesmontaje de las secciones del tubo Instalación y ajuste de la barra y la cadena de la sierraInstalación la cadena Ajuste del flujo del aceite Adjuste la cadenaBomba de aceite Llenado del depósito de aceite¡ADVERTENCIA! Disminuya el riesgo de incendios Mezcla de combustibleLlenando el tanque de combustible Ejemplos de cantidades de mezcla a proporción deNunca arranque el motor desde la posición de operación Arranque del motorCuando arranca el motor… Continuar girando cuando se para El motor Parada del motorAjuste de marcha mínima del motor El accesorio de cortes pudoEl uso de la potadora de extensión Mantenimiento diario Mantenimiento generalCada 10 horas mantenimiento Cada 10 15 horas mantenimiento Mantenimiento continuaciónCada 50 horas mantenimiento Mantenimiento del silenciador Almacenamiento de largo plazoCada 135 horas de operación, retire y limpie el silenciador Para limar en ángulos iguales, use una Rendimiento de la cadenaGuía para la lima Remedio Guía de localización de fallasQué revisar Posible causaQué revisar Posible causa Remedio Guía de localización de fallas continuaciónDeclaración de Garantía del Sistema de Emisión Notas Tronçonneuse à perche P231 De ce produit contiennent des sub Introduction Mises en gardeUnénoncéprécédédelamention Les échappements du moteurRéaliser les coupes à haut régime Consignes de sécuritéConsignes d’utilisation Équipement complet de l’utilisateurNe pas utiliser l’appareil sans le silencieux Étiquettes et dispositifs de sécurité Consignes d’utilisation suiteCaractéristiques techniques NomenclatureRaccord du câble d’accélération Avant l’assemblageMontage de la tête motorisée Options du guide-chaîne et de la chaîneAssemblage les éléments du tube Assemblage suiteRaccorder le câble d’accélération Réglage du câble d’accélérationInstallation de la chaîne Installation et réglage du guide-chaîne et de la chaîneDésassemblage des éléments Réglage du débit d’huile Réglage de la chaîneHuileur de chaîne Remplissage du réservoir d’huileRemplissage du réservoir de carburant Mélange de carburantLorsque le moteur démarre Démarrage du moteurRéglage du ralenti du moteur Arrêt du moteurVérification et réglage du ré- gime de ralenti Utilisation de la tronçonneuse Silencieux EntretienEntretien quotidien Entretien aux 10 heuresEntretien aux 50 heures Entretien suiteRemisage à long terme Entretien aux 10 à 15 heuresEnlever le capuchon de la bougie Entretien du pare-étincellesTechnique d’affûtage correcte Affûtage de la chaînePoints à contrôler SolutionPoints à contrôler Cause probable Solution Guide de dépannageCause probable Guide de dépannage suiteDéclaration de garantie du dispositif antipollution FR22 FR23 FR24

62891-94311 specifications

The Shindaiwa 62891-94311 is a premium combination of engineering and technology, designed for lawn care and landscaping professionals. This tool provides efficient and reliable performance, making it a top choice for outdoor enthusiasts and contractors alike. One of the standout features of the Shindaiwa 62891-94311 is its lightweight yet durable construction. This ensures that it delivers high performance without sacrificing user comfort, allowing operators to work for extended periods without undue fatigue.

This model is equipped with advanced engine technology that enhances fuel efficiency and reduces emissions. The 2-stroke engine not only delivers impressive power but also adheres to stringent environmental regulations. Users appreciate the reduced environmental footprint, which aligns with a growing trend towards sustainability in landscaping equipment.

Another key characteristic of the Shindaiwa 62891-94311 is its ergonomic design. The handle is designed for optimum comfort and control, reducing vibration during use, which leads to greater precision and reduces the risk of strain injuries. The combination of the lightweight structure and ergonomic grip allows for longer operational hours, ensuring that users can tackle large projects efficiently.

The product features easy-start technology, enabling quick and effortless ignition. This is particularly beneficial for professionals who need to maximize productivity on job sites. Additionally, the model includes an adjustable throttle, allowing users to easily adapt the power output according to their specific needs, whether it’s for trimming, edging, or heavy-duty cutting tasks.

Durability is another focus for the Shindaiwa 62891-94311. The materials used in its construction are engineered to withstand the rigors of outdoor use, ensuring longevity and reliability. This means that users can invest in this tool with confidence, knowing it can handle extensive workloads and still perform optimally.

In conclusion, the Shindaiwa 62891-94311 is a versatile and powerful tool that incorporates advanced technology, ergonomic design, and durability. It is an ideal choice for landscaping professionals seeking a reliable, efficient, and eco-friendly solution for their outdoor tasks. Whether trimming hedges or tackling tough underbrush, this model stands out as a preferred option in the field of outdoor power equipment.
Top Page Image Contents