Shindaiwa 62891-94311 Starting the Engine, Never start the engine from the operating position

Page 12

Starting the Engine

IMPORTANT!

Engine ignition is controlled by a two position switch mounted on the throttle housing labeled, “I” for ON or START and “O” for OFF or STOP.

Ignition

Switch

Throttle

Lever

1.Slide the ignition switch to the “ON” position.

Primer Bulb

Return

 

Tube

 

 

2.Press the primer bulb until fuel can be seen flowing in the transparent return tube.

IMPORTANT!

The primer system only pushes fuel through the carburetor. Repeatedly press- ing the primer bulb will not flood the engine with fuel.

3.Set the choke lever to the CLOSED position if engine is cold.

Closed

4.While holding the outer tube firmly with one hand, slowly pull the recoil starter handle until resistance is felt, then pull quickly to start the engine.

Make sure the

cutting attachment is clear of obstructions!

CAUTION!

Do not pull the recoil starter to the end of the rope travel. Pulling the recoil starter to the end of the rope travel can damage the starter.

Open

5.When the engine starts, slowly move the choke lever to the “OPEN” posi- tion. (If the engine stops after the initial start, close the choke and restart.)

WARNING!

The cutting blades may move when the engine is started. Keep away from the cutter assembly while starting the engine.

IMPORTANT!

If the engine fails to start after several attempts with the choke in the closed position, the engine may be flooded with fuel. If flooding is suspected, move the choke lever to the open position and repeatedly pull the recoil starter to remove excess fuel and start the engine. If the engine still fails to start, refer to the troubleshooting section of this manual.

WARNING!

Never start the engine from the operating position.

When the Engine Starts...

■After the engine starts, allow the engine to warm up at idle 2 or 3 minutes before operating the unit.

■After the engine is warm, pick up the unit and clip on the shoulder strap if so equipped.

■Advancing the throttle makes the cutting attachment turn faster; releasing the throttle permits the attachment to stop turning. If the cutting attachment continues to rotate when the engine returns to idle, carburetor idle speed should be adjusted (see “Adjusting The Engine Idle” on the next page).

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents P231 Pole Pruner Contents IntroductionSafety Precautions Kickback and PinchingBeware of Kickback Beware of pinchingOperating Precautions Operating PrecautionsProperly Equipped Operator Safety Equipment and Labels Technical Specifications Product DescriptionAssembly Prior to assemblyPowerhead Installation Connecting the Throttle CableAdjusting the Throttle Cable Keep the open ends of the tubes clean and free of debrisConnect The Throttle Cable Assembling tube sectionsInstalling and Adjusting the Bar and Chain Installing the ChainDisassembling the tube sections Adjusting the Chain Adjusting Oil Flow RateAdjust the pump as follows Chain OilerMixing Fuel Filling the Fuel TankMinimize the risk of fire, burns, and personal injury Always transport and store fuels in an approved containerWhen the Engine Starts Starting the EngineNever start the engine from the operating position Adjusting the Engine Idle Check and Adjust Idle SpeedStopping the Engine Using the Pole Pruner General Maintenance Daily MaintenanceHour Maintenance Muffler10/15-Hour Maintenance Clean or replace fuel filterEvery 10 to 15 hours of operation Maintenance Muffler maintenanceEvery 135 hours of operation, remove and clean the muffler Long Term StorageSharpening the Chain For consistent filing angles, use a filing guideTroubleshooting Guide What To CheckSymptom Possible Cause Emission System Warranty Statement Fax Specifications subject to change without notice P231 Podadora de Extensión Introducción Declaraciones de seguridad ÍndiceInstrucciones generales de seguridad Trabaje con cuidado¡ADVERTENCIA! Contragolpe y apriete Guardarte de contragolpeEl operario debidamente equipado Instrucciones de seguridadPrecauciones del funcionamiento Instrucciones de seguridad continuación Etiquetas de seguridadRealice siempre el mantenimiento Descripción del producto EspecificacionesEnsamblar Antes de EnsamblarBarras y cadenas opcionales Conexión del cable del aceleradorEnsamblar continuación Conecte el cable del aceleradorAjuste el cable del acelerador Ensamblar de las secciones del tuboInstalación y ajuste de la barra y la cadena de la sierra Desmontaje de las secciones del tuboInstalación la cadena Adjuste la cadena Bomba de aceiteLlenado del depósito de aceite Ajuste del flujo del aceiteMezcla de combustible Llenando el tanque de combustibleEjemplos de cantidades de mezcla a proporción de ¡ADVERTENCIA! Disminuya el riesgo de incendiosArranque del motor Nunca arranque el motor desde la posición de operaciónCuando arranca el motor… Parada del motor Ajuste de marcha mínima del motorEl accesorio de cortes pudo Continuar girando cuando se para El motorEl uso de la potadora de extensión Mantenimiento general Mantenimiento diarioCada 10 horas mantenimiento Mantenimiento continuación Cada 10 15 horas mantenimientoCada 50 horas mantenimiento Almacenamiento de largo plazo Mantenimiento del silenciadorCada 135 horas de operación, retire y limpie el silenciador Rendimiento de la cadena Para limar en ángulos iguales, use unaGuía para la lima Guía de localización de fallas Qué revisarPosible causa RemedioGuía de localización de fallas continuación Qué revisar Posible causa RemedioDeclaración de Garantía del Sistema de Emisión Notas Tronçonneuse à perche P231 Introduction Mises en garde UnénoncéprécédédelamentionLes échappements du moteur De ce produit contiennent des subConsignes de sécurité Réaliser les coupes à haut régimeÉquipement complet de l’utilisateur Consignes d’utilisationNe pas utiliser l’appareil sans le silencieux Consignes d’utilisation suite Étiquettes et dispositifs de sécuritéNomenclature Caractéristiques techniquesAvant l’assemblage Montage de la tête motoriséeOptions du guide-chaîne et de la chaîne Raccord du câble d’accélérationAssemblage suite Raccorder le câble d’accélérationRéglage du câble d’accélération Assemblage les éléments du tubeInstallation et réglage du guide-chaîne et de la chaîne Installation de la chaîneDésassemblage des éléments Réglage de la chaîne Huileur de chaîneRemplissage du réservoir d’huile Réglage du débit d’huileMélange de carburant Remplissage du réservoir de carburantDémarrage du moteur Lorsque le moteur démarreArrêt du moteur Réglage du ralenti du moteurVérification et réglage du ré- gime de ralenti Utilisation de la tronçonneuse Entretien Entretien quotidienEntretien aux 10 heures SilencieuxEntretien suite Remisage à long termeEntretien aux 10 à 15 heures Entretien aux 50 heuresEntretien du pare-étincelles Enlever le capuchon de la bougieAffûtage de la chaîne Technique d’affûtage correcteSolution Points à contrôler Cause probable SolutionGuide de dépannage Points à contrôlerGuide de dépannage suite Cause probableDéclaration de garantie du dispositif antipollution FR22 FR23 FR24

62891-94311 specifications

The Shindaiwa 62891-94311 is a premium combination of engineering and technology, designed for lawn care and landscaping professionals. This tool provides efficient and reliable performance, making it a top choice for outdoor enthusiasts and contractors alike. One of the standout features of the Shindaiwa 62891-94311 is its lightweight yet durable construction. This ensures that it delivers high performance without sacrificing user comfort, allowing operators to work for extended periods without undue fatigue.

This model is equipped with advanced engine technology that enhances fuel efficiency and reduces emissions. The 2-stroke engine not only delivers impressive power but also adheres to stringent environmental regulations. Users appreciate the reduced environmental footprint, which aligns with a growing trend towards sustainability in landscaping equipment.

Another key characteristic of the Shindaiwa 62891-94311 is its ergonomic design. The handle is designed for optimum comfort and control, reducing vibration during use, which leads to greater precision and reduces the risk of strain injuries. The combination of the lightweight structure and ergonomic grip allows for longer operational hours, ensuring that users can tackle large projects efficiently.

The product features easy-start technology, enabling quick and effortless ignition. This is particularly beneficial for professionals who need to maximize productivity on job sites. Additionally, the model includes an adjustable throttle, allowing users to easily adapt the power output according to their specific needs, whether it’s for trimming, edging, or heavy-duty cutting tasks.

Durability is another focus for the Shindaiwa 62891-94311. The materials used in its construction are engineered to withstand the rigors of outdoor use, ensuring longevity and reliability. This means that users can invest in this tool with confidence, knowing it can handle extensive workloads and still perform optimally.

In conclusion, the Shindaiwa 62891-94311 is a versatile and powerful tool that incorporates advanced technology, ergonomic design, and durability. It is an ideal choice for landscaping professionals seeking a reliable, efficient, and eco-friendly solution for their outdoor tasks. Whether trimming hedges or tackling tough underbrush, this model stands out as a preferred option in the field of outdoor power equipment.
Top Page Image Contents