Shindaiwa 62891-94311 manual Symptom Possible Cause

Page 20

Troubleshooting Guide (continued)

Additional Problems

Symptom

Possible Cause

Remedy

Poor acceleration.

Clogged air filter. Clogged fuel filter. Chain brake engaged.

Lean fuel/air mixture. Idle speed set too low.

Clean or replace the air filter.

Replace the fuel filter.

Inspect and/or test brake. Consult with an authorized servicing dealer.

Consult with an authorized servicing dealer.

Adjust: 2,750(±250) min-1.

Engine stops abruptly.

Switch turned off.

Fuel tank empty.

Clogged fuel filter.

Water in the fuel.

Shorted spark plug or loose terminal.

Ignition failure.

Piston seizure.

Reset the switch and restart.

Refuel. See section on “Filling the Tank with Fuel”.

Replace fuel filter.

Drain; replace with clean fuel. See section on “Filling the Tank with Fuel”.

Clean or replace spark plug. See “Specifications” for the correct plug for your unit. Tighten the terminal.

Replace the ignition unit.

Consult with an authorized servicing dealer.

Engine difficult to shut off.

Ground (stop) wire is disconnected, or switch is defective.

Overheating due to incorrect spark plug.

Overheated engine

Test and replace as required.

Replace spark plug. See “Specifications” for the correct plug for your unit.

Idle engine until cool.

Chain rotates at idle speed.

Engine idle too high.

Replace spring/shoes as required, check idle speed. Set idle: 2,750(±250) min-1

Excessive vibration.

Broken clutch spring or worn clutch spring boss Warped or damaged sprocket, chain, or bar.

Bent crankshaft.

Inspect and replace chain components as required.

Consult with an authorized servicing dealer.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents P231 Pole Pruner Contents IntroductionSafety Precautions Kickback and PinchingBeware of Kickback Beware of pinchingProperly Equipped Operator Operating PrecautionsOperating Precautions Safety Equipment and Labels Technical Specifications Product DescriptionAssembly Prior to assemblyPowerhead Installation Connecting the Throttle CableAdjusting the Throttle Cable Keep the open ends of the tubes clean and free of debrisConnect The Throttle Cable Assembling tube sectionsDisassembling the tube sections Installing and Adjusting the Bar and ChainInstalling the Chain Adjusting the Chain Adjusting Oil Flow RateAdjust the pump as follows Chain OilerMixing Fuel Filling the Fuel TankMinimize the risk of fire, burns, and personal injury Always transport and store fuels in an approved containerNever start the engine from the operating position When the Engine StartsStarting the Engine Stopping the Engine Adjusting the Engine IdleCheck and Adjust Idle Speed Using the Pole Pruner General Maintenance Daily MaintenanceHour Maintenance MufflerEvery 10 to 15 hours of operation 10/15-Hour MaintenanceClean or replace fuel filter Maintenance Muffler maintenanceEvery 135 hours of operation, remove and clean the muffler Long Term StorageSharpening the Chain For consistent filing angles, use a filing guideTroubleshooting Guide What To CheckSymptom Possible Cause Emission System Warranty Statement Fax Specifications subject to change without notice P231 Podadora de Extensión Introducción Declaraciones de seguridad ÍndiceInstrucciones generales de seguridad Trabaje con cuidado¡ADVERTENCIA! Contragolpe y apriete Guardarte de contragolpePrecauciones del funcionamiento El operario debidamente equipadoInstrucciones de seguridad Realice siempre el mantenimiento Instrucciones de seguridad continuaciónEtiquetas de seguridad Descripción del producto EspecificacionesEnsamblar Antes de EnsamblarBarras y cadenas opcionales Conexión del cable del aceleradorEnsamblar continuación Conecte el cable del aceleradorAjuste el cable del acelerador Ensamblar de las secciones del tuboInstalación la cadena Instalación y ajuste de la barra y la cadena de la sierraDesmontaje de las secciones del tubo Adjuste la cadena Bomba de aceiteLlenado del depósito de aceite Ajuste del flujo del aceiteMezcla de combustible Llenando el tanque de combustibleEjemplos de cantidades de mezcla a proporción de ¡ADVERTENCIA! Disminuya el riesgo de incendiosCuando arranca el motor… Arranque del motorNunca arranque el motor desde la posición de operación Parada del motor Ajuste de marcha mínima del motorEl accesorio de cortes pudo Continuar girando cuando se para El motorEl uso de la potadora de extensión Cada 10 horas mantenimiento Mantenimiento generalMantenimiento diario Cada 50 horas mantenimiento Mantenimiento continuaciónCada 10 15 horas mantenimiento Cada 135 horas de operación, retire y limpie el silenciador Almacenamiento de largo plazoMantenimiento del silenciador Guía para la lima Rendimiento de la cadenaPara limar en ángulos iguales, use una Guía de localización de fallas Qué revisarPosible causa RemedioGuía de localización de fallas continuación Qué revisar Posible causa RemedioDeclaración de Garantía del Sistema de Emisión Notas Tronçonneuse à perche P231 Introduction Mises en garde UnénoncéprécédédelamentionLes échappements du moteur De ce produit contiennent des subConsignes de sécurité Réaliser les coupes à haut régimeNe pas utiliser l’appareil sans le silencieux Équipement complet de l’utilisateurConsignes d’utilisation Consignes d’utilisation suite Étiquettes et dispositifs de sécuritéNomenclature Caractéristiques techniquesAvant l’assemblage Montage de la tête motoriséeOptions du guide-chaîne et de la chaîne Raccord du câble d’accélérationAssemblage suite Raccorder le câble d’accélérationRéglage du câble d’accélération Assemblage les éléments du tubeDésassemblage des éléments Installation et réglage du guide-chaîne et de la chaîneInstallation de la chaîne Réglage de la chaîne Huileur de chaîneRemplissage du réservoir d’huile Réglage du débit d’huileMélange de carburant Remplissage du réservoir de carburantDémarrage du moteur Lorsque le moteur démarreVérification et réglage du ré- gime de ralenti Arrêt du moteurRéglage du ralenti du moteur Utilisation de la tronçonneuse Entretien Entretien quotidienEntretien aux 10 heures SilencieuxEntretien suite Remisage à long termeEntretien aux 10 à 15 heures Entretien aux 50 heuresEntretien du pare-étincelles Enlever le capuchon de la bougieAffûtage de la chaîne Technique d’affûtage correcteSolution Points à contrôler Cause probable SolutionGuide de dépannage Points à contrôlerGuide de dépannage suite Cause probableDéclaration de garantie du dispositif antipollution FR22 FR23 FR24

62891-94311 specifications

The Shindaiwa 62891-94311 is a premium combination of engineering and technology, designed for lawn care and landscaping professionals. This tool provides efficient and reliable performance, making it a top choice for outdoor enthusiasts and contractors alike. One of the standout features of the Shindaiwa 62891-94311 is its lightweight yet durable construction. This ensures that it delivers high performance without sacrificing user comfort, allowing operators to work for extended periods without undue fatigue.

This model is equipped with advanced engine technology that enhances fuel efficiency and reduces emissions. The 2-stroke engine not only delivers impressive power but also adheres to stringent environmental regulations. Users appreciate the reduced environmental footprint, which aligns with a growing trend towards sustainability in landscaping equipment.

Another key characteristic of the Shindaiwa 62891-94311 is its ergonomic design. The handle is designed for optimum comfort and control, reducing vibration during use, which leads to greater precision and reduces the risk of strain injuries. The combination of the lightweight structure and ergonomic grip allows for longer operational hours, ensuring that users can tackle large projects efficiently.

The product features easy-start technology, enabling quick and effortless ignition. This is particularly beneficial for professionals who need to maximize productivity on job sites. Additionally, the model includes an adjustable throttle, allowing users to easily adapt the power output according to their specific needs, whether it’s for trimming, edging, or heavy-duty cutting tasks.

Durability is another focus for the Shindaiwa 62891-94311. The materials used in its construction are engineered to withstand the rigors of outdoor use, ensuring longevity and reliability. This means that users can invest in this tool with confidence, knowing it can handle extensive workloads and still perform optimally.

In conclusion, the Shindaiwa 62891-94311 is a versatile and powerful tool that incorporates advanced technology, ergonomic design, and durability. It is an ideal choice for landscaping professionals seeking a reliable, efficient, and eco-friendly solution for their outdoor tasks. Whether trimming hedges or tackling tough underbrush, this model stands out as a preferred option in the field of outdoor power equipment.
Top Page Image Contents