Shindaiwa 62891-94311 manual Technical Specifications, Product Description

Page 6

Product Description

Guide Bar and

Chain

Upper Tube

Coupler

Air Filter Assembly

Top Engine Cover

 

Screw

 

Spark Plug

Recoil Starter

Fuel Tank

Powerhead Assembly

Handle

Grip

Gearcase

Oil Filler Cap

Guide Bar and

 

 

Chain

 

Cutting Head

Bar Oil Reservoir

Assembly

Ignition Switch

Lower Tube

Throttle Trigger

Technical Specifications

Dry Weight

6.1 kg/13.4 lb.

Length w/10" bar assembly

2804 mm/110.4 in.

Engine Type

2-cycle, air-cooled, vertical-cylinder

Bore x Stroke

32 x 28 mm/1.3 x 1.1 in.

Displacement

22.5 cc/1.4 cu. in.

Maximum Output

0.8kW/1.1 hp @ 7500 min-1 (rpm)

Fuel/oil ratio

50:1

Fuel Tank Capacity

670 ml/22.7 oz.

Carburetor Type

Walbro WYL-122

Ignition

One-piece, electronic, transistor-controlled

Spark Plug

NGK BMR6A

Air Filter

Non-reversible flocked filter element

Muffler Type

2-Stage Catalyst

Starting Method

Recoil

Cooling System

Forced air

Stopping Method

Slide switch

Transmission Type

Automatic, centrifugal clutch with bevel gear

Chain Guide Bar

3/8" pitch, .043" gauge, 10-inch Micro Lite™

Chain Type

3/8" pitch Micro Lite™, .043" gauge

Sprockets

3/8-inch, fixed spur

Gearcase Ratio

1.06 : 1

Chain Speed

23.5 m (77 ft.)/sec.@ 10,000 min-1 (rpm)

Chain Lubrication

Automatic adjustable oiler

Chain Lubricant

Shindaiwa Premium Bar and Chain Oil

Optional Equipment

Shoulder strap, loop handle

Optional Bars

8-inch or 12-inch

EPA Emission Compliance Period*

Category A

* The EPA emission compliance referred to on the emission compliance label located on the engine, indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements. Category C = 50 hours (Moderate), B = 125 hours (Intermediate) and A = 300 hours (Extended).

Page 5 Page 7
Image 6
Page 5 Page 7
Contents P231 Pole Pruner Contents IntroductionBeware of Kickback Safety PrecautionsKickback and Pinching Beware of pinchingOperating Precautions Operating PrecautionsProperly Equipped Operator Safety Equipment and Labels Technical Specifications Product DescriptionPowerhead Installation AssemblyPrior to assembly Connecting the Throttle CableConnect The Throttle Cable Adjusting the Throttle CableKeep the open ends of the tubes clean and free of debris Assembling tube sectionsInstalling and Adjusting the Bar and Chain Installing the ChainDisassembling the tube sections Adjust the pump as follows Adjusting the ChainAdjusting Oil Flow Rate Chain OilerMinimize the risk of fire, burns, and personal injury Mixing FuelFilling the Fuel Tank Always transport and store fuels in an approved containerWhen the Engine Starts Starting the EngineNever start the engine from the operating position Adjusting the Engine Idle Check and Adjust Idle SpeedStopping the Engine Using the Pole Pruner Hour Maintenance General MaintenanceDaily Maintenance Muffler10/15-Hour Maintenance Clean or replace fuel filterEvery 10 to 15 hours of operation Every 135 hours of operation, remove and clean the muffler MaintenanceMuffler maintenance Long Term StorageSharpening the Chain For consistent filing angles, use a filing guideTroubleshooting Guide What To CheckSymptom Possible Cause Emission System Warranty Statement Fax Specifications subject to change without notice P231 Podadora de Extensión Introducción Declaraciones de seguridad Índice¡ADVERTENCIA! Contragolpe y apriete Instrucciones generales de seguridadTrabaje con cuidado Guardarte de contragolpeEl operario debidamente equipado Instrucciones de seguridadPrecauciones del funcionamiento Instrucciones de seguridad continuación Etiquetas de seguridadRealice siempre el mantenimiento Descripción del producto EspecificacionesBarras y cadenas opcionales EnsamblarAntes de Ensamblar Conexión del cable del aceleradorAjuste el cable del acelerador Ensamblar continuaciónConecte el cable del acelerador Ensamblar de las secciones del tuboInstalación y ajuste de la barra y la cadena de la sierra Desmontaje de las secciones del tuboInstalación la cadena Llenado del depósito de aceite Adjuste la cadenaBomba de aceite Ajuste del flujo del aceiteEjemplos de cantidades de mezcla a proporción de Mezcla de combustibleLlenando el tanque de combustible ¡ADVERTENCIA! Disminuya el riesgo de incendiosArranque del motor Nunca arranque el motor desde la posición de operaciónCuando arranca el motor… El accesorio de cortes pudo Parada del motorAjuste de marcha mínima del motor Continuar girando cuando se para El motorEl uso de la potadora de extensión Mantenimiento general Mantenimiento diarioCada 10 horas mantenimiento Mantenimiento continuación Cada 10 15 horas mantenimientoCada 50 horas mantenimiento Almacenamiento de largo plazo Mantenimiento del silenciadorCada 135 horas de operación, retire y limpie el silenciador Rendimiento de la cadena Para limar en ángulos iguales, use unaGuía para la lima Posible causa Guía de localización de fallasQué revisar RemedioGuía de localización de fallas continuación Qué revisar Posible causa RemedioDeclaración de Garantía del Sistema de Emisión Notas Tronçonneuse à perche P231 Les échappements du moteur Introduction Mises en gardeUnénoncéprécédédelamention De ce produit contiennent des subConsignes de sécurité Réaliser les coupes à haut régimeÉquipement complet de l’utilisateur Consignes d’utilisationNe pas utiliser l’appareil sans le silencieux Consignes d’utilisation suite Étiquettes et dispositifs de sécuritéNomenclature Caractéristiques techniquesOptions du guide-chaîne et de la chaîne Avant l’assemblageMontage de la tête motorisée Raccord du câble d’accélérationRéglage du câble d’accélération Assemblage suiteRaccorder le câble d’accélération Assemblage les éléments du tubeInstallation et réglage du guide-chaîne et de la chaîne Installation de la chaîneDésassemblage des éléments Remplissage du réservoir d’huile Réglage de la chaîneHuileur de chaîne Réglage du débit d’huileMélange de carburant Remplissage du réservoir de carburantDémarrage du moteur Lorsque le moteur démarreArrêt du moteur Réglage du ralenti du moteurVérification et réglage du ré- gime de ralenti Utilisation de la tronçonneuse Entretien aux 10 heures EntretienEntretien quotidien SilencieuxEntretien aux 10 à 15 heures Entretien suiteRemisage à long terme Entretien aux 50 heuresEntretien du pare-étincelles Enlever le capuchon de la bougieAffûtage de la chaîne Technique d’affûtage correcteGuide de dépannage SolutionPoints à contrôler Cause probable Solution Points à contrôlerGuide de dépannage suite Cause probableDéclaration de garantie du dispositif antipollution FR22 FR23 FR24

62891-94311 specifications

The Shindaiwa 62891-94311 is a premium combination of engineering and technology, designed for lawn care and landscaping professionals. This tool provides efficient and reliable performance, making it a top choice for outdoor enthusiasts and contractors alike. One of the standout features of the Shindaiwa 62891-94311 is its lightweight yet durable construction. This ensures that it delivers high performance without sacrificing user comfort, allowing operators to work for extended periods without undue fatigue.

This model is equipped with advanced engine technology that enhances fuel efficiency and reduces emissions. The 2-stroke engine not only delivers impressive power but also adheres to stringent environmental regulations. Users appreciate the reduced environmental footprint, which aligns with a growing trend towards sustainability in landscaping equipment.

Another key characteristic of the Shindaiwa 62891-94311 is its ergonomic design. The handle is designed for optimum comfort and control, reducing vibration during use, which leads to greater precision and reduces the risk of strain injuries. The combination of the lightweight structure and ergonomic grip allows for longer operational hours, ensuring that users can tackle large projects efficiently.

The product features easy-start technology, enabling quick and effortless ignition. This is particularly beneficial for professionals who need to maximize productivity on job sites. Additionally, the model includes an adjustable throttle, allowing users to easily adapt the power output according to their specific needs, whether it’s for trimming, edging, or heavy-duty cutting tasks.

Durability is another focus for the Shindaiwa 62891-94311. The materials used in its construction are engineered to withstand the rigors of outdoor use, ensuring longevity and reliability. This means that users can invest in this tool with confidence, knowing it can handle extensive workloads and still perform optimally.

In conclusion, the Shindaiwa 62891-94311 is a versatile and powerful tool that incorporates advanced technology, ergonomic design, and durability. It is an ideal choice for landscaping professionals seeking a reliable, efficient, and eco-friendly solution for their outdoor tasks. Whether trimming hedges or tackling tough underbrush, this model stands out as a preferred option in the field of outdoor power equipment.
Top Page Image Contents