Shindaiwa 62891-94311 manual General Maintenance, Daily Maintenance, Hour Maintenance, Muffler

Page 15

General Maintenance

IMPORTANT!

MAINTENANCE, REPLACEMENT, OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEM MAY BE PERFORMED BY ANY REPAIR ESTAB- LISHMENT OR INDIVIDUAL. HOW- EVER, WARRANTY REPAIRS MUST BE PERFORMED BY A DEALER OR SERVICE CENTER AUTHORIZED BY SHINDAIWA KOGYO, LTD. AND USE OF PARTS THAT ARE NOT EQUIVA- LENT IN PERFORMANCE AND DURA- BILITY TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CONTROL SYSTEM AND MAY HAVE A BEARING ON THE OUT- COME OF THE WARRANTY CLAIM.

WARNING!

Before performing any mainte- nance, repair, or cleaning work on the unit, make sure the engine and cutting attachment are completely stopped.

Disconnect the spark plug wire before performing service or maintenance.

WARNING!

Non-standard accessories, cutting attachment, or replacement parts may not operate properly with your unit and may cause damage and lead to personal injury.

Muffler

WARNING!

Operating the engine without a muffler or with a muffler that is damaged or improperly installed can increase engine noise suf- ficiently to cause hearing loss.

This unit must never be operated with a faulty or missing muffler. Make sure the muffler is well secured and in good condi- tion. A worn or damaged muffler is a fire hazard and may also cause hearing loss.

Spark Plug

Keep the spark plug and wire connections tight and clean.

Daily Maintenance

Prior to each work day, perform the following:

■Remove all dirt and debris from the engine, check the cooling fins and air cleaner for clogging, and clean as necessary.

Keep cooling

fins clean.

Keep air

passages

clean.

10-Hour Maintenance

Every 10 hours of operation (more frequently in dusty or dirty conditions):

■Remove the air cleaner element from the air cleaner housing and clean it thoroughly with soap and water. Let it dry before reinstalling the element.

CAUTION!

Do not operate the unit if the air cleaner or element is damaged, or if the element is wet.

WARNING!

Always wear gloves when working around the cutter assembly.

■Carefully remove any accumulations of dirt or debris from the muffler and fuel tank. Check cooling air intake area at base of crankcase. Remove all debris. Dirt build-up in these areas can lead to engine overheating, fire, or premature wear.

■Clean any debris or dirt from the cutting attachment. Check the bar and chain for damage or incorrect adjustment.

■Check for loose or missing screws or components. Make sure the cutter attachment is securely fastened.

Loosen Knob

■Check the entire unit for leaking fuel or grease.

■Make sure nuts, bolts, and screws (except carburetor idle speed adjusting screws) are tight.

Remove and clean the

element.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents P231 Pole Pruner Introduction ContentsBeware of pinching Safety PrecautionsKickback and Pinching Beware of KickbackOperating Precautions Operating PrecautionsProperly Equipped Operator Safety Equipment and Labels Product Description Technical SpecificationsConnecting the Throttle Cable AssemblyPrior to assembly Powerhead InstallationAssembling tube sections Adjusting the Throttle CableKeep the open ends of the tubes clean and free of debris Connect The Throttle CableInstalling and Adjusting the Bar and Chain Installing the ChainDisassembling the tube sections Chain Oiler Adjusting the ChainAdjusting Oil Flow Rate Adjust the pump as followsAlways transport and store fuels in an approved container Mixing FuelFilling the Fuel Tank Minimize the risk of fire, burns, and personal injuryWhen the Engine Starts Starting the EngineNever start the engine from the operating position Adjusting the Engine Idle Check and Adjust Idle SpeedStopping the Engine Using the Pole Pruner Muffler General MaintenanceDaily Maintenance Hour Maintenance10/15-Hour Maintenance Clean or replace fuel filterEvery 10 to 15 hours of operation Long Term Storage MaintenanceMuffler maintenance Every 135 hours of operation, remove and clean the mufflerFor consistent filing angles, use a filing guide Sharpening the ChainWhat To Check Troubleshooting GuideSymptom Possible Cause Emission System Warranty Statement Fax Specifications subject to change without notice P231 Podadora de Extensión Índice Introducción Declaraciones de seguridadGuardarte de contragolpe Instrucciones generales de seguridadTrabaje con cuidado ¡ADVERTENCIA! Contragolpe y aprieteEl operario debidamente equipado Instrucciones de seguridadPrecauciones del funcionamiento Instrucciones de seguridad continuación Etiquetas de seguridadRealice siempre el mantenimiento Especificaciones Descripción del productoConexión del cable del acelerador EnsamblarAntes de Ensamblar Barras y cadenas opcionalesEnsamblar de las secciones del tubo Ensamblar continuaciónConecte el cable del acelerador Ajuste el cable del aceleradorInstalación y ajuste de la barra y la cadena de la sierra Desmontaje de las secciones del tuboInstalación la cadena Ajuste del flujo del aceite Adjuste la cadenaBomba de aceite Llenado del depósito de aceite¡ADVERTENCIA! Disminuya el riesgo de incendios Mezcla de combustibleLlenando el tanque de combustible Ejemplos de cantidades de mezcla a proporción deArranque del motor Nunca arranque el motor desde la posición de operaciónCuando arranca el motor… Continuar girando cuando se para El motor Parada del motorAjuste de marcha mínima del motor El accesorio de cortes pudoEl uso de la potadora de extensión Mantenimiento general Mantenimiento diarioCada 10 horas mantenimiento Mantenimiento continuación Cada 10 15 horas mantenimientoCada 50 horas mantenimiento Almacenamiento de largo plazo Mantenimiento del silenciadorCada 135 horas de operación, retire y limpie el silenciador Rendimiento de la cadena Para limar en ángulos iguales, use unaGuía para la lima Remedio Guía de localización de fallasQué revisar Posible causaQué revisar Posible causa Remedio Guía de localización de fallas continuaciónDeclaración de Garantía del Sistema de Emisión Notas Tronçonneuse à perche P231 De ce produit contiennent des sub Introduction Mises en gardeUnénoncéprécédédelamention Les échappements du moteurRéaliser les coupes à haut régime Consignes de sécuritéÉquipement complet de l’utilisateur Consignes d’utilisationNe pas utiliser l’appareil sans le silencieux Étiquettes et dispositifs de sécurité Consignes d’utilisation suiteCaractéristiques techniques NomenclatureRaccord du câble d’accélération Avant l’assemblageMontage de la tête motorisée Options du guide-chaîne et de la chaîneAssemblage les éléments du tube Assemblage suiteRaccorder le câble d’accélération Réglage du câble d’accélérationInstallation et réglage du guide-chaîne et de la chaîne Installation de la chaîneDésassemblage des éléments Réglage du débit d’huile Réglage de la chaîneHuileur de chaîne Remplissage du réservoir d’huileRemplissage du réservoir de carburant Mélange de carburantLorsque le moteur démarre Démarrage du moteurArrêt du moteur Réglage du ralenti du moteurVérification et réglage du ré- gime de ralenti Utilisation de la tronçonneuse Silencieux EntretienEntretien quotidien Entretien aux 10 heuresEntretien aux 50 heures Entretien suiteRemisage à long terme Entretien aux 10 à 15 heuresEnlever le capuchon de la bougie Entretien du pare-étincellesTechnique d’affûtage correcte Affûtage de la chaînePoints à contrôler SolutionPoints à contrôler Cause probable Solution Guide de dépannageCause probable Guide de dépannage suiteDéclaration de garantie du dispositif antipollution FR22 FR23 FR24

62891-94311 specifications

The Shindaiwa 62891-94311 is a premium combination of engineering and technology, designed for lawn care and landscaping professionals. This tool provides efficient and reliable performance, making it a top choice for outdoor enthusiasts and contractors alike. One of the standout features of the Shindaiwa 62891-94311 is its lightweight yet durable construction. This ensures that it delivers high performance without sacrificing user comfort, allowing operators to work for extended periods without undue fatigue.

This model is equipped with advanced engine technology that enhances fuel efficiency and reduces emissions. The 2-stroke engine not only delivers impressive power but also adheres to stringent environmental regulations. Users appreciate the reduced environmental footprint, which aligns with a growing trend towards sustainability in landscaping equipment.

Another key characteristic of the Shindaiwa 62891-94311 is its ergonomic design. The handle is designed for optimum comfort and control, reducing vibration during use, which leads to greater precision and reduces the risk of strain injuries. The combination of the lightweight structure and ergonomic grip allows for longer operational hours, ensuring that users can tackle large projects efficiently.

The product features easy-start technology, enabling quick and effortless ignition. This is particularly beneficial for professionals who need to maximize productivity on job sites. Additionally, the model includes an adjustable throttle, allowing users to easily adapt the power output according to their specific needs, whether it’s for trimming, edging, or heavy-duty cutting tasks.

Durability is another focus for the Shindaiwa 62891-94311. The materials used in its construction are engineered to withstand the rigors of outdoor use, ensuring longevity and reliability. This means that users can invest in this tool with confidence, knowing it can handle extensive workloads and still perform optimally.

In conclusion, the Shindaiwa 62891-94311 is a versatile and powerful tool that incorporates advanced technology, ergonomic design, and durability. It is an ideal choice for landscaping professionals seeking a reliable, efficient, and eco-friendly solution for their outdoor tasks. Whether trimming hedges or tackling tough underbrush, this model stands out as a preferred option in the field of outdoor power equipment.
Top Page Image Contents