Black & Decker LLP120 Chain tension adjustment, Replacing the chain and chain bar

Page 10

Installing / Removing Battery Pack WARNING: Make certain the lock-off button is engaged to

prevent switch actuation before removing or installing battery.

you check the tension of the chain, and chain retention bolts before

use and if required adjust.

Checking and adjusting the chain tension (figs. D, E)

To tension the chain slacken the

To install battery pack: Insert battery pack into tool until an audible click is heard (figure C).

To remove battery pack: Depress the battery release button in the back of the battery pack and pull battery pack out of tool.

C

two chain cover retention bolts

D

12

(11) with the wrench (12) and the

13 11

atuomatic chain tensioning device

 

(fig E) will push the chain bar

 

 

out, setting the correct tension.

 

 

Retighten the two retention bolts

 

 

(11) securely.

 

 

Check that the correct tension has

 

 

been set by lightly pulling on the

 

 

chain. The tension is correct when

 

 

the chain snaps back after being

 

 

pulled 1/8 inch (3 mm) away from

E

 

the guide bar. There should be no

 

“sag” between the guide bar and

 

 

chain on the underside.

 

 

Preparing AlLigator Lopper For Use WARNING: Read and understand all instructions. Failure to

follow all instructions listed below may result in electric shock, fire and/or serious personal injury

WARNING: Sharp moving blade. To prevent accidental operation, ensure that the battery is disconnected from the tool before performing the following operations. Failure to do this could result in serious personal injury.

CAUTION: Sharp moving blade. Always wear protective gloves when installing or removing the chain. The chain is sharp and can cut you when it is not running.

Chain tension adjustment

WARNING: Before chain or other adjustments, make sure that the battery is disconnected from the tool.

If the chain cannot be correctly tensioned, it may need to be replaced. Contact your nearest service center.

The product comes ready assembled. However we recommend that

Note: Do not over tension the chain

as this will lead to excessive wear

and reduce the life of the bar and

chain. It will also lead to reduced

product performance.

Note: With first use and when the chain is new, check tension

frequently as a new chain stretches slightly.

Replacing the chain and chain bar

After prolonged use the chain and / or chain bar may need

replacing. Use Black & Decker replacement chain RC600 only.

Low-Kickback saw chain is a chain which has met the kickback

performance requirements of ANSI B175.1 when tested on the

representative sample of chain saws.

Removing the saw chain & chain bar (figs. F, G)

WARNING: Before chain or other adjustments, make sure

that the battery is disconnected from the tool.

WARNING: Laceration hazard. Always wear protective gloves

when installing or removing the saw chain. The saw chain is sharp

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 20v max* lithium alligator lopper Table Of Contents Intended use Important Safety InstructionsUse Right Tool Use Safety GlassesDisconnect Battery Dress ProperlyAdditional safety instructions for AlligatorTM Lopper Power SupplyKickback Safety Features Electrical safetyBattery chargers SymbolsImportant safety instructions for Chain SAW Names and TermsComponents Important safety warnings For battery packs Read all InstructionsLeaving the battery in the charger Charging ProcedureImportant Charging Notes Replacing the chain and chain bar Chain tension adjustmentThat the battery is disconnected from the tool Removing the saw chain & chain bar figs. F, GAssembling the chain bar and chain figs. G, H OperationOiling fig Switching on and off fig. JSwitching on fig. K Trimming branchesMaintenance Service Information AccessoriesRbrc Seal Problem Possible Cause TroubleshootingTo shutoff abruptly when the charge is depleted See ‘Tools-Electric’ LImited two -year home use warrantyFor Service & Sales Yellow PagesNuméro de modèle Scies à chaîne Table DES MatièresUtilisation prÉvue Conserver la zone de travail propre’habiller de manière appropriée Ne pas forcer la scie à chaîneUtiliser l’outil approprié Porter des lunettes de sécuritéBloc d’alimentation Directives de sÉcuritÉ concernant l’effet de rebond ’ÉBRANCHEUR Sécurité en matière d’électricitéPage Composantes Directives de sÉcuritÉ importantes pour Les blocs-piles Conserver ces mesuresLire toutes les directives Procédure de charge Réglage de la tension de la chaîne Insertion et retrait du bloc-piles de l’outilAvertissement avant de régler la tension de la chaîne Risque de lacération. Toujours Remplacement de la chaîne et du guide-chaîneDébranchée de l’appareil Risque de brûlure. La barre duLubrification fig Assemblage de la chaîne et du guide chaîneFonctionnemenT Est débranchée de l’outilTaillage des branches EnTretienMise en marche fig. K Enlever les branches commeTransport NettoyageLubrification Affûtage de la chaîneRangement Accessoires Information sur les réparationsDEpannage Problème Cause possible Solution possibleMaximiser la durée de vie du Garantie limité de deux ans pour une Utilisation domestique Podadora Alligator CON Batería DE Litio DE 20 V MÁX Pautas DE SEGURIDAD/DEFINICIONES ÍndiceUso previsto Normas generales de seguridadVerifique que no haya piezas dañadas Desconecte la bateríaManténgase alerta Guarda contra retrocesosFuente de energía CaracterÍsticas de seguridad durante el Retroceso Nombres Y Términos DE LAS Sierras DE Cadena Componentes Descripción de las funciones fig. aAmperaje Lea todas las instrucciones Procedimiento de carga Notas importantes sobre la cargaAjuste de tensión de la cadena Desee, sin ningún efecto negativo sobre éstasRetiro de la cadena y de la barra de la sierra Verificación y ajuste de la tensión de la cadenaAdvertencia Riesgo de quemaduras. La barra de OperaciÓn Mantenimiento Encendido KRecorte de ramas Corte las ramas como seTransporte LimpiezaLubricación Afilado de la cadena de la sierraAccesorios AlmacenamientoEl sello Rbrc Page Solución posible ProblemaSolamente para Propósitos de México Page Page Esta Garantia no Aplica Cuando Gpo. Comercial de Htas. y Refacciones Grupo Realsa en herramientasPerfiles y Herramientas de Morelia Ferre Pat de Puebla, S.A. de C.V De Occidente, S.A. de C.V
Top Page Image Contents