Black & Decker LLP120 Additional safety instructions for AlligatorTM Lopper, Power Supply

Page 4

(8.) Never let the moving chain contact any object at the tip of the guide bar.

(9.) Keep the working area free from obstructions such as other trees, branches, rocks, fences, stumps, etc. Eliminate or avoid any obstruction that your saw chain could hit while you are cutting through a particular log or branch.

(10.) Keep your saw chain sharp and properly tensioned. A loose or dull chain can increase the chance of kickback. Check tension at regular intervals with the motor stopped and battery removed, never with the motor running.

(11.) Begin and continue cutting only with the chain moving at full speed. If the chain is moving at a slower speed, there is a greater chance for kickback to occur.

(12.) Cut one log at a time.

(13.) Use extreme caution when re-entering a previous cut. Engage ribbed bumpers into wood and allow chain to reach full speed before proceeding with cut.

(14.) Do not attempt plunge cuts or bore cuts.

(15.) Watch for shifting logs or other forces that could close a cut and pinch or fall into chain.

• Power Supply

Connect chain saw battery charger to correct voltage, that is, be sure that the voltage supplied is the same as that specified on the nameplate of the tool.

Additional safety instructions for the

AlligatorTM Lopper

WARNING: Never use the tool above shoulder height. Always position yourself out of the path of falling branches and debris.

WARNING: Do not use this tool to fell trees.

-Pre-plan a safe exit from falling branches and debris. Ensure the exit route is clear of obstacles that would prevent or hinder movement. Remember wet grass and freshly cut bark is slippery.

-Be aware of the direction that a branch may fall. Consider all conditions that may affect the direction of fall, including:

4

- The intended direction of fall. - The natural lean of the branch.

- Any unusual heavy limb structure or decay.

- Surrounding trees and obstacles including overhead lines. - The wind speed and direction.

- The safe distance between a branch and debris to be felled and bystanders, buildings and other objects is at least 2 1/2 times the length of the branch. Any bystander, building or object within this distance is at risk from being struck by the falling branch.

- When cutting a limb that is under tension be aware of spring back. When the tension in the wood fibres are released the spring loaded limb may strike the operator and/or throw the tool out of control.

- Always wear suitable safety equipment such as non-skid heavy-duty shoes, goggles, ear protection and gloves when operating the tool.

- Ensure someone is nearby (at a safe distance) in case of an accident. - Do not attempt to operate the tool when in a tree, on a ladder or standing on any other unstable support.

- Keep proper footing and balance at all times.

- Hold the tool firmly with both hands when the motor is running.

- Keep handles dry, clean and free from oil and grease. Greasy oily handles are slippery causing loss of control.

- Do not let the moving chain contact any object at the tip of the guide bar. - Keep your saw chain properly tensioned. Check tension at regular intervals with the motor stopped and battery disconnected.

- Begin and continue cutting only with the chain moving at full speed. - Watch for shifting branches or other forces that could close a cut and pinch or fall into the chain.

- Use extreme caution when re-entering a previous cut. Engage spikes on lower jaw into wood and allow the chain to reach full speed before proceeding with cut.

- Use of this tool for operation different to those intended could result in hazardous situations. Cut wood only. Don’t use this tool for purposes not intended - for example - Don’t use tool for cutting

Page 3 Page 5
Image 4
Page 3 Page 5
Contents 20v max* lithium alligator lopper Table Of Contents Intended use Important Safety InstructionsUse Safety Glasses Disconnect BatteryUse Right Tool Dress ProperlyAdditional safety instructions for AlligatorTM Lopper Power SupplyKickback Safety Features Electrical safetySymbols Important safety instructions forBattery chargers Chain SAW Names and TermsComponents Important safety warnings For battery packs Read all InstructionsLeaving the battery in the charger Charging ProcedureImportant Charging Notes Chain tension adjustment That the battery is disconnected from the toolReplacing the chain and chain bar Removing the saw chain & chain bar figs. F, GAssembling the chain bar and chain figs. G, H OperationSwitching on and off fig. J Switching on fig. KOiling fig Trimming branchesMaintenance Service Information AccessoriesRbrc Seal Problem Possible Cause TroubleshootingTo shutoff abruptly when the charge is depleted LImited two -year home use warranty For Service & SalesSee ‘Tools-Electric’ Yellow PagesNuméro de modèle Table DES Matières Utilisation prÉvueScies à chaîne Conserver la zone de travail propreNe pas forcer la scie à chaîne Utiliser l’outil approprié’habiller de manière appropriée Porter des lunettes de sécuritéBloc d’alimentation Directives de sÉcuritÉ concernant l’effet de rebond ’ÉBRANCHEUR Sécurité en matière d’électricitéPage Composantes Directives de sÉcuritÉ importantes pour Les blocs-piles Conserver ces mesuresLire toutes les directives Procédure de charge Réglage de la tension de la chaîne Insertion et retrait du bloc-piles de l’outilAvertissement avant de régler la tension de la chaîne Remplacement de la chaîne et du guide-chaîne Débranchée de l’appareilRisque de lacération. Toujours Risque de brûlure. La barre duAssemblage de la chaîne et du guide chaîne FonctionnemenTLubrification fig Est débranchée de l’outilEnTretien Mise en marche fig. KTaillage des branches Enlever les branches commeNettoyage LubrificationTransport Affûtage de la chaîneRangement Accessoires Information sur les réparationsDEpannage Problème Cause possible Solution possibleMaximiser la durée de vie du Garantie limité de deux ans pour une Utilisation domestique Podadora Alligator CON Batería DE Litio DE 20 V MÁX Pautas DE SEGURIDAD/DEFINICIONES ÍndiceUso previsto Normas generales de seguridadDesconecte la batería Manténgase alertaVerifique que no haya piezas dañadas Guarda contra retrocesosFuente de energía CaracterÍsticas de seguridad durante el Retroceso Nombres Y Términos DE LAS Sierras DE Cadena Componentes Descripción de las funciones fig. aAmperaje Lea todas las instrucciones Procedimiento de carga Notas importantes sobre la cargaAjuste de tensión de la cadena Desee, sin ningún efecto negativo sobre éstasRetiro de la cadena y de la barra de la sierra Verificación y ajuste de la tensión de la cadenaAdvertencia Riesgo de quemaduras. La barra de OperaciÓn Encendido K Recorte de ramasMantenimiento Corte las ramas como seLimpieza LubricaciónTransporte Afilado de la cadena de la sierraAccesorios AlmacenamientoEl sello Rbrc Page Solución posible ProblemaSolamente para Propósitos de México Page Page Esta Garantia no Aplica Cuando Grupo Realsa en herramientas Perfiles y Herramientas de MoreliaGpo. Comercial de Htas. y Refacciones Ferre Pat de Puebla, S.A. de C.V De Occidente, S.A. de C.V
Top Page Image Contents