Zebra Technologies 1050020011570 manuals
Computer Equipment > Printer
When we buy new device such as Zebra Technologies 1050020011570 we often through away most of the documentation but the warranty.
Very often issues with Zebra Technologies 1050020011570 begin only after the warranty period ends and you may want to find how to repair it or just do some service work.
Even oftener it is hard to remember what does each function in Printer Zebra Technologies 1050020011570 is responsible for and what options to choose for expected result.
Fortunately you can find all manuals for Printer on our side using links below.
Zebra Technologies 1050020011570 Manual
174 pages 4.19 Mb
1 User Guide2 © 2006 ZIH Corp(17 U.S.C.506). Copyright violators may be subject to civil liability Proprietary Statement Product Improvements Liability Disclaimer Limitation of Liability Part Number: 11342L-001Rev. A 3 Declaration of Conformity5 Contents9 About This Document15 Introduction23 Printer Setup37 Operations81 Configuration82 Setup Mode84 Change Password-ProtectedParametersDefault Password Value Disable the Password Protection Feature 85 Print a Configuration Label86 Print a Network Configuration Label87 Control Panel Parameters88 Table 9 • Printer Parameters (Page 2 of 19)Adjust the Tear-OffPosition TEAR OFF +000 Figure 24 • Tear-OffPosition Adjustment Default: +0 Range: Select Print Mode PRINT MODE -TEAR-OFF Default: TEAR-OFF Selections: 89 ^LLxxxx90 Table 9 • Printer Parameters (Page 4 of 19)Set Print Width PRINT WIDTH - MM 91 Set Maximum Label LengthMAXIMUM LENGTH -39.0IN 988 MM Figure 25 • Label Length 92 Table 9 • Printer Parameters (Page 6 of 19)List Fonts LIST FONTS PRINT List Bar Codes LIST BAR CODES List Images LIST IMAGES List Formats LIST FORMATS List Setup LIST SETUP List Network Settings LIST NETWORK 93 Table 9 • Printer Parameters (Page 7 of 19)List All LIST ALL This option prints labels that list the available fonts, bar codes, images formats, and the current printer and network configurations To print labels for all settings: Format Memory Card FORMAT CARD: This option erases all previously stored information from the optional PCMCIA card or Compact Flash card To format a memory card: 1.Press MINUS (-) to select A: or PLUS (+) to select B: Enter the password. For instructions, see Change Password-Protected Parameters ARE YOU SURE 4.Do you wish to continue •Press MINUS (-) to select NO to cancel the request and return to FORMAT CARD prompt prompt •Press PLUS (+) to select YES and begin initialization CHECKING B: MEMORY PRINTER IDLE 94 Table 9 • Printer Parameters (Page 8 of 19)Parameter Action/Explanation Initialize Flash Memory INIT FLASH MEM To initialize Flash memory: 1.Press PLUS (+) to select YES The display shows INITIALIZE FLASH 3.Press PLUS (+) to select YES The display shows ARE YOU SURE •Press MINUS (-) to select NO to cancel the request and return to the INITIALIZE FLASH prompt CHECKING E: MEMORY 95 Print Sensor ProfileSENSOR PROFILE Figure 26 • Sensor Profile 96 Table 9 • Printer Parameters (Page 10 of 19)Calibrate Media and Ribbon Sensor Sensitivity MEDIA AND RIBBON Use this procedure to adjust sensitivity of media and ribbon sensors CALIBRATE Important • Follow this procedure exactly as presented. All of the steps must be performed even if only one of the sensors requires adjustment. You may press MINUS (-) at any step in this procedure to cancel the process To perform a media and ribbon sensor calibration: LOAD BACKING 2.Open the printhead 4.Leave the printhead open 5.Press PLUS (+) to continue The REMOVE RIBBON prompt displays 6.Remove the ribbon (if used) 7.Close the printhead 8.Press PLUS (+) to continue The message CALIBRATING PLEASE WAIT displays The message displays When calibration is complete, RELOAD ALL displays 10.Reload the ribbon (if used) 11.Close the printhead 12.Press PLUS (+) to continue 97 Table 9 • Printer Parameters (Page 11 of 19)Set Parallel Communications PARALLEL COMM -BIDIRECTIONAL Set Serial Communications SERIAL COMM -RS232 Default: RS232 Set Baud BAUD Set Data Bits DATA BITS - 8 BITS Default: 8 BITS 98 Table 9 • Printer Parameters (Page 12 of 19)Set Parity PARITY Default: NONE Set Host Handshake HOST Default: XON/XOFF Set Protocol PROTOCOL ZEBRA ACK_NAK ZEBRA DTR/DSR Set Network ID NETWORK ID 99 Table 9 • Printer Parameters (Page 13 of 19)Set Communications Mode COMMUNICATIONS - NORMAL MODE Set Control Prefix Character CONTROL PREFIX >7EH Set Format Prefix Character FORMAT PREFIX <^>5EH 100 Table 9 • Printer Parameters (Page 14 of 19)Set Delimiter Character DELIMITER CHAR <,>2CH Select ZPL Mode ZPL MODE ZPL Default: ZPL Selections: ZPL II, ZPL Select Media Power-UpOption MEDIA POWER UP - CALIBRATION Feed Calibration Length Short Cal Motion 101 ~JS102 Table 9 • Printer Parameters (Page 16 of 19)Adjust Left Position LEFT POSITION ±0000 103 Table 9 • Printer Parameters (Page 17 of 19)Set the Printhead Resistor Value HEAD RESISTOR 0500 OHMS Initial Value: Default Value: Figure 27 • Head Resistance Value 104 Table 9 • Printer Parameters (Page 18 of 19)WEB S MEDIA S RIBBON S MARK S MARK MED S MEDIA LED RIBBON LED MARK LED Adjust LCD Display LCD ADJUST +10 Select Format Convert FORMAT CONVERT - NONE 105 Table 9 • Printer Parameters (Page 19 of 19)Set Real-TimeClock (RTC) Date RTC DATE 01/31/01 in IDLE DISPLAY Set RTC Time RTC TIME 14:55 Select the Display Language LANGUAGE ENGLISH Default: ENGLISH 106 Print Server LCD Displays107 ^WS108 ^WE109 Table 10 • Print Server Parameters (Page 4 of 4)Reset Network2,3 RESET NETWORK This option resets the wireless card and the print server when the wireless option is running. Selecting this option has no effect when the wireless option is not running, when there is no card inserted, or when the wireless password is anything other than the default (zero) 1. Press PLUS (+) to select YES The LCD prompts ARE YOU SURE 2. Do you wish to reset the network parameters • If no, press MINUS (–) to select NO and cancel the request • If yes, press PLUS (+) to select YES and reset the network 111 PC and Memory Cards115 Routine Maintenance125 Troubleshooting149 Specifications157 Glossary158 core diameterdiagnostics die-cut media direct thermal direct thermal media dynamic RAM fanfold media firmware FLASH memory Font ips (inches-per-second) label label backing (liner) liquid crystal display (LCD) 159 light emitting diode (LED)lock-up media sensor media supply hanger non-continuous non-volatile memory notched media peel-off print speed printhead wear registration ribbon ribbon wrinkle 160 roll mediafanfold media supplies A general term for media and ribbon symbology The term generally used when referring to a bar code tag tear-off thermal transfer direct thermal void 161 End User LicenseAgreement 167 Index
Also you can find more Zebra Technologies manuals or manuals for other Computer Equipment.