Manuals / Brands / Computer Equipment / Printer / Zebra Technologies / Computer Equipment / Printer

Zebra Technologies 1050020011570, 105SLTM, ZM40021014100T Control Panel LCD, Control Panel Buttons, Pause mode, Setup mode, Error mode, Operating mode, Table 1 • Control Panel Buttons

1 174

Download 174 pages, 4.19 Mb

10Introduction Control Panel

Control Panel LCD

The control panel LCD functions differently in different printer modes.

•In Operating mode, the LCD displays the printer’s status, sometimes in conjunction with a control panel light (see Control Panel Lights on page 11).

•In Pause mode, the printer stops printing temporarily.

•In Setup mode, you can use the control panel LCD to view or modify printer parameters (see Control Panel Parameters on page 79).

•In Error mode, the LCD may display an alert or error message (see LCD Error Messages on page 119).

Control Panel Buttons

	Table 1 describes the function of each button.
		Table 1 • Control Panel Buttons

Button	Appearance	Function

PAUSE		Stops and restarts the printing process or removes error messages and
		clears the LCD.
		• If the printer is idle, it enters Pause mode immediately.
		• If the printer is printing, the label is completed before the printer pauses.

FEED		Advances a blank label.
		• If the printer is idle or paused, the label is fed immediately.
		• If the printer is printing, the label is fed after printing finishes.

CANCEL		CANCEL functions only in Pause mode. Pressing CANCEL once has these
		effects:
		• Cancels the label format that is currently printing.
		• If no label format is printing, the next one to be printed is canceled.
		• If no label formats are waiting to be printed, CANCEL is ignored.
		To clear the printer’s entire label format memory, press and hold CANCEL.
		When the formats are cleared, the DATA light turns off.

PREVIOUS		When in Setup mode, scrolls the LCD to the previous parameter. Press and
		hold to scroll quickly.

NEXT/SAVE		• When in Setup mode, scrolls the LCD to the next parameter. Press and
		hold to scroll quickly.
		• When exiting Setup mode, saves any changes you have made in the
		configuration and calibration sequence.

SETUP/EXIT		Enters and exits Setup mode.

11342L-001 Rev. A

105SL User Guide

6/30/06

Contents

User Guide © 2006 ZIH Corp (17 U.S.C.506). Copyright violators may be subject to civil liability Proprietary Statement Product Improvements Liability Disclaimer Declaration of Conformity Compliance Information FCC Compliance Statement Canadian DOC Compliance Statement Contents Page Page Page About This Document Who Should Use This Document How This Document Is Organized Contacts Web Site The Americas Europe, Africa, Middle East, and India Asia Pacific Document Conventions ZTools bin Illustration Callouts Figure 1 • Sample Figure with Callouts Page Introduction External View Control Panel Control Panel LCD Control Panel Buttons Control Panel Lights Table 2 • Control Panel Lights (Continued) Printer Media Compartment Page Printer Setup Before You Begin Handling the Printer Unpack and Inspect the Printer Store the Printer Ship the Printer Recycle the Printer Select a Site for the Printer Select a Surface Provide Proper Operating Conditions Allow Proper Space Provide a Data Source Select a Communication Interface Connector Locations Types of Connections IEEE 1284 Bidirectional Parallel Figure 7 • Connecting the Printer through the Parallel Port Data Cable Requirements Connect the Printer to a Power Source Power Cord Specifications Types of Media Table 5 • Types of Media (Continued) Fanfold Media Continuous Ribbon Overview When to Use Ribbon Coated Side of Ribbon Adhesive Test To perform an adhesive test, complete these steps: outer inner Ribbon Scratch Test Operations Media Loading Overview Print Modes Insert Media into the Printer Fanfold Media To load fanfold media, complete these steps: Figure 15 • Rear Feed Using Media Supply Hanger Figure 16 • Bottom Feed Without Using Media Supply Hanger Page Load Media in Tear-OffMode Page Page Page Load Media in Peel-OffMode To load media in Peel-Offmode, complete these steps: Page Page Page Page Page Page Page Remove Media Liner from the Rewind or Peel Spindle Page Load Media in Rewind Mode To load media in Rewind mode, complete these steps: Page Page Page Page Remove Labels from the Rewind Spindle Page Load Media in Cutter Mode Page Page Page Load Ribbon Page Page Page Remove Used Ribbon Adjust Media Sensors Black Mark Sensor Transmissive Sensor Lower Media Sensor To adjust the lower media sensor, complete these steps: Adjust Printhead Balance and Pressure Adjust Printhead Balance Page Printhead Pressure Adjustment Calibrate the Printer Table 7 • Types of Calibration (Continued) Media and Ribbon Sensor Sensitivity Calibration Configuration Setup Mode Enter Setup Mode Exit Setup Mode Change Password-ProtectedParameters Default Password Value Disable the Password Protection Feature ^KP ^KPx Print a Configuration Label Print a Network Configuration Label Control Panel Parameters Table 9 • Printer Parameters (Page 2 of 19) Adjust the Tear-OffPosition TEAR OFF +000 Figure 24 • Tear-OffPosition Adjustment ^LLxxxx Table 9 • Printer Parameters (Page 4 of 19) Set Print Width PRINT WIDTH - MM Set Maximum Label Length MAXIMUM LENGTH -39.0IN 988 MM Figure 25 • Label Length Table 9 • Printer Parameters (Page 6 of 19) List Fonts LIST FONTS PRINT List Bar Codes Table 9 • Printer Parameters (Page 7 of 19) List All LIST ALL This option prints labels that list the available fonts, bar codes, images formats, and the current printer and network configurations Table 9 • Printer Parameters (Page 8 of 19) Parameter Action/Explanation Initialize Flash Memory INIT FLASH MEM To initialize Flash memory: Print Sensor Profile SENSOR PROFILE Figure 26 • Sensor Profile Table 9 • Printer Parameters (Page 10 of 19) Calibrate Media and Ribbon Sensor Sensitivity MEDIA AND RIBBON Use this procedure to adjust sensitivity of media and ribbon sensors CALIBRATE Table 9 • Printer Parameters (Page 11 of 19) Set Parallel Communications PARALLEL COMM -BIDIRECTIONAL Set Serial Communications Table 9 • Printer Parameters (Page 12 of 19) Set Parity PARITY Default: NONE Set Host Handshake Table 9 • Printer Parameters (Page 13 of 19) Set Communications Mode COMMUNICATIONS - NORMAL MODE Set Control Prefix Character Table 9 • Printer Parameters (Page 14 of 19) Set Delimiter Character DELIMITER CHAR <,>2CH Select ZPL Mode ~JS Table 9 • Printer Parameters (Page 16 of 19) Adjust Left Position LEFT POSITION ±0000 Table 9 • Printer Parameters (Page 17 of 19) Set the Printhead Resistor Value HEAD RESISTOR 0500 OHMS Initial Value: Table 9 • Printer Parameters (Page 18 of 19) WEB S MEDIA S RIBBON S MARK S Table 9 • Printer Parameters (Page 19 of 19) Set Real-TimeClock (RTC) Date RTC DATE 01/31/01 in IDLE DISPLAY Print Server LCD Displays ^WS ^WE Table 10 • Print Server Parameters (Page 4 of 4) Reset Network2,3 RESET NETWORK This option resets the wireless card and the print server when the wireless option is running. Selecting this option has no effect when the wireless Page PC and Memory Cards PCMCIA PC Cards Page Page Routine Maintenance Lubrication Cleaning Schedule Clean the Exterior Clean the Printhead and Platen Roller Figure 29 • Printhead and Platen Roller Cleaning Page Clean the Media Compartment and Sensors Figure 32 • Take-LabelSensors, Black Mark Sensor, and Ribbon Sensor Clean the Snap Plate Clean the Cutter Replace the Fuse Troubleshooting Troubleshooting Checklists LCD Error Messages Table 12 • LCD Error Messages (Continued) RIBBON IN (function) Print Quality Problems Table 13 • Print Quality Problems (Continued) Fine, angular gray lines on blank labels Printing too light or too dark over the Vertical drift in top-of-formposition Vertical image or label drift The bar code printed Calibration Problems Communications Problems ^CC ^CT ^CD Ribbon Problems Miscellaneous Printer Problems Table 17 • Miscellaneous Printer Problems (Continued) The printer fails to calibrate or detect the top of the label Non-continuous Printer Diagnostics Power-OnSelf Test CANCEL Self Test Page PAUSE Self Test FEED Self Test Figure 36 • FEED Test Label Figure 37 • Bar Code Darkness Comparison Table 18 • Judging Bar Code Quality Too dark Slightly dark Table 18 • Judging Bar Code Quality (Continued) “In-spec” Slightly light Too light FEED and PAUSE Self Test Communications Diagnostics Test Sensor Profile Specifications General Specifications Physical Environmental Conditions for Operation and Storage Electrical Specifications Communications Specifications Other Standard Features Additional Options Agency Approvals Printing Specifications Ribbon Specifications Media Specifications Zebra Programming Language (ZPL II) Bar Codes Page Glossary core diameter diagnostics die-cut media direct thermal light emitting diode (LED) lock-up media sensor media supply hanger non-continuous roll media fanfold media supplies A general term for media and ribbon symbology The term generally used when referring to a bar code tag End User License Agreement Documentation Limitations of Reverse Engineering, Decompilation and Disassembly Transfer/Sublicense Confidentiality Intellectual Property Export Restrictions Accessing Services Using the Software Disclaimer Limitation of Liability and Damages Zebra Suppliers and Licensors Governing Law Injunctive Relief Entire Agreement Assignment Modification Waiver Page Index HEAD COLD HEAD TOO HOT OUT OF MEMORY message PAPER OUT RIBBON IN RIBBON OUT Page Page Zebra Technologies Europe Limited Zebra Technologies Asia Pacific, LLC Part Number: 11342L-001Rev. A © 2006 ZIH Corp