Menus, Terminal Emulator | 3Com DSA-3CV1001-02 specs

38CHAPTER 4: USING THE LOCAL MANAGEMENT ACCESS

Connecting the PC Perform the steps below to connect the PC to the LMA port:

Terminal Emulator

1Remove the cover from the LMA section of the VCN AP as in the figure below.

Figure 27 LMA Section of the VCN Access Point

Screw hole

E TH E RN E T

Fax-M odem

Lin e

P o w e r

Local

Management Port

2Connect the LMA port to the PC serial port (COM1 or 2) with the cable provided you; if you do not have the cable, contact 3Com. Plug the end of the cable with the a four-pin MiniDIN connector into the VCN AP LMA port.

VCN Access Point This section describes the menus.

Menus

Summary and This section provides a menu hierarchy to describe the structure of the Structure of the menu system and a menu summary to help the network administrator

Menus use the management system efficiently.

The chart in Figure 28 summarizes the menu hierarchy. The abbreviations next to the menu names are suggestions for how the menus are used. Most of the menus labeled D are not described further in this chapter since they are used mainly by developers for debugging. The debug menus for performing loopbacks are described since loopbacks can be used by network administrators to solve problems.

Image 38

3Com DSA-3CV1001-02 service manual Terminal Emulator, Menus use the management system efficiently

Contents

Visitor and Community Network Access Point 3Com Corporation 5400 Bayfront Plaza Santa Clara, California List conventions that are used throughout this guide About this GuideConventions Icon Description Year RelatedDocumentation Compliance Contents Using the Local Management Access Summary and Structure of the Menus Login Online Technical Services World Wide Web Site 3Com FTP SitePage Visitor Features BenefitsOverview Community Overview Visitor Community Network Applications Shows a typical MTU/MDU application Features PBX VCN AP Software Download Network Configuration Type State Used to Describes the LEDs and connectors on the front panelVCN Access Point LEDs and Connectors Front View Describes the connectors on the back panel VCN AP Unit LEDs and Connectors Back Panel Safety Information To reduce the risk of electrocution and fire Précautions de sécurité concernant le VCN Access Point Sicherheitsvorkeh- rungen für den VCN Access Point Sicherheitsvorkehrungen für den VCN Access Point Safety Information Quantity Supplied by Installing and Operating VCN Access PointUnpacking List 3Com Wall, see Installing the VCNAccess Point Under a table, see Access Point on a Wall Apply the paper template to the wall as shown in Figure Insert the three anchors. See Figure Drill Holes for Anchors Inserting Anchors Drive the last screw into the wall anchor to the full depth Screw Holes in the Top of the VCN AP Table the lower surface of a table, as in Figure VCN AP without Curved Cover Ap er tem pla te Lin e W e r Is aligned with the VCN APs small screw hole. See Figure Driving Two Screws into the Table Inserting the VCN AP under the Table Completion of Mounting the VCN AP Under the Table Preparing VCN AP for Table Top Use Troubleshooting, section Power-on Self Test Post Making a Voice Call Operating the VCNVCN AP may be used for the following Any front panel connection Receiving Data Traffic Receiving Faxes Management Using the Local Management AccessUsing Terminal Menus use the management system efficiently MenusTerminal Emulator Menu Hierarchy Number Sequence Corresponding to Submenus Type your Login ID and press EnterType your password and press Enter Return to Previous Menu Option VCN AP Main Menu Version Screen VCN AP Management Menu Ethernet Traffic Counters Ethernet Status Ethernet Traffic Count Screen Learning Table Reset CountersChange Ethernet Work Mode Menu If a PC is not connected, the message in appears Setting Internal Loopback Mode When you discard the operation, the message appears Setting External Loopback Mode Hdlc Menu To view the Hdlc Menu Hdlc Traffic Counters Type y and press Enter to perform the reset Hdlc Status Change Hdlc Work Mode Hdlc Status Screen Normal mode is lack of loopbacks Operation Mode Selector Menu appears Reset messages Enter F Vdsl QAM Channel Status Report Set Vlan ID for Management To set the Vlan ID perform the following steps Change Password Set Ethernet Half/Full Duplex ModeEnter the desired mode a confirmation message appears To change the password, do as follows Set to Factory Defaults Interface from the Local Management port Download Access in this manualProcedure VCN Service Switch 10 Front Pane Downloading Software to the LCs in the VCN AC Software Download Network Configuration Software Download Menu Enter the AC Vlan ID and press Enter. The message appears LC Downloading State Table LC Downloading Results Downloading Software to VCN APs Enter the AP Vlan ID and press Enter. The message appears AP Downloading State Table Check Software Download for the LC Cards Download Failed for all LCs and all VCN APs Download Failed for One or More Line Cards but not All Download Failed for One or More VCN APs but not All Use the front panel LEDs to determine each port’s status TroubleshootingState Ethernet Line Power Determining VCN AP Status During Post VCN AP LEDs ProblemsDescribes the LEDs State Indicates VCN AP is not VCN AP VCN AC Problem Solution Summary of VCN AP LED Indications after Post NIC Summary Abnormal Indications From Traffic Counts Hdlc Traffic Count IndicatorsSummary of Problems Indicated by Counts of Errored Frames Counter Counts the Frames Normal Count Indicates Fatal Error Messages Error message Significance User Action Appendix a Troubleshooting Product Specification EMC Appendix B Product Specification Local Access Confirm Reset Board Management Menu appears Type Y to reset. The screen in appears Type S the downloading message appears Figure Procomm window , select Data Send File Figure Procomm Plus Terminal Screen Screen in appears Select the correct file and click Open While the file is downloading, the status window in appears Send File Status Window Flash VCN AP Pin No. Assignment LM Terminal Connector Pin AssignmentPIN Assignments for LMA D Cable VCN AP describes the pin assignments LM Cable Wiring LM Cable Connections MiniDIN DB-9 Pin No Pin No. Assignment Appendix D PIN Assignments for LMA Cable To define the terminal emulation settings Terminal Emulation SettingsTerminal Emulation Settings Defining Terminal settings can be established in one of two ways Terminal SettingsConfiguration Bar Procomm Plus Settings Procomm Setup Window No From Left Function Settings Flow control Connection Properties Window Technical Support ServicesServices Online Technical Hours a day, 7 days a week Access by Analog ModemUsername anonymous Country Data Rate Telephone Number 408 727 Access by Digital Modem847 262 Europe, South Africa, and Middle East Country Telephone Number Asia, Pacific Rim Country Telephone Number Fax Number Page Index Numbers Remote software download Requirements 3Com Corporation Limited Warranty Obtaining Warranty Service Ninety 90 days Governing LAW EMC Statements