Installing the VCN, Access Point, Wall, see | 3Com DSA-3CV1001-02

22CHAPTER 3: INSTALLING AND OPERATING THE VCN ACCESS POINT

Table 5 Unpacking List (continued)

NO.	Item	Quantity	Supplied by

3	ac/dc adapter	1	3Com
4	Line cable (RJ-11)	1	3Com
5	Laptop/PC cable (RJ-45)	1	End User or Customer on Request
6	FAX cable (RJ-11)	1	End User or Customer on Request
7	4-pin MiniDIN Control	1	3Com, for Local Management or
	Cable		Troubleshooting Only
8	Long screws1	3	3Com
9	Short screws1,2	3	3Com.
10	Wall anchors1	3	3Com
11	Template2	1	3Com, for Installation only
12	Rubber pads3	4	3Com

1For VCN AP wall installation

2For installing VCN AP under the table

3For VCN AP table top installation

The VCN AC must be installed before the VCN AP. Refer to the Visitor and Community Based Networking Concentrator Unit Service Manual.

Installing the VCN	The VCN AP may be conveniently mounted on one the following:
Access Point	■ a wall, see page 23.
	■ a wall, see page 23.
	■	under a table, see page 27.
	■	on top of a table, see page 32.

Image 22

3Com DSA-3CV1001-02 service manual Installing the VCN, Access Point, Wall, see, Under a table, see, On top of a table, see

Contents

Visitor and Community Network Access Point 3Com Corporation 5400 Bayfront Plaza Santa Clara, California List conventions that are used throughout this guide About this GuideConventions Icon Description Year RelatedDocumentation Compliance Contents Using the Local Management Access Summary and Structure of the Menus Login Online Technical Services World Wide Web Site 3Com FTP SitePage Visitor Features BenefitsOverview Community Overview Visitor Community Network Applications Shows a typical MTU/MDU application Features PBX VCN AP Software Download Network Configuration VCN Access Point LEDs and Connectors Front View Describes the LEDs and connectors on the front panelType State Used to Describes the connectors on the back panel VCN AP Unit LEDs and Connectors Back Panel Safety Information To reduce the risk of electrocution and fire Précautions de sécurité concernant le VCN Access Point Sicherheitsvorkeh- rungen für den VCN Access Point Sicherheitsvorkehrungen für den VCN Access Point Safety Information Quantity Supplied by Installing and Operating VCN Access PointUnpacking List 3Com Wall, see Installing the VCNAccess Point Under a table, see Access Point on a Wall Apply the paper template to the wall as shown in Figure Insert the three anchors. See Figure Drill Holes for Anchors Inserting Anchors Drive the last screw into the wall anchor to the full depth Screw Holes in the Top of the VCN AP Table the lower surface of a table, as in Figure VCN AP without Curved Cover Ap er tem pla te Lin e W e r Is aligned with the VCN APs small screw hole. See Figure Driving Two Screws into the Table Inserting the VCN AP under the Table Completion of Mounting the VCN AP Under the Table Preparing VCN AP for Table Top Use Troubleshooting, section Power-on Self Test Post Making a Voice Call Operating the VCNVCN AP may be used for the following Any front panel connection Receiving Data Traffic Receiving Faxes Management Using the Local Management AccessUsing Terminal Terminal Emulator MenusMenus use the management system efficiently Menu Hierarchy Type your password and press Enter Type your Login ID and press EnterNumber Sequence Corresponding to Submenus Return to Previous Menu Option VCN AP Main Menu Version Screen VCN AP Management Menu Ethernet Traffic Counters Ethernet Status Ethernet Traffic Count Screen Learning Table Reset CountersChange Ethernet Work Mode Menu If a PC is not connected, the message in appears Setting Internal Loopback Mode When you discard the operation, the message appears Setting External Loopback Mode Hdlc Menu To view the Hdlc Menu Hdlc Traffic Counters Type y and press Enter to perform the reset Hdlc Status Change Hdlc Work Mode Hdlc Status Screen Normal mode is lack of loopbacks Operation Mode Selector Menu appears Reset messages Enter F Vdsl QAM Channel Status Report Set Vlan ID for Management To set the Vlan ID perform the following steps Change Password Set Ethernet Half/Full Duplex ModeEnter the desired mode a confirmation message appears To change the password, do as follows Set to Factory Defaults Interface from the Local Management port Procedure Access in this manualDownload VCN Service Switch 10 Front Pane Downloading Software to the LCs in the VCN AC Software Download Network Configuration Software Download Menu Enter the AC Vlan ID and press Enter. The message appears LC Downloading State Table LC Downloading Results Downloading Software to VCN APs Enter the AP Vlan ID and press Enter. The message appears AP Downloading State Table Check Software Download for the LC Cards Download Failed for all LCs and all VCN APs Download Failed for One or More Line Cards but not All Download Failed for One or More VCN APs but not All Use the front panel LEDs to determine each port’s status TroubleshootingState Ethernet Line Power Determining VCN AP Status During Post VCN AP LEDs ProblemsDescribes the LEDs State Indicates VCN AP is not VCN AP VCN AC Problem Solution Summary of VCN AP LED Indications after Post NIC Summary Abnormal Indications From Traffic Counts Hdlc Traffic Count IndicatorsSummary of Problems Indicated by Counts of Errored Frames Counter Counts the Frames Normal Count Indicates Fatal Error Messages Error message Significance User Action Appendix a Troubleshooting Product Specification EMC Appendix B Product Specification Local Access Confirm Reset Board Management Menu appears Type Y to reset. The screen in appears Type S the downloading message appears Figure Procomm window , select Data Send File Figure Procomm Plus Terminal Screen Screen in appears Select the correct file and click Open While the file is downloading, the status window in appears Send File Status Window Flash VCN AP PIN Assignments for LMA D Cable LM Terminal Connector Pin AssignmentPin No. Assignment VCN AP describes the pin assignments LM Cable Wiring LM Cable Connections MiniDIN DB-9 Pin No Pin No. Assignment Appendix D PIN Assignments for LMA Cable To define the terminal emulation settings Terminal Emulation SettingsTerminal Emulation Settings Defining Terminal settings can be established in one of two ways Terminal SettingsConfiguration Bar Procomm Plus Settings Procomm Setup Window No From Left Function Settings Flow control Connection Properties Window Technical Support ServicesServices Online Technical Hours a day, 7 days a week Access by Analog ModemUsername anonymous Country Data Rate Telephone Number 847 262 Access by Digital Modem408 727 Europe, South Africa, and Middle East Country Telephone Number Asia, Pacific Rim Country Telephone Number Fax Number Page Index Numbers Remote software download Requirements 3Com Corporation Limited Warranty Obtaining Warranty Service Ninety 90 days Governing LAW EMC Statements