FIC-8T1 panel, LEDs on FIC-8T1 and FIC-8T1-F panels | 3Com MSR 30

		FIC-8T1/FIC-8T1-F 177
Table 120 LEDs on the FIC-8T1 and FIC-8T1-F panels

Attribute	Description

Operating mode	CT1, ISDN PRI (only supported by the
	FIC-8T1)
	FT1 (only supported by the FIC-8T1-F)
Supported service	1)	Backup
	2)	Terminal access service
	3)	ISDN PRI (supported by the FIC-8T1)

Interface LEDs FIC-8T1 and FIC-8T1-F panels look the same. The following figure illustrates a FIC-8T1 panel.

Figure 219 FIC-8T1 panel

The following table describes the LEDs on the card panels:

Table 121 LEDs on FIC-8T1 and FIC-8T1-F panels

LED	Description

LINK	OFF means no link is present; ON means a
	link is present.
ACTIVE	OFF means no data is being transmitted or
	received. ON means data is being
	transmitted and/or received.

Interface Cable The following figure illustrates the 8T1 conversion cable for the FIC-8T1/FIC-8T1-F card.

Figure 220 8T1 conversion cable

Image 177

3Com MSR 30, MSR 20, MSR 50 manual FIC-8T1 panel, LEDs on FIC-8T1 and FIC-8T1-F panels

Contents

H3C MSR 20/30/50 Series Routers United States Government Legend 3Com Corporation Campus Drive Marlborough, MA USA Contents FIC-8ASE/FIC-16ASE 143161 FIC-8E1/FIC-8E1-F SIC/DSIC Purchase Guide 235 Ande Module 229 Snde Module 230 Vcpm Module 231236 FIC/DFIC Purchase Guide 238 ESM/VPM/VCPM Purchase GuidePage Lists text conventions that are used throughout this guide Lists icon conventions that are used throughout this guideText Conventions Convention Description Documentation Related SIC/DSIC Interface CardsWAN interface cards Overview MIM/DMIM/XMIM Overview FIC/DFIC Interface RoutersPort 10Base-T/100Base-TX FE interface card FIC-4FE Overview Guideline SIC/MIM/FIC PurchaseVoice interface cards Encryption cards Installing a SIC Installation/Removal A SIC/MIM/FICTools required Flat-module screwdriver Installing/Removing a Installing a MIMRemoving a SIC Removing a MIM Installing a MIM Operation by using the undo remove slot command Execute the undo remove slot command howeverRepeat these steps to install all the other FICs Command Overview So on SIC-1FEARouter Or slot LED Description of the LEDs on SIC-1FEA panelLink ACT Interface attributes of the SIC-1SAE SIC-1SAEDescription Attribute Synchronous Asynchronous DTE, DCE LEDs on SIC-1SAE panel SIC-1SAE panel DTE cable DCE cable RS449 DCE cable RS449 DTE cable RS530 DCE cable RS530 DTE cable SIC-1EPRI/SIC-1E1-F Interface attributes of SIC-1EPRI/SIC-1E1-FAttribute Description 120-ohm DIP switch Description Ohm impedance Impedance SIC-1EPRI panel is shown in the following figure Interface LEDsSIC-1E1-F panel is shown in the following figure Description of the LEDs on SIC-1EPRI/SIC-1E1-F panel Connecting the Interface Cable SIC-1EPRI/SIC-1E1-F. By default, they are not suppliedBalanced twisted pair cables Addition, a 75-ohm to 120-ohm adapter is available Marked TX Interface attributes of SIC-1TPRI/SIC-1T1-F SIC-1TPRI/SIC-1T1-F SIC-1T1-F panel SIC-1TPRI panel Description of the LEDs on SIC-1TPRI/SIC-1T1-F panel Default, they are not supplied SIC-1AM/SIC-2AM Interface LEDs SIC-1AM panelInterface attributes of SIC-1AM/SIC-2AM Low-End and Mid-Range Series Routers Cable Manual SIC-1FXS/SIC-1FXO SIC-2FXS/SIC-2FXO SIC-2FXS/SIC-2FXO panel Interface LEDs SIC-1FXS/SIC-1FXO panelSIC-1FXS/SIC-1FXO SIC-2FXS/SIC-2FXO DSIC-9FSW/DSIC-9FS SIC-4FSW/SIC-4FSW-PoPoE SIC-2FXS/SIC-2FXO includes a ferrite core telephone cable MDI/MDIX Interface Attributes To a Hub or LAN Switch using a straight-through cable CableLEDs on the panel Interface Attributes of the SIC-1GEC SIC-1GECMaximum SFP SIC-1GEC panel Connecting Ethernet electrical interface cable Connecting Ethernet fiber interface cable Configure a VPM based on voice traffic SignalsSIC-1VE1 Card Configuration Description of DIP switch settings of SIC-ERRI/SIC-1E1-FDIP Description Ohm impedance SIC-1VE1 panel Following table describes the LEDs on the SIC-1VE1 panel SIC-1VE1. By default, they are not supplied SIC-1VT1 Following table describes the LEDs on the SIC-1VT1 panel Interface Attributes of the SIC-1T1-FDescription on SIC-1VT1 LED SIC-1ADSL SIC-1ADSL delivers these features Following table describes the LEDs on the card panel Interface attributes of the SIC-1ADSLSIC-1ADSL SIC-1ADSL-I Connecting the SIC-1ADSL Interface attributes of the SIC-1ADSL-I LEDs on the SIC-1ADSL-I panel1ADSL-I Connect the SIC-1ADSL-I SIC-1BS/SIC-2BS&SIC-1 BU/SIC-2BU SIC-1BS/SIC-2BS RJ45 Interface attributes of SIC-1BS/SIC-2BS and SIC-1BU/SIC-2BU LEDs on SIC-1BS/SIC-2BS and SIC-1BU/SIC-2BU panels SIC-1BSV/SIC-2BSV Interface attributes of SIC-1BSV/SIC-2BSV Following figure illustrates the SIC-2BSV panelLEDs on SIC-1BSV/SIC-2BSV panel SIC-1BSV SIC-2BSV Crossover Isdn S/T cable Straight-through Isdn S/T cable SFP/LC SIC-1FEF Following table describes the LEDs on the SIC-1FEF panel Press the button on the connector to remove itLEDs on SIC-1FEF panel Status Description Interface attributes of SIC-8AS SIC-8AS Following table describes the LEDs on the SIC-8AS panel LEDs on SIC-8AS panelLINK/ACT Customized cable Smart Interface Cards 4FE Modules MIM-1FE/MIM-2FE/MIInterface attributes of MIM-1FE/MIM-2FE/MIM-4FE MIM-1FE MIM-2FE MIM-4FE MIM-4FE panel is shown in the following figure MIM-2FE panel is shown in the following figureInterface Cable Ethernet cable Active MIM-1GBE/MIM-2GBE ModuleMaking Ethernet cable Description of the LEDs on the MIM-1GBE/MIM-2GBE panel Interface attributes of MIM-1GBE/MIM-2GBEDescription Attribute MIM-1GBE MIM-2GBE Cable Manual MIM-1GEF/MIM-2GEFInterface attributes of MIM-1GEF/MIM-2GEF MIM-1GEF MIM-2GEF MIM-2GEF panel MIM-1GEF panel Are not provided By Lucent MIM-2SAE/MIM-4SAE MIM-8SAE ModuleInterface attributes of MIM-2SAE/MIM-4SAE/MIM-8SAE MIM-4SAE panel is shown in the following figure MIM-8SAE panel is shown in the following figureDescription of the LEDs on the MIM-2SAE/MIM-4SAE panel 24 DTE cable RS449 DTE cable Connecting the Interface Cable MIM-8ASE/MIM-16AS Interface attributes of MIM-8ASE/MIM-16ASEDescription Attribute MIM-8ASE module MIM-16ASE module MIM-16ASE panel is shown in the following figure Mid-Range Series Routers Cable ManualRemoval tends to damage the module and even the device MIM-1E1/MIM-2E1/MI E1-F modules do not support PRI mode4E1/MIM-1E1-F/MI 2E1-F/MIM-4E1-F Modules Introduction MIM-1E1/MIM-2E1/MIM-4E1 MIM-1E1 panel E1 120-ohm balanced twisted pair cable E1 75-ohm unbalanced coaxial cable 120-ohm 4E1 conversion cable Conversion cable for MIM-4E1/MIM-4E1-F module Module MIM-1E1/1E1-F MIM-2E1/2E1-F MIM-4E1/4E1-F See Low-End and Mid-Range Series Routers Cable Manual DIP Local Rx wire to the remote Tx wire Connecting interface cable of MIM-4E1/MIM-4E1-F Introduction MIM-8E1 module MIM-8E1/MIM-8E1-FMIM-8E1-F module Interface attributes of the MIM-8E1 and the MIM-8E1-F Description of the LEDs on the MIM-8E1/MIM-8E1-F panel MIM-8E1 120-ohm panel MIM-1T1/MIM-2T1/MI 4T1/MIM-1T1-F/MI 2T1-F/MIM-4T1-F ModulesIntroduction MIM-1T1/MIM-2T1/MIM-4T1 module FT1 CT1, Isdn PRI LP/AL MIM-1T1 panel Extending a T1 cable Introduction MIM-8T1 module MIM-8T1/MIM-8T1-FMIM-8T1-F module Interface attributes of the MIM-8T1 and the MIM-8T1-F Description of the LEDs on the MIM-8T1/MIM-8T1-F panel MIM-8T1 panel Smaller than or equal to 128, when working in CE3 mode Accessing of E3 traffic when working in E3 modeMIM-1CE3 Module E2-to-E1 demultiplex. E23 and E12 discussed here represent Description of the LEDs on the MIM-1CE3 panel MIM-1CT3 Module MIM-1CT3 panel is shown in the following figure Accessing of T3 traffic when working in T3 modeFollowing table describes the LEDs on the MIM-1CT3 panel Interface attributes of MIM-1CT3 MIM-4BSE Module Description of the LEDs on the MIM-1CT3 panelInterface attributes of the MIM-4BSE Jumper settings of the MIM-4BSE example Following table describes how to set jumpers Set the jumpers on the MIM-4BSE Jumper settings & description Default LEDs on the MIM-4BSE panel Following table describes the LEDs on the module panel MIM-1G.SHDSL Interface attributes of MIM-1G.SHDSL moduleAttribute MIM-1G.SHDSL module Interface Cable MIM-1AMM/MIM-1AS MIM-1ASLPstn network Interface module MIM-1AMM LED Following table describes the LEDs on the panels MIM-1AE3 Module 25km, the interface will be unable to receive signalsInterface Optical Fiber Whereas MIM-1ASM/MIM-1ASL modules should be connected with Description of the LEDs on the MIM-1AE3 panel Following table describes the LEDs on the MIM-1AE3 panel MIM-1AT3 panel is shown in the following figure MIM-1AT3 ModuleFollowing table describes the LEDs on the MIM-1AT3 panel Interface attributes of MIM-1AT3 module Description of the LEDs on the MIM-1AT3 panel MIM-1POS Module Interface attributes of the MIM-1POS Following table describes the LEDs on the MIM-1POS panelDescription of the LEDs on the MIM-1POS panel MIM-1POS MIM-2FXS/MIM-2FXO/ MIM-2E&M and MIM-4FXS/MIM-4FXO/ MIM-4E&M MIM-2FXS/MIM-2FXO/MIM-2E&MMIM-4FXS/MIM-4FXO/MIM-4E&M MIM-2FXS panel Interface cable of FXS/FXO modules Interface cable of E&M modulesDescription of the LEDs on voice MIM panels RING0 RING1 TIP1 TIP0 Pinouts of E&M interface cable Bell V 4-wire MIM-HNDE module features Feature DescriptionMIM-HNDE Module MIM-2VE1 Module Troubleshooting MIM-2VE1 module is 1U in height, occupying two slots Following table describes the LEDs on the MIM-2VE1 panelInterface attributes of MIM-2VE1 Description of the LEDs on the MIM-2VE1 panel 75-ohm-to-120-ohm adapter with BNC connector VPM module is installed on the main board of MIM-2VT1 Voice signalsMIM-2VT1 Module Module as needed Following table describes the LEDs on the MIM-2VT1 panel MIM-2VT1 module is 1U in height, occupying two slotsDescription of the LEDs on the MIM-2VT1 panel Interface attributes of MIM-1VE1 MIM-1VE1 Module Following table describes the LEDs on the MIM-1VE1 panel MIM-1VE1 module is 1U in height, occupying two slotsDescription of the LEDs on the MIM-1VE1 panel Twisted pair cable, you can use network interface connector MIM-1VT1 Module VoIP systemInterface attributes of MIM-1VT1 Following table describes the LEDs on the MIM-1VT1 panel MIM-1VT1 module is 1U in height, occupying two slotsDescription of the LEDs on the MIM-1VT1 panel MIM-16FSW/MIM-16FSW-PoE/DMIM-24FSW/DMIM-24FSW-PoE Attribute OE module PoE module MIM-16FSW/MIM-16FSW-P DMIM-24FSW/DMIM-24FS LED status Description MIM-16FSW/MIM-16FSW-PoE panel Interface Cable MIM-IMA-4E1/MIM-IM Connecting Ethernet electrical cable8E1 Module Interface attributes of the MIM-IMA-4E1/ MIM-IMA-8E1 Attribute 75-ohm 120-ohm Description of the LEDs on the IMA-4E1/IMA-8E1 panel Cable 8T1 Module MIM-IMA-4T1/MIM-IMInterface attributes of MIM-IMA-4T1/MIM-IMA-8T1 MIM-IMA-4T1 MIM-IMA-8T1 MIM-IMA-8T1 panel MIM-2BSV/MIM-4BSV Interface attributes of MIM-2BSV/MIM-4BSVAttribute MIM-2BSV module MIM-4BSV module Description of the LEDs on the MIM-2BSV/MIM-4BSV panel Following figure illustrates the MIM-4BSV panel Crossover Isdn S/T cable MIM-1CPOS Module Interface attributes of the MIM-1CPOSE/MIM-1CPOST moduleMIM-1CPOSE/MIM-1CPOST There are many types of fiber-optic connectors, such as FC round fiber-optic connector with screw threadLEDs on the MIM-1CPOSE/MIM-1CPOST panel Optical Fiber MIM-1SHL-4W ModuleInterface attributes of the MIM-1SHL-4W MIM-1SHL-4W LEDs on the MIM-1SHL-4W panel Following table describes the LEDs on the MIM-1SHL-4W panel MIM-1SHL-4W and the other end to Dslam through Pstn XMIM-16FSW/XMIM-2 4FSWXMIM-24FSW support the following functions Auto-sensing at a rate of 10 Mbps or 100 Mbps Interfaces, which are usually used on hubs and LAN Switches Interface LEDs shows the XMIM-16FSW panelLEDs of the XMIM-16FSW/XMIM-24FSW FE port Ethernet cable Multifunctional Interface Modules FIC-1FE/FIC-2FE/FIC-4F FIC-1FE/FIC-2FE/FIC-4FE interface attributesFIC-1FE FIC-2FE FIC-4FE Following figure illustrates an FIC-2FE panel Following figure illustrates an FIC-4FE panelLEDs on the FIC-1FE/FIC-2FE/FIC-4FE panel Making Ethernet cables FIC-1GBE/FIC-2GBE Interface attributes of the FIC-1GBE/FIC-2GBE LEDs on the FIC-1GBE/FIC-2GBE panelFIC-1GBE FIC-2GBE FIC-1GEF/FIC-2GEF Interface attributes of the FIC-1GEF/FIC-2GEFFIC-1GEF FIC-2GEF LEDs on the FIC-1GEF/ FIC-2GEF panel FIC-1GEF panel FIC-2SAE/FIC-4SAE/FIC -8SAE DTE and DCE Interface attributes of the FIC-2SAE/FIC-4SAE/FIC-8SAE24 RS232 Max. transmission Baud rate bps Segment DTE DCE LEDs on the FIC-2SAE/FIC-4SAE panel Following figure shows the FIC-8SAE panel DCE cable RS449 DTE cable Introduction Functions FIC-8ASE/FIC-16ASE FIC-8ASE FIC-16ASE Interface attributes of the FIC-8ASE/ FIC-16ASE Low-End-and-Mid-Range Series Routers Cable Manual Dumb terminal cables, you can make on site by reference to Interface attributes of the FIC-E1 and FIC-E1-F cards Following figure illustrates the FIC-2E1 panel Following figure illustrates the FIC-1E1-F panel Following figure illustrates the FIC-4E1 panelFollowing figure illustrates the FIC-2E1-F panel Following figure illustrates the FIC-4E1-F panel E1 120-ohm balanced twisted-pair cable LEDs on the FIC-E1 and FIC-E1-F panels Interface cable of the FIC-4E1/FIC-4E1-F Addition, you are available with 75-ohm-to-120-ohm adapters FIC-4E1/FIC-4E1-F by default, they are not provided Addition, you are available with 75-ohm-to-120-ohm adaptersFIC-1E1/F Card IC-1E1-F FIC-2E1/FIC-2E1-F FIC-4E1/FIC-4E1-F Setting DIP switches on the FIC-E1/FIC-E1-F cards End Connecting the interface cable of the FIC-4E1/FIC-4E1-F FIC-8E1/FIC-8E1-FIntroduction FIC-8E1 FIC-8E1 120-ohm panel Interface attributes of the FIC-8E1/FIC-8E1-F card LEDs on the FIC-8E1/FIC-8E1-F panels FIC-1T1-F/FIC-2T1-F/FIC-4T1-F Following figure illustrates the FIC-2T1 panel Following figure illustrates the FIC-4T1 panelInterface attributes of the FIC-T1/FIC-T1-F cards Following figure illustrates the FIC-1T1-F panel Following figure illustrates the FIC-2T1-F panelFollowing figure illustrates the FIC-4T1-F panel LEDs on the FIC-T1 and FIC-T1-F panels FIC-8T1/FIC-8T1-F Introduction FIC-8T1LEDs on the FIC-8T1 and FIC-8T1-F panels LEDs on FIC-8T1 and FIC-8T1-F panels FIC-8T1 panel FIC-1CE3 Represent the demultiplex processFIC-1CE3 interface attributes LEDs on the FIC-1CE3 panel FIC-1CE3 panel FIC-1CT3 interface attributes FIC-1CT3 FIC-4BSE LEDs on the FIC-1CT3 panelInterface attributes of the FIC-4BSE Jumper settings of the FIC-4BSE example Set the jumpers on the FIC-4BSE LEDs on the FIC-4BSE panel FIC-4BSE panel Following table describes the LEDs on the FIC-1AE3 panel FIC-1AE3Interface attributes of the FIC-1AE3 FIC-1AE3 LEDs on the FIC-1AE3 panel FIC-1AT3 Interface attributes of the FIC-1AT3 Following table describes the LEDs on the FIC-1AT3 panelLEDs on the FIC-1AT3 panel FIC-1AT3 FIC-1AT3 and another end to the Tx port on another device FIC-1AT3 and another end to the Rx port on another deviceStatus Loopback Following figure illustrates the FIC-1ATM-OC3SML panel Following figure illustrates the FIC-1ATM-OC3SM panelInterface attributes of the ATM cards LEDs on the ATM card panels FIC-1G.SHDSL Interface attributes of the FIC-1G.SHDSLFIC-1G.SHDSL LEDs on the FIC-1G.SHDSL panel FIC-1POS Interface attributes of the FIC-1POS Following table describes the LEDs on the FIC-1POS panelLEDs on the FIC-1POS panel FIC-1POS 2E&M FIC-2FXS/FIC-2FXO/FICFIC-4FXS/FIC-4FXO/FIC 4E&M Following figure illustrates the FIC-2E&M panel Following figure illustrates the FIC-2FXO panelFollowing figure illustrates the FIC-4FXS panel FIC-2FXO/FIC-4FXO Following figure illustrates the FIC-4E&M panel Following figure illustrates the FIC-4FXO panelInterface cables for the FIC-FXS/FIC-FXO cards Interface cables for FIC-E&M cards PBX Router side Signal at switch side Bell RJ-45 Pin Wire Connecting the FIC-2E&M/FIC-4E&M card on site FIC-HNDESelf-made E&M interface cable by the router side Following table describes the LEDs on the FIC-HNDE panel Troubleshooting by reading the LED behaviorsInterface attributes of the FIC-HNDE LEDs on the FIC-HNDE Interface attributes of FIC-2VE1 FIC-2VE1 Description of the LEDs on FIC-2VE1 panel FIC-2VE1 panel Connecting the Interface Cable FIC-2VT1 Interface attributes of FIC-2VT1FIC-2VT1 panel is shown in the following figure Description of the LEDs on FIC-2VT1 panel Interface attributes of FIC-1VE1 FIC-1VE1FIC-1VE1 panel is shown in the following figure Description of the LEDs on FIC-1VE1 panel Description of the LEDs on FIC-1VE1 panel FIC-1VT1 VPM module is installed on the main board of FIC-1VT1 Description of the LEDs on FIC-1VT1 panel Interface attributes of FIC-1VT1 FIC-16FSW/FIC-16FSW- PoE/DFIC-24FSW/DFIC- 24FSW-PoE 16FSW-PoE Attribute Module DFIC-24FSW/DFIC-24FSW-PoE module FIC-16FSW/FIC FIC-16FSW/FIC-16FSW-PoE panel Interface Cable Interface attributes of the FIC-IMA-4E1/FIC-IMA-8E1 FIC-IMA-4E1/FIC-IMA-8FIC-IMA-4E1 FIC-IMA-8E1 LEDs on the FIC-IMA-4E1/FIC-IMA-8E1 panel 75-ohm FIC-IMA-4E1 panel 75-ohm 8E1 conversion cable FIC-IMA-4T1/FIC-IMA-8 Interface attributes of the FIC-IMA-4T1/FIC-IMA-8T1FIC-IMA-4T1 FIC-IMA-8T1 LEDs on the FIC-IMA-4T1/FIC-IMA-8T1 panel FIC-IMA-8T1 panel FIC-1SHL-4W Interface attributes of the FIC-1SHL-4WFIC-1SHL-4W Following table describes the LEDs on the FIC-1SHL-4W panel FIC-1CPOSFIC-1SHL-4W and the other end to Dslam through Pstn LEDs on the FIC-1SHL-4W panel FIC-1CPOSE/FIC-1CPOST Interface attributes of the FIC-1CPOSE/FIC-1CPOST LEDs on the FIC-1CPOSE/FIC-1CPOST panel Following figure illustrates the FIC-1CPOST panel FIC-2BSV/FIC-4BSV Interface attributes of the FIC-2BSV/FIC-4BSV Following figure illustrates the FIC-4BSV panelLEDs on the FIC-2BSV/FIC-4BSV panel FIC-2BSV FIC-4BSV Connecting the Interface Cable Following figure illustrates the FIC-24FXS panel FIC-24FXSInterface attributes of the FIC-24FXS card Description of LEDs on the FIC-24FXS panel FIC-24FXS conversion cable Following figure illustrates the DFIC-24FXO24FXS panel DFIC-24FXO24FXSInterface attributes of the DFIC-24FXO24FXS module Description of LEDs on the DFIC-24FXO24FXS panel DFIC-24FXO24FXS Flexible Interface Cards Following table describes the LEDs on the panel Ande ModuleRemoving Ande card Follow these steps to remove the Ande card Snde Module Installing Ande card Installing Snde card Installing/RemovingVcpm Module Snde Card Following table describes the LEDs on the main board Installing Vcpm cardRemoving Vcpm card Interface attributes of the Vcpm module Router installed with no RTV-SIC-1E1/T1 module Router installed with RTV-SIC-1E1/T1 module ESM/VCPM Module Supported and ⋅ means Not supported SIC/DSIC Purchase GuideSIC/DSIC options Interface card 20-20 20-40 50-40 Type 20-21 MIM/DMIM options MIM/DMIM Purchase Guide30-16 30-60 50-60 MIM-2FXS ⋅ MIM-4FXS ⋅ MIM-2FXO ⋅ MIM-4FXO ⋅ MIM-4BSE ⋅ MIM-1CPOSE ⋅ MIM-1CPOST ⋅ MIM-IMA-4T1 ⋅ MIM-IMA-8T1 ⋅MIM-1SHL-4W ⋅ MIM-2BSV ⋅ MIM-4BSV ⋅ FIC/DFIC Purchase Guide FIC/DFIC optionsFIC-1E1-F FIC-2E1-F FIC-4E1-F Purchase Guide ESM/VPM/VCPMFIC-1SHL-4W FIC-2BSV FIC-4BSV FIC-24FXS ESM-ANDE ESM-SNDE Vcpm VPM32 VPM24 VPM16 VPM8 ESM/VPM/VCPM options