3Com MSR 20, MSR 30, MSR 50 w, c

FIC-2FXS/FIC-2FXO/FIC-2E&M and FIC-4FXS/FIC-4FXO/FIC-4E&M 193

Step 2: Locate the Rx and Tx fiber-optic interfaces on the interface card. Use two

fibers to connect the FIC-1POS to another device: Rx to Tx and Tx to Rx.

Step 3: Power on the device and check the LINK LED on the FIC-1POS panel: ON

means the Rx link is present and OFF means the opposite. In the latter case, check

the line status.

wWARNING: Because invisible laser radiation may be emitted from the aperture of

an optical port when no fiber is connected or the dust cap is removed, do not

stare into the open aperture.

Replace the dust cap when no fiber is connected to the optical port.

FIC-2FXS/FIC-2FXO/FIC

-2E&M and

FIC-4FXS/FIC-4FXO/FIC

-4E&M

Introduction FIC-2FXS/FIC-4FXS, the 2-/4-port voice subscriber circuit interface card, processes

and transmits over data communications networks voice signals for 2/4 regular

analog phones, faxes, or AT0 loop trunks of telephone exchanges.

FIC-2FXO/FIC-4FXO, the 2-/4-port voice AT0 analog trunk interface card, processes

and transmits over data communications networks voice signals for 2/4 loops of

telephone exchanges.

FIC-2E&M/FIC-4E&M, the 2-/4-port voice E&M analog trunk interface card,

provides and transmits over data communications networks voice signals for 2/4

E&M analog trunks.

cCAUTION: When connecting the FIC-2FXS/FIC-2FXO/FIC-2E&M or the

FIC-4FXS/FIC-4FXO/FIC-4E&M, make sure your router has access to an IP network

or some other WAN.

Interface Attributes The following table describes the interface attributes of the

FIC-2FXS/FIC-2FXO/FIC-2E&M and the FIC-4FXS/FIC-4FXO/FIC-4E&M.

Table 139 Interface attributes of the FIC-2FXS/FIC-2FXO/FIC-2E&M and the

FIC-4FXS/FIC-4FXO/FIC-4E&M

Attribute Description

Connector RJ-45

Number of connectors 2 (FIC-2FXS/FIC-2FXO/FIC-2E&M)

4 (FIC-4FXS/FIC-4FXO/FIC-4E&M)

Cable Telephone cable with ferrite core

E&M trunk cable (only for E&M cards,

made on site)

Contents

Main 3Com Corporation 350 Campus Drive Marlborough, MA USA 01752-3064 C ABOUT THIS GUIDE 1 2 3 4 5 A Page ABOUT THIS GUIDE n w c n Related Documentation 1 SIC/DSIC Interface Cards MIM/DMIM/XMIM Page Page FIC/DFIC Interface Cards Page SIC/MIM/FIC Purchase Guideline n Installation/Removal of a SIC/MIM/FIC w Page c T roubleshooting Page 2 n SIC-1FEA n Page SIC-1SAE Interface LEDs SIC-1SAE panel is shown in the following figure: Figure 7 SIC-1SAE panel Description of the LEDs on SIC-1SAE panel is given in the following table: Table 3 Interface attributes of the SIC-1SAE Table 4 LEDs on SIC-1SAE panel Page Page w SIC-1EPRI/SIC-1E1-F Figure 18 Default setting of the DIP switches 8BIT description and settings of DIP switch are given in the following table: Table 5 Interface attributes of SIC-1EPRI/SIC-1E1-F Table 6 Description and settings of the internal DIP switch of SIC-ERRI/SIC-1E1-F Page n c SIC-1TPRI/SIC-1T1-F Interface LEDs SIC-1TPRI panel is shown in the following figure: Figure 25 SIC-1TPRI panel SIC-1T1-F panel is shown in the following figure: Figure 26 SIC-1T1-F panel The status description of the LEDs is given in the following table: c SIC-1AM/SIC-2AM c SIC-1FXS/SIC-1FXO & SIC-2FXS/SIC-2FXO c Interface LEDs SIC-1FXS/SIC-1FXO panel Figure 30 SIC-1FXS panel Figure 31 SIC-1FXO panel Figure 32 SIC-2FXS panel Figure 33 SIC-2FXO panel c SIC-4FSW/SIC-4FSW-Po E/DSIC-9FSW/DSIC-9FS W-PoE Page Page SIC-1GEC n Table 16 Interface Attributes of the SIC-1GEC Table 17 Attributes of SFP module Page c w SIC-1VE1 n Figure 39 Default setting of DIP switches Description of DIP switch settings is given in the following table: 75-ohm cable, flip BIT1-8 to ON, and when connecting 120-ohm cable, flip BIT1-8 to OFF. Table 21 Description of DIP switch settings of SIC-ERRI/SIC-1E1-F Page n c SIC-1VT1 n Interface LEDs The following figure illustrates the SIC-1VT1 panel. Figure 45 SIC-1VT1 panel The following table describes the LEDs on the SIC-1VT1 panel. Table 23 Interface Attributes of the SIC-1T1-F Table 24 Description on SIC-1VT1 LED SIC-1ADSL Page n SIC-1ADSL-I Page n SIC-1BS/SIC-2BS&SIC-1 BU/SIC-2BU Interface LEDs The following figures illustrate the SIC-1BS/SIC-2BS and SIC-1BU/SIC-2BU panels. c SIC-1BSV/SIC-2BSV Interface Attributes Interface LEDs The following figure illustrates the SIC-1BSV panel. The following table describes the LEDs on SIC-1BSV/SIC-2BSV panel. Figure 55 SIC-1BSV panel The following figure illustrates the SIC-2BSV panel. Page SIC-1FEF n SIC-8AS Page c w Page 3 M MIM-1FE/MIM-2FE/MI M-4FE Modules Page MIM-1GBE/MIM-2GBE Page MIM-1GEF/MIM-2GEF Interface LEDs MIM-1GEF panel is shown in the following figure: Figure 70 MIM-1GEF panel MIM-2GEF panel is shown in the following figure: Figure 71 MIM-2GEF panel The following table describes the LEDs on the MIM-1GEF/MIM-2GEF panel. n w MIM-2SAE/MIM-4SAE/ MIM-8SAE Module Interface LEDs MIM-2SAE panel is shown in the following figure: Table 43 Interface attributes of MIM-2SAE/MIM-4SAE/MIM-8SAE Page Page Page n w c MIM-8ASE/MIM-16AS E Module w c MIM-1E1/MIM-2E1/MI M-4E1/MIM-1E1-F/MI M-2E1-F/MIM-4E1-F Modules Page n Page c Page c Page MIM-8E1/MIM-8E1-F n Page MIM-1T1/MIM-2T1/MI M-4T1/MIM-1T1-F/MI M-2T1-F/MIM-4T1-F Modules Page Page c MIM-8T1/MIM-8T1-F n Page MIM-1CE3 Module n c MIM-1CT3 Module Page n MIM-4BSE Module Page Interface LEDs The following figure illustrates the MIM-4BSE panel. Table 61 Set the jumpers on the MIM-4BSE c MIM-1G.SHDSL n MIM-1AMM/MIM-1AS M/MIM-1ASL Interface LEDs MIM-1AMM/MIM-1ASM/MIM-1ASL module panels are shown in the following figures: Figure 117 MIM-1AMM panel The following table describes the LEDs on the panels: Figure 118 MIM-1ASM panel Figure 119 MIM-1ASL panel w n MIM-1AE3 Module n c MIM-1AT3 Module n c MIM-1POS Module Interface Attributes Interface LEDs The following figure illustrates the MIM-1POS panel: Figure 123 MIM-1POS panel The following table describes the LEDs on the MIM-1POS panel: Table 71 Interface attributes of the MIM-1POS w MIM-2FXS/MIM-2FXO/ MIM-2E&M and MIM-4FXS/MIM-4FXO/ MIM-4E&M c Interface LEDs Voice MIM panels are shown in the following figures: Page n MIM-HNDE Module MIM-2VE1 Module n Page MIM-2VT1 Module n c MIM-1VE1 Module Page n MIM-1VT1 Module n MIM-16FSW/MIM-16F SW-PoE/DMIM-24FSW /DMIM-24FSW-PoE Page DMIM-24FSW/DMIM-24FSW-PoE panel is shown in the following figure: The following tables describe the GE and SFP fiber interface LEDs: n MIM-IMA-4E1/MIM-IM A-8E1 Module Interface LEDs The following figures illustrate the MIM-IMA-4E1 and MIM-IMA-8E1 panels. Figure 148 MIM-IMA-4E1 (75-ohm) panel Figure 149 MIM-IMA-8E1 (75-ohm) panel Table 90 Interface attributes of the MIM-IMA-4E1/ MIM-IMA-8E1 Table 91 Description of the LEDs on the IMA-4E1/IMA-8E1 panel Page MIM-IMA-4T1/MIM-IM A-8T1 Module Page MIM-2BSV/MIM-4BSV Interface LEDs The following figure illustrates the MIM-2BSV panel. Figure 155 MIM-2BSV panel Figure 157 Straight-through ISDN S/T cable The following figure illustrates the MIM-4BSV panel. Figure 156 MIM-4BSV panel Page MIM-1CPOS Module c n MIM-1SHL-4W Module Page XMIM-16FSW/XMIM-2 4FSW n Page Page 4 FIC-1FE/FIC-2FE/FIC-4F E Page n c FIC-1GBE/FIC-2GBE Page FIC-1GEF/FIC-2GEF Interface LEDs The following figures illustrate the FIC-1GEF and FIC-2GEF panels: Figure 175 FIC-1GEF panel Figure 176 FIC-2GEF panel The following table describes the LEDs on the FIC-1GEF and FIC-2GEF panels. Table 106 Interface attributes of the FIC-1GEF/FIC-2GEF n w FIC-2SAE/FIC-4SAE/FIC -8SAE n Interface LEDs The following figures show the FIC-2SAE and FIC-4SAE panels: Figure 178 FIC-2SAE panel The following table describes the LEDs on the FIC-2SAE/ FIC-4SAE panel: Figure 179 FIC-4SAE panel Table 109 Interface attributes of the FIC-2SAE/FIC-4SAE/FIC-8SAE Page Page Page c FIC-8ASE/FIC-16ASE Page c FIC-1E1/FIC-2E1/FIC-4E 1 and FIC-1E1-F/FIC-2E1-F/FIC -4E1-F Page Page Page Page n Figure 204 Default setting of the DIP switches for the FIC-E1/FIC-E1-F cards The following table describes how to set a DIP switch on the FIC-E1/FIC-E1-F cards: c Table 115 Setting DIP switches on the FIC-E1/FIC-E1-F cards c FIC-8E1/FIC-8E1-F n Page FIC-1T1/FIC-2T1/FIC-4T 1 and FIC-1T1-F/FIC-2T1-F/FIC -4T1-F Interface LEDs The following figure illustrates the FIC-1T1 panel. Figure 211 FIC-1T1 panel The following figure illustrates the FIC-2T1 panel. Figure 212 FIC-2T1 panel The following figure illustrates the FIC-4T1 panel. Page c 176 CHAPTER 4: FLEXIBLE INTERFACE CARDS Figure 218 Extending a T1 cable FIC-8T1/FIC-8T1-F n Table 120 LEDs on the FIC-8T1 and FIC-8T1-F panels Page c FIC-1CE3 n c FIC-1CT3 n FIC-4BSE Page Interface LEDs The following figure illustrates the FIC-4BSE panel. Table 127 Set the jumpers on the FIC-4BSE c FIC-1AE3 n c FIC-1AT3 n c FIC-1ATM-OC3MM/FIC -1ATM-OC3SM/ FIC-1ATM-OC3SML n Interface LEDs The following figure illustrates the FIC-1ATM-OC3MM panel. Figure 230 FIC-1ATM-OC3MM panel The following table describes the LEDs on the card panels. The following figure illustrates the FIC-1ATM-OC3SM panel. Figure 231 FIC-1ATM-OC3SM panel w c FIC-1G.SHDSL FIC-1POS Interface LEDs The following figure illustrates the FIC-1POS panel: Figure 234 FIC-1POS panel Step 1: Insert the SFP card into its corresponding slot. The following table describes the LEDs on the FIC-1POS panel. Table 137 Interface attributes of the FIC-1POS w FIC-2FXS/FIC-2FXO/FIC -2E&M and FIC-4FXS/FIC-4FXO/FIC -4E&M c Interface LEDs The following figure illustrates the FIC-2FXS panel: The following figure illustrates the FIC-2FXO panel: The following figure illustrates the FIC-2E&M panel: The following figure illustrates the FIC-4FXS panel: n Page n FIC-HNDE Interface Features The following table describes the interface attributes of the FIC-HNDE. Panel and LEDs The following figure illustrates the FIC-HNDE panel: Figure 243 FIC-HNDE panel The following table describes the LEDs on the FIC-HNDE panel. Table 142 Interface attributes of the FIC-HNDE n module as needed. Interface Attributes The interface attributes of FIC-2VE1 are given in the following table. Interface LEDs FIC-2VE1 panel is shown in the following figure: Table 144 Troubleshooting by reading the LED behaviors Page Page FIC-2VT1 c FIC-1VE1 n Page FIC-1VT1 n Page FIC-16FSW/FIC-16FSW- PoE/DFIC-24FSW/DFIC- 24FSW-PoE Page Page n FIC-IMA-4E1/FIC-IMA-8 E1 Interface LEDs The following figures illustrate the FIC-IMA-4E1 and FIC-IMA-8E1 (75-ohm) panels: Figure 259 75-ohm FIC-IMA-4E1 panel Figure 260 75-ohm FIC-IMA-8E1 panel The following table describes the LEDs on the FIC-IMA-4E1/FIC-IMA-8E1 panel: Table 157 Interface attributes of the FIC-IMA-4E1/FIC-IMA-8E1 Page FIC-IMA-4T1/FIC-IMA-8 T1 Page FIC-1SHL-4W FIC-1CPOS c n FIC-2BSV/FIC-4BSV Page Page FIC-24FXS c DFIC-24FXO24FXS Page Page 5 ANDE Module SNDE Module VCPM Module Page c n Page A MODULE PURCHASE GUIDE n SIC/DSIC Purchase Guide MIM/DMIM Purchase Guide Page FIC/DFIC Purchase Guide ESM/VPM/VCPM Purchase Guide