Monitoring System Activity and Performance |
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
DS1 Errors |
|
| Armed Mode | Loop Attenuation | Insertion Loss |
| HDSL4 Errors | Alarm Type | BERT Status | ||||||||||||
|
|
|
|
|
| P |
|
| E |
| Log | I |
| Report | Rlogon |
| Help | ||||
| Monitor |
|
|
|
|
|
| ||||||||||||||
|
|
| BERT |
|
|
|
|
|
|
|
|
|
|
|
| Rate: |
| ||||
|
|
|
|
|
| LA | =16 |
| 17 | 16 |
| 17 |
| 16 | 16 |
|
|
| |||
|
|
|
|
|
| =17 |
|
|
|
| 17 | 17 |
|
|
| ||||||
|
| ARM |
|
| INSL=23 |
|
| 22 |
|
|
| 23 | 23 |
|
|
| |||||
|
| ESF |
| ES | =0 |
|
| 0 | 0 |
| 0 |
| 28 | 0 |
|
| ESF | ||||
|
|
| SES | =0 |
|
| 0 | 0 |
| 0 |
| 23 | 0 |
|
| ||||||
|
| B8ZS | >+ | UAS | =0 |
| LP1 | 0 | LP1 | 0 | + | 171 | 151 | + | B8ZS | ||||||
|
| + |
|
| + |
| LP1 |
|
| ||||||||||||
|
| TUC | = |
| ======== DU1 ============ DU2 ============ TUR |
| |||||||||||||||
|
|
|
|
| MAL |
| |||||||||||||||
|
| ESF | LPF |
|
|
|
|
|
| ESF | |||||||||||
< | B8ZS | ============ | ============ | ============ | B8ZS | ||||||||||||||||
|
| + | + |
| LP2 | + |
| LP2 | + | LP2 |
| + | |||||||||
- |
|
|
|
| M | =15 |
| 15 | 14 |
| 15 |
| 16 | 16 |
| ES | =0 | ||||
| ES |
|
|
|
|
| |||||||||||||||
| SES=0 |
| LA | =18 |
| 17 | 17 |
| 16 |
| 17 | 17 |
| SES=0 | |||||||
| UAS=56 |
| INSL=24 |
| 23 | 23 |
| 22 |
| 23 | 23 |
| UAS=0 | ||||||||
|
|
|
|
|
| ES | =0 |
|
| 0 | 0 |
| 0 |
| 2 | 2 |
| PRM=0 | |||
|
|
|
|
|
| SES | =0 |
|
|
| 0 |
| 0 |
| 1 | 0 |
|
|
| ||
|
|
|
|
|
| UAS | =0 |
|
|
| 0 |
| 0 |
| 0 | 0 |
|
|
| ||
Active Loopbacks | : | LOOPBACKS |
|
| |||||
|
|
|
|
| |||||
Press | to | select | LB |
|
| NLOC – Loopdown All Active Loopbacks |
| ||
and | to activate |
|
|
| (LPDN,NLOC,CREM,NREM,CLOC) |
| |||
ID: xxxx | xxxx |
| 12:30:01 | System: OK___ | |||||
Frame Code and Type | Active Loopback | Margin | System Status |
Figure 12. Monitor Screen - Active Loopback with Alarms
2To initiate a loopback, press the SPACEBAR to cycle through the loopback choices. Press ENTER to make your choice.
When prompted with the message: Are you sure (Y/N)?, press Y to initiate the loopback or N to cancel. For more information about loopbacks and troubleshooting, see “Testing” on page 42.
3To initiate a loopdown of all active loopbacks, press the SPACEBAR to select LPDN, then press ENTER . When prompted with the message: Are you sure (Y/N)?, press Y to initiate the loopdown or N to cancel.
| Table 8. Monitor Screen Descriptions |
|
|
Field | Description |
|
|
Active Loopback | An active loopback is indicated on the lower third of the Monitor screen. Available loopbacks are |
| indicated by gray text. See Table 16 on page 51 for a summary of the HDSL4 generic loopback |
| codes and activation methods. |
|
|
Alarm Type | Indicates type of alarm. |
MAL | Margin |
| set by the operator. |
|
|
Armed Mode | Indicates system is in an armed state for an intelligent repeater loopback command. |
|
|
BERT Status | Provides BERT Generator status, elapsed time, and BERT results. |
|
|
DS1 Errors |
|
ES Count | Errored |
| counts detected on the DS1 input over a |
| BPV, and ESF CRC errors. |
SES Count | Severely Errored |
| Severely Errored |
|
|
| Continued |
26 | September 12, 2003 |
