Tftpload, Tftpsave, Tsdump | ADTRAN IPR-S1000 instruction

Configuring the IPR-S1000

kernelcontents: Displays the firmware contents.

kernelstate: Displays the amount of firmware present on the Flash Card.

kernelswap: Allows to switch from the current firmware to the previous one.

packages: Displays the list of installed packages (software) and their version numbers.

reboot: Allows to restart the IPR-S1000.

tftpget: Allows to retrieve a kernel or a profile from the specified TFTP server.

tftpput: Allows to put a kernel or a profile on the specified TFTP server.

version: Displays two version numbers. The first one is the system version, and the second one is the version of the satellite reception’s software.

tftpload

Loads the last profile downloaded by TFTP.

tftpsave

Makes the current profile ready to TFTP upload.

traceroute + IP address or «Host» name

Prints the route that packets take to reach network host.

numeric: Prints hop addresses numerically rather than symbolically and numerically.

timeout: The process of traceroute will not exceed nsecond.

tos: Sets the type of service in probe packets to the following value (default zero). The value must be a decimal integer in the range 0 to 255.

verbose: Verbose output. Received ICMP packets other than TIME_EXCEEDED and UNREACHABLEs are listed.

wait: Sets the time (in seconds) to wait for a response to a probe (default 5 sec.).

tsdump

TS Dump is an MPEG2-TS (Transport Stream) monitoring tool. It can perform the following tasks:

-Display the selected (by PIDs) TS packets in different ways (hexa, hexdump style...).

-Record the selected TS packets into a file (using the browser or a FTP server).

-Display statistics of the selected PIDs.

display_dump_date: If selected, tsdump will display the start and end dates at the end of the dump.

display_pid_nbr: If selected, tsdump will display the PID number before each TS packet.

diplay_pid_rate: If selected, tsdump will display each PIDs bit rate at the end of the dump.

display_pkt_count: If selected, tsdump will display the number of TS packets received for each PID at the end of the dump.

81

Image 86

ADTRAN IPR-S1000 manual Tftpload, Tftpsave, Traceroute + IP address or «Host» name, Tsdump

Contents

USER’S Guide Acknowledgements Page Installing the IPR-S1000 Telnet interface Document organization Document objectivesAudience Document conventions Obtaining technical assistance Safety recommendationsTerms and abbreviations Material verification Ensure your safety Protect the equipment Installation checklistSite requirements Connecting to the satellite antenna Connecting the cablesConnecting to the Ethernet network Connecting the power cord Making the connection Making an initial configuration of the IPR-S1000Starting up the IPR-S1000 IP address FEC LNB Power Example 12.379 27500K + Auto 11.0dB OverviewBasic screens Example Ethernet 192.168.43.48/24 Menu Set configMain menu Example 1002 0x3ea 11KP10MB DVB 11C11D MAC filtering Example Frequency 12.3790000GHz ExampleHigh Band Low band Universal LNB Example Bauds Kbauds Example FEC Auto 1/2 2/3 3/4 4/5 5/6 6/7 7/8 8/9 PSK 16 QAM Example Polarization Vert./RHCP/14v Horiz./LHCP/18vExample Modulation Example Start MPE PID 1002 0x3ea Example LNB Power OffExample DVB IP address 172.022.000.051/24 Example Stop MPE PID 1002 0x3ea 3032 0xbd8 Example Processing CRC MPE Yes Ethernet Example MAC address filtering on 6 bytesEthernet IP address Media type Example IP address 192.168.043.048/24 13. IP Example Unicast forwarding Routing Bridging Example Broadcast bridging Yes New network address 000.000.000.000/00 Example Mcast forwarding Accept src addrMcast forwarding Yes routing Yes bridging Multicast On/Off Example Icmp redirect Yes DNS 1 DNS 2Example Bridging traffic Bridge only Analyse & bridge Example Delete all routes? CancelOk Example Def. none Edit Delete Profiles Profiles Save Fact. profile Tftp load Tftp saveExample Profile name Factory profile Startup Load Example Tftp Server addr Receipt code New write passwordNew read password Active MPE PID 1002 0x3 ea Menu View Config12.379 27500K + Auto 5.6dB DVB MAC address 00D0B5XXXXXX Monitoring Example Really reboot? ? Cancel Uncor. packets Reset ?Temperature 35.3 C Unlock Vber 1.3 E FirmwareQPSK S1000-3.01.41a Version Main Configuring the IPR-S1000 Configuring the IPR-S1000 Profiles and passwords Load Management System Reboot DVB Field, enter the low band local oscillator Interface Tuner Ethernet Definition This module allows you to manage IP parameters Forwarding User Interface Fixed Key Conditionnal Access Snmp Snmp traps Syslog Bandwidth IP Crypt Firewall Mac addresses NAT Drop-down menu, select active to start NAT PPP Configuring the IPR-S1000 Configuring the IPR-S1000 Pptp Configuring the IPR-S1000 Udlr Drop-down menu, select active to start Udlr Tools Spectrum TS Dump Configuring the IPR-S1000 DVB Dump IP Dump Configuring the IPR-S1000 Ethernet Ping You are trying to reach is actually operating Traceroute Blank field, enter the hostname or IP address Network statistics III The Telnet interface Shell Commands Example + name of the profile Bye Auth AuthenticationAbort Delete + name of the profile to be removed Get section.attribut GetdefaultExit Help Load + name of the profile LastprofileList Loadfactory Quit Ppp Point to point protocol Acts on PPP processPptp point to point tuneling protocol Rename + formername newname Traceroute + IP address or «Host» name TftploadTftpsave Tsdump Dvb Digital Video Broadcasting Get Displays NAT information System System action Traceroute + IP address or «host» name Dvb.bauds Sections and attributesBandwidth.size Dvb.fec Dvb.crcmpeDvb.dvbipaddr Dvb.freq Dvb.relaxbauds Dvb.mpepids List of MPE PIDs Dvb.mtuDvb.polar Dvb.scanfreq Ip.mcastaddr Ip.keepforusIp.macaddr Ip.multicast Nat.autoifaceiface Ppp.passwordNat.autoifaceactive Nat.dynactive Pptp.password Contains the password Pptp.pns Pptp.connecttimerPptp.keepalivetimer Pptp.retrytimer IV. The Snmp interface Glossary CRC DRO Iana ISO MPE Pstn RIP Vsat IPricotSA