Warnung | AMT Datasouth 4500 Series specs

WARNING

Any alteration or modification to this equipment may cause non-compliance to:

WARNUNG

Jede Abänderung oder Modifizierung dieses Geräts kann eine Zuwiderhandlung gegen folgende Bestimmungen darstellen:

ADVERTENCIA

Cualquier alteración o modificación de este equipo podría resultar en la infracción de:

ATTENTION

Tout changement ou modification apporté à cet équipement peut entraîner sa non conformité au:

•UL safety standard 1950, Third Edition

•CSA safety standard C22.2 No. 950

•FCC regulations for Class A Computing Devices

•EN50082

•EN60950

•EN55022, Class A

•EN61000-3-2

•EN61000-3-3

•EN60825-1

•Canadian ICES-003

iii

Image 3

AMT Datasouth 4500 Series manual Warnung

Contents

CodeWriter 4500 Series Operator’s Manual Page Warnung Warnung Adventercia Software Extended MaintenanceHardware Warranty Datasouth CodeWriter 4500 Disclaimer of Warranties Datasouth Table of Contents Contents Table of Figures CodeWriter 4500 Series Models Introduction CodeWriter 4505 Front/Side View External Media Feed Slot Operator Panel Document Exit Tear Bar CodeWriter 4500 Series Features Media Compatibility Features Guide to the Operator’s Manual This Page Intentionally Blank Unpacking and Power Up Equipment ChecklistQuick Start Guide Applying Power to the Printer Loading and Feeding Label Roll Media Loading Ribbon Take-Up Ribbon Supply Roll Ribbon Guide Bar Loading and Feeding the Ribbon CodeWriter 4500 Series Operator Panel Operator Panel Media Settings Set Label Parameters Without saving. Press the saving the changes Printer Model Print Speed 4505 100% 4505+ 4510 50% Set Print Parameters Feature/Settings Label Printing Test LabelsPrint Test Label Connecting the Printer Quick Start CDRunning the Quick Start CD Cable Connecting to a Personal ComputerConnecting the Cable Data Communications Mode COMx9600,n,8,1 Configuring the Personal ComputerSettings Control Panel Port Settings Value Bits per second Mode COMx9600,n,8,1 where x = the COM port number Sending Data to the PrinterType File.pal COMx Cable Examples Serial Port Specifications Series Printer DCE Modem DB25 Connector Hardware Flow Control Flow Control DSR Xon/Xoff Flow Control Setting RTS Polarity Operator Panel Settings for Data CommunicationsSetting the Baud Rate Setting the Flow Control Method Setting the Stop Bits Setting the DTR PolaritySetting the Parity Setting the Data Bits This Page Intentionally Blank Media Settings Setting the Document DimensionsDie-Cut Labels Notch or Hole Label Black Bar Labels Enter to save new defaults. Press Programming the Label Dimensions Pressing the settings Programming the Print Method Setting the Printing Method Print Speed and Darkness Setting the Print Parameters Speed Darkness Setting Print Speed and Darkness Adjusting Print Position Forward Distance Presentation Distance Bar Code Quality Bar Code OrientationPicket Fence Horizontal Bar Code Ladder Vertical Bar Code Bar Code Print Settings This Page Intentionally Blank Display and Panel Keys Operator Panel Reference Off-line Menu Reference 80% 100% Percentage of the printer’s Accessing this parameterParameter Values Description Print Speed % Printing Speed as a Label Parameters Config Revision are displayed Settings LabelSystem Params Firmware Part No Firmware part number System Parameters Default Parameter ValuesConfiguration Print Parameters Off-Line Menu Map Removing the Ribbon Take-up Roll Maintenance Printhead Cleaning Paper Path CleaningHeater Line Location Response to Display Messages Troubleshooting Guide Remove Ribbon Print or CANCEL? Media Feed Fault Print or CANCEL? Halt Ribbon Wrinkling Causing Poor Print Print Quality IssuesFirst Part of Label Content is Missing Sides or Top of Label Content is Missing Missing Dots in Label Data Communications Issues PC Reports Write Fault Error Writing to Device COMxHost System Does Not Report Errors, But Nothing Prints Controlling Hex Dump Mode Hex Dump Mode Adjusting the Gap Sensor Sensitivity Adjusting Sensor Sensitivity Printer is Displaying Media Feed Fault Message Adjusting the Black Bar Sensor Sensitivity Press the Pause key. This takes you to the off-line menu Adjusting the Ribbon Sensor Sensitivity Printer Displays Ribbon Out Message in Thermal Transfer Mode Verifying the Sensor Operation Key until the Enter to Select Diagnostics is displayed This Page Intentionally Blank Applications Overview Printer Application Language PALLabel Genesis Fonts PAL Fonts and Bar Codes Bar Codes Bar CodeEAN-13 EAN13 Codabar Postnet Maxicode MSI Plessy Establishing the Development Environment PAL Quick Start Undo Ctrl/U Function Keystroke Hex ValuePAL will display the line as it Has been typed so far Label Tutorial Hello World Label OutputPAL Command Sequence PAL Coordinate System Printing a Line Applications Overview Label Output World!Hello Hello World PAL Command Sequence Printing a Bar Code Label Output World Applications Guide Physical SpecificationsPower Input and Output Environmental Processing MediaSerial Communications Printing Flash Memory Management Advanced FeaturesHigh Speed Firmware Update Download Mode Auto-Baud Firmware Update Download Mode Release Identification Message Pause PAL Application Bootstrap Bypass Print Darkness Control Setting Contrast and PreheatKey until Enter to Select Expert Settings is displayed Enter to save new defaults . Press Advanced Features