![](/images/new-backgrounds/1300837/30083759x1.webp)
Installation
2.13 Connection of the "LED" remote indications unit
This unit is connected to connectors XR1 and XR2 of the remote relay boards of the
For the installation of the unit and details of connections at the unit end, see the instructions delivered with the unit nr 5102990400.
–recommended cable
2.14Connection of "Tele Monitor" remote control and indication unit (option)
This unit is connected by means of a signal loop connecting the XR10 connectors of the RAUZ 1 boards of the
–recommended cable
–consult manual 6739388XU for further information.
Connection of "Tele Monitor" remote control and indication unit
RAUZ 1 board | 1 |
| 10 |
|
|
|
|
|
|
|
|
| |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| XM098 | XM097 | XR11 |
|
|
|
|
| XM096 |
| XR10 | |||||||||||||
connector XR10 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
reception – |
|
|
|
|
|
| 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
| 3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
reception + |
|
|
|
|
| 4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
| 5 |
|
|
|
|
|
|
|
|
|
| to connector XR081 | |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
| 6 |
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
transmission – |
|
|
|
|
|
|
|
|
|
|
| 2 | on the COMZ board | ||||||||||||
|
|
|
|
| 7 |
|
|
|
|
| |||||||||||||||
|
|
|
|
|
|
|
|
| in the "Tele Monitor" unit | ||||||||||||||||
transmission + |
|
|
|
|
| 8 |
|
|
|
|
|
|
|
| 4 | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
| 9 |
|
|
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
| 10 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
9 7
to connector XR10
of another
Fig. 26
2.15 Final installation steps
After making the connections:
–install the front and rear base plates of the cubicles, clipping them to the feet of the cubicles (unless the connecting cables are fed through these openings);
–refit the terminal shields of the terminal blocks, switches and circuit breakers.