ATTO Technology 2500C operation manual

ATTO Technology, Inc.

ATT O

iPBridge

2500C/R/D

Installation and Operation Manual

respective holders. No part of this manual may be reproduced in any form or by any means without the

express written permission of ATTO Technology, Inc.

8/2005 Document Control Number: PRMA-0335-000

Contents

Main Page Page Contents 2.5 Additional configurations ....................................................19 3 ATTO ExpressNAV interface .............................................................21 3.1 ExpressNAV pages ..............................................................23 5 Copying iPBridge configurations .....................................................26 7 Alternative interface options ............................................................33 7.1.3 Maintenance commands ........................................41 7.1.4 Diagnostic commands ...........................................43 7.1.5 SCSI configuration commands .............................47 7.1.6 Serial port configuration commands ....................49 7.1.7 Ethernet commands ...............................................51 Page Page 1 iPBridge 2500 provide storage options iPBridge2500 features Possible storage configurations 1.1 ATTO iPBridge 2500R/D Installation instructions ATTO Technology Inc. iPBridge Installation and Operation Manual Front side with LEDs Back (connector) side 1.2 ATTO iPBridge 2500C Installation instructions Page 2 Configuring the iPBridge 10 Configuration: Ethernet 2.1 Getting an IP address 2.2 NDMP configuration provides backup Setting up NDMP 2.3 Mapping devices: NDMP Page 2.4 Mapping devices: iSCSI Single Target mode Multiple Target mode ATTO Technology Inc. iPBridge Installation and Operation Manual Exhibit 2.4-1 Examples of single and multiple target modes Mapping: single vs. multi target mode Page 2.5 Additional configurations Page 3 ATTO ExpressNAV interface 22 ATTO ExpressNAV Exhibit 3.0-1 An ExpressNAV page 23 3.1 ExpressNAV pages Serial Port Configuration Time & Date Configuration Ethernet Port Configuration SCSI Configuration Firmware Restart Help 25 4 Updating firmware PUT command from an FTP connection. The ATTO ExpressNAV method is preferred. Preliminary steps Using ATTO ExpressNAV Using FTP over GbE 5 Copying iPBridge configurations You can copy the configuration from one iPBridge to another in the field using the SEND and RECEIVE ZModem 6 Troubleshooting Inside out method Check the host event log Check the iPBridge event and trace logs Visually inspect LEDs Check for problems on attached devices Check the following in order to find problems on attached devices: enabled Check host versions Check the following to find problems on attached hosts: 29 Checking the serial port Checking the iPBridge internal configuration Checking iPBridge Ethernet ports Checking the iSCSI Host Adapter or NIC For a NIC using an OS iSCSI driver, continue to the iSCSI OS driver section. Checking the iSCSI OS driver Checking the Operating System Checking the applications Performance issues TraceLog If the host is not getting the performance it should, check the following items. Checking SCSI devices Checking iPBridge SCSI ports Checking the host system Checking the Operating System 7 Alternative interface options 34 Alternative interfaces Exhibit 7.0-1 Start up messages. 7.1 CLI provides ASCII-based interface 36 CLI 7.1.1 CLI commands summary Page 38 CLI Exhibit 7.1-2 The following error messages may be returned by the Command line Interface: 7.1.2 General use commands Page 41 7.1.3 Maintenance commands RestoreConfiguration default sets the password to its default value. Changes to the Admin Level user name require an Admin Level password. 43 7.1.4 Diagnostic commands ATTO iPBridge Page Page Page 47 7.1.5 SCSI configuration commands Page 49 7.1.6 Serial port configuration commands The ATTO iPBridge Page 51 7.1.7 Ethernet commands These commands configure the management and data Ethernet ports including telnet parameters. Changes to the Admin Level user name requires an Admin Level password. 53 7.1.8 NDMP commands Page 55 7.1.9 iSCSI commands Page 57 7.1.10 Mapping commands on page 13 and Mapping devices: iSCSI on page 15 for details. Page Appendix A ATTO iPBridge, FibreBridge family Page Appendix B Cabling SCSI cabling Ethernet connections v Appendix C Glossary ) , the Network Data Management Task Force More information is available through the Storage Networking Industry Association , and the IETF Page Appendix D Safety standards and compliances FCC Standards: Radio and Television Interference Canadian Standards European Standards Appendix E ATTO accessories iSCSI Bridge board-level models iSCSI Bridge desktop models & desktop models with rackmount kits NDMP Bridge models Cables Appendix F Warranty, contact information