Firmware, Restart, Help | ATTO Technology 2500C specs

A text field beneath the box lists the most recent commands issued to the iPBridge through this page.

If you enter an incorrect parameter, the CLI help text is displayed, showing the parameters available.

3If your entry was correct, type saveconfiguration

4Click the Submit button. Your changes are implemented.

Firmware

You may update firmware using ExpressNAV. Refer to

Updating firmware on page 25.

Restart

Implements a firmware restart of the bridge and makes permanent any changes you have made since the last firmware restart.

1 Click the Restart button.

A box tells you to wait until the counter gets to 0 and then the browser refreshes.

2If the browser does not refresh after the counter gets to 0, click the link to refresh it manually.

Note

Restarting the firmware may take a few minutes.

Help

Gives help information about the command line interface commands and troubleshooting tips via links to pages with help text for each category of options and one link to the Troubleshooting Tips and FAQs page on the ATTO website, www.attotech.com, or from the CD included with your iPBridge.

Contact information for ATTO technical support is on the right.

Help is always available by pressing any word shown in red on the screen.

Exhibit 3.1-1 CLI command entered incorrectly on the Advanced CLI page, error message with suggested solution, then correct entry with response.

24 ATTO ExpressNAV

Image 33

ATTO Technology 2500C operation manual Firmware, Restart, Help

Contents

Atto iPBridgeTM 2500C/R/D Page Page Contents Copying iPBridge configurations Additional configurationsTroubleshooting Atto ExpressNAV interface Maintenance commands Diagnostic commandsAlternative interface options Scsi configuration commands Serial port configuration commandsEthernet commands ISCSI commands Ndmp commandsMapping commands Appendix a Atto iPBridge, FibreBridge familyPage IPBridge2500 features IPBridge 2500 provide storage optionsIntelligent Bridging Architecture, the engine Connectivity, infrastructure solutions Possible storage Configurations Atto iPBridge 2500R/D LED indicators Installation instructionsExhibit 1.1-1 Atto iPBridge 2500R/D connector side Serial interface Back connector side Operating Temperature 0-70C external Atto iPBridge 2500CHeight of tallest component .535 inches Exhibit 1.2-1 Atto iPBridge 2500C faceplate Exhibit 1.2-2 Atto iPBridge 2500C board layout Microsoft iSCSI Initiator changes Configuring the iPBridge Click Launch Browser Getting an IP address How Ndmp works Ndmp configuration provides backup Setting up Ndmp ProcedureAssign Ndmp names to devices Map devices automatically Mapping devices NdmpMap devices manually Click AutoMap Configuration mapping Ndmp Single Target mode Mapping devices iSCSINode names Automatically configure Multiple Target mode Multiple Target modeManually configure Multiple Target mode Click on the Multi Target Mode enabled button Click Submit Exhibit 2.4-1 Examples of single and multiple target modes Mapping single vs. multi target mode Exhibit 2.4-2 Mapping with Atto ExpressNAV Change the current user name, password Additional configurationsCreate a read only password or user name Set the Real Time Clock Snmp protocol Configuring Scsi devices Atto ExpressNAV interface Accessing ExpressNAVBrowser compatibility To optimize ExpressNAV in Internet Explorer Exhibit 3.0-1 An ExpressNAV ExpressNAV pages Firmware RestartHelp Using FTP over GbE Using Atto ExpressNAVUpdating firmware Preliminary steps Using ZModem over the serial port Copying iPBridge configurationsZModem send clone.cln Send File/ZModem send Inside out method TroubleshootingCheck the host event log Check the iPBridge event and trace logs Check host versions Check for problems on attached devicesComponent check Checking Scsi devices Checking the serial port Checking the iPBridge internal configurationChecking iPBridge Ethernet ports Checking the LAN/WAN Checking the iSCSI OS driver Checking the iSCSI Host Adapter or NICChecking the Operating System Checking the applications Performance issues Checking iPBridge Scsi portsChecking Ethernet Host Adapter or NIC Checking the host system Use the serial port or header Alternative interface optionsUse Telnet Type iPBridge in the New Connection dialog box Atto Exhibit 7.0-1 Start up messages CLI provides ASCII-based interface Command conventions Symbol Indicates Command Defaults Example CLI commands summary Sntp 38 CLI General use commands VerboseMode Username Maintenance commands SNTPServer SpeedWriteDefaultSpeedWrite Time Diagnostic commands DumpTraceLog DumpEventLogEventLog EventLogFilter RouteDisplay PingSCSIPortList SCSITargets SNMPTrapAddress TemperatureSNMPTraps TailEventLog Scsi configuration commands VirtualDriveResponse Performance enhancement to newly-mapped Scsi devices Serial port configuration commands SerialPortBaudRateSerialPortEcho 50 CLI Ethernet commands 52 CLI NDMPAuthType Ndmp commandsNDMPMaxVersion NDMPPortNumber 54 CLI ISCSI commands ISNSLoginControl ISNSServerMultiTargetMode Mapping commands AutoMapRoute List to the map which satisfies a search for the given LUN Product features 2500C/R/D 2700C/R/D 1500E/D 1550E/D Appendix a Atto iPBridge, FibreBridge familyIPBridge products Fibre Bridge products Scsi cabling Appendix B CablingCable types Examples Ethernet connections Term Definition Appendix C Glossary Vi Appendix FCC Standards Radio and Television Interference Appendix D Safety standards and compliances European Standards Appendix E Atto accessories Contact Atto Technology, Inc Appendix F Warranty, contact information