Serial port configuration commands | ATTO Technology 2500C specs

7.1.6 Serial port configuration commands

The ATTO iPBridgeserial ports or serial headers are configured with default settings but may be customized to your specifications using the CLI commands in this section.

SerialPortBaudRate

Configures/reports the baud rate for the iPBridge RS-232 serial port or serial header. The number of data bits per character is fixed at 8 with no parity. Choices are 2400, 9600, 19200, 38400, 57600 and 115200.

Default: 115200

Set syntax: set SerialPortBaudRate [2400 9600 19200 38400 57600 115200]

Requires a SaveConfiguration command Get syntax: get SerialPortBaudRate

SerialPortEcho

Enables/disables/reports the echoing of keyboard input. When enabled, all non-control character keyboard input is output to the display. Local ASCII terminal (or terminal emulator) echo settings should be set to disabled while using SerialPortEcho enabled.

Default: enabled

Set syntax: set SerialPortEcho [enabled disabled] Requires a SaveConfiguration Restart command Get syntax: get SerialPortEcho

49

ATTO Technology Inc. iPBridge Installation and Operation Manual

Image 58

ATTO Technology 2500C operation manual Serial port configuration commands, SerialPortBaudRate, SerialPortEcho

Contents

Atto iPBridgeTM 2500C/R/D Page Page Contents Troubleshooting Additional configurationsCopying iPBridge configurations Atto ExpressNAV interface Diagnostic commands Maintenance commandsAlternative interface options Serial port configuration commands Scsi configuration commandsEthernet commands Mapping commands Ndmp commandsISCSI commands Appendix a Atto iPBridge, FibreBridge familyPage IPBridge 2500 provide storage options IPBridge2500 featuresIntelligent Bridging Architecture, the engine Possible storage Configurations Connectivity, infrastructure solutions Atto iPBridge 2500R/D Exhibit 1.1-1 Atto iPBridge 2500R/D connector side Installation instructionsLED indicators Serial interface Back connector side Atto iPBridge 2500C Operating Temperature 0-70C externalHeight of tallest component .535 inches Exhibit 1.2-1 Atto iPBridge 2500C faceplate Exhibit 1.2-2 Atto iPBridge 2500C board layout Configuring the iPBridge Microsoft iSCSI Initiator changes Getting an IP address Click Launch Browser Ndmp configuration provides backup How Ndmp works Procedure Setting up NdmpAssign Ndmp names to devices Map devices manually Mapping devices NdmpMap devices automatically Click AutoMap Configuration mapping Ndmp Mapping devices iSCSI Single Target modeNode names Manually configure Multiple Target mode Multiple Target modeAutomatically configure Multiple Target mode Click on the Multi Target Mode enabled button Click Submit Mapping single vs. multi target mode Exhibit 2.4-1 Examples of single and multiple target modes Exhibit 2.4-2 Mapping with Atto ExpressNAV Create a read only password or user name Additional configurationsChange the current user name, password Set the Real Time Clock Configuring Scsi devices Snmp protocol Browser compatibility Accessing ExpressNAVAtto ExpressNAV interface To optimize ExpressNAV in Internet Explorer Exhibit 3.0-1 An ExpressNAV ExpressNAV pages Restart FirmwareHelp Updating firmware Using Atto ExpressNAVUsing FTP over GbE Preliminary steps ZModem send clone.cln Copying iPBridge configurationsUsing ZModem over the serial port Send File/ZModem send Check the host event log TroubleshootingInside out method Check the iPBridge event and trace logs Component check Check for problems on attached devicesCheck host versions Checking Scsi devices Checking iPBridge Ethernet ports Checking the iPBridge internal configurationChecking the serial port Checking the LAN/WAN Checking the Operating System Checking the iSCSI Host Adapter or NICChecking the iSCSI OS driver Checking the applications Checking iPBridge Scsi ports Performance issuesChecking Ethernet Host Adapter or NIC Checking the host system Use Telnet Alternative interface optionsUse the serial port or header Type iPBridge in the New Connection dialog box Exhibit 7.0-1 Start up messages Atto Command conventions Symbol Indicates CLI provides ASCII-based interface CLI commands summary Command Defaults Example Sntp 38 CLI General use commands Username VerboseMode Maintenance commands SpeedWrite SpeedWriteDefaultSNTPServer Time Diagnostic commands EventLog DumpEventLogDumpTraceLog EventLogFilter SCSIPortList PingRouteDisplay SCSITargets SNMPTraps TemperatureSNMPTrapAddress TailEventLog Scsi configuration commands Performance enhancement to newly-mapped Scsi devices VirtualDriveResponse SerialPortBaudRate Serial port configuration commandsSerialPortEcho 50 CLI Ethernet commands 52 CLI NDMPMaxVersion Ndmp commandsNDMPAuthType NDMPPortNumber 54 CLI ISCSI commands ISNSServer ISNSLoginControlMultiTargetMode AutoMap Mapping commandsRoute List to the map which satisfies a search for the given LUN Appendix a Atto iPBridge, FibreBridge family Product features 2500C/R/D 2700C/R/D 1500E/D 1550E/DIPBridge products Fibre Bridge products Cable types Appendix B CablingScsi cabling Examples Ethernet connections Appendix C Glossary Term Definition Vi Appendix Appendix D Safety standards and compliances FCC Standards Radio and Television Interference European Standards Appendix E Atto accessories Appendix F Warranty, contact information Contact Atto Technology, Inc