ISNSLoginControl, ISNSServer | ATTO Technology 2500C manual

iSCSITargetNameDisplay

Displays the iSCSI target name. If Multiple Target mode is enabled, iSCSI target names are listed for all existing iSCSI targets.

Immediate command: iSCSITargetNameDisplay

iSNSLoginControl

Specifies whether the iPBridge delegates its access control/authorization to an iSNS server.

Default: disabled

Set syntax: set iSNSLoginControl [enabled disabled] Requires a SaveConfiguration command

Get syntax: get iSNSLoginControl

iSNSServer

Specifies whether the IP address of a valid iSNS server from which the iPBridge attempts iSCSI initiator discovery. Setting to 0.0.0.0 disables iSNS server lookup.

Default: 0.0.0.0

Set syntax: set iSNSServer [xxx.xxx.xxx.xxx] Requires a SaveConfiguration command Get syntax: get iSNSServer

MultiTargetMode

Enables/disables iSCSI multiple target mode addressing on the iPBridge. If enabled, all previous maps are deleted. In verbose mode, overwriting a map requires secondary confirmation of the action.

Set syntax: set MultiTargetMode [enabled disabled]

Get syntax: get MultiTargetMode

56 CLI

Image 65

ATTO Technology 2500C operation manual ISNSLoginControl, ISNSServer, MultiTargetMode

Contents

Atto iPBridgeTM 2500C/R/D Page Page Contents Copying iPBridge configurations Additional configurationsTroubleshooting Atto ExpressNAV interface Alternative interface options Maintenance commandsDiagnostic commands Ethernet commands Scsi configuration commandsSerial port configuration commands ISCSI commands Ndmp commandsMapping commands Appendix a Atto iPBridge, FibreBridge familyPage Intelligent Bridging Architecture, the engine IPBridge2500 featuresIPBridge 2500 provide storage options Connectivity, infrastructure solutions Possible storage Configurations Atto iPBridge 2500R/D LED indicators Installation instructionsExhibit 1.1-1 Atto iPBridge 2500R/D connector side Serial interface Back connector side Height of tallest component .535 inches Operating Temperature 0-70C externalAtto iPBridge 2500C Exhibit 1.2-1 Atto iPBridge 2500C faceplate Exhibit 1.2-2 Atto iPBridge 2500C board layout Microsoft iSCSI Initiator changes Configuring the iPBridge Click Launch Browser Getting an IP address How Ndmp works Ndmp configuration provides backup Assign Ndmp names to devices Setting up NdmpProcedure Map devices automatically Mapping devices NdmpMap devices manually Click AutoMap Configuration mapping Ndmp Node names Single Target modeMapping devices iSCSI Automatically configure Multiple Target mode Multiple Target modeManually configure Multiple Target mode Click on the Multi Target Mode enabled button Click Submit Exhibit 2.4-1 Examples of single and multiple target modes Mapping single vs. multi target mode Exhibit 2.4-2 Mapping with Atto ExpressNAV Change the current user name, password Additional configurationsCreate a read only password or user name Set the Real Time Clock Snmp protocol Configuring Scsi devices Atto ExpressNAV interface Accessing ExpressNAVBrowser compatibility To optimize ExpressNAV in Internet Explorer Exhibit 3.0-1 An ExpressNAV ExpressNAV pages Help FirmwareRestart Using FTP over GbE Using Atto ExpressNAVUpdating firmware Preliminary steps Using ZModem over the serial port Copying iPBridge configurationsZModem send clone.cln Send File/ZModem send Inside out method TroubleshootingCheck the host event log Check the iPBridge event and trace logs Check host versions Check for problems on attached devicesComponent check Checking Scsi devices Checking the serial port Checking the iPBridge internal configurationChecking iPBridge Ethernet ports Checking the LAN/WAN Checking the iSCSI OS driver Checking the iSCSI Host Adapter or NICChecking the Operating System Checking the applications Checking Ethernet Host Adapter or NIC Performance issuesChecking iPBridge Scsi ports Checking the host system Use the serial port or header Alternative interface optionsUse Telnet Type iPBridge in the New Connection dialog box Atto Exhibit 7.0-1 Start up messages CLI provides ASCII-based interface Command conventions Symbol Indicates Command Defaults Example CLI commands summary Sntp 38 CLI General use commands VerboseMode Username Maintenance commands SNTPServer SpeedWriteDefaultSpeedWrite Time Diagnostic commands DumpTraceLog DumpEventLogEventLog EventLogFilter RouteDisplay PingSCSIPortList SCSITargets SNMPTrapAddress TemperatureSNMPTraps TailEventLog Scsi configuration commands VirtualDriveResponse Performance enhancement to newly-mapped Scsi devices SerialPortEcho Serial port configuration commandsSerialPortBaudRate 50 CLI Ethernet commands 52 CLI NDMPAuthType Ndmp commandsNDMPMaxVersion NDMPPortNumber 54 CLI ISCSI commands MultiTargetMode ISNSLoginControlISNSServer Route Mapping commandsAutoMap List to the map which satisfies a search for the given LUN IPBridge products Product features 2500C/R/D 2700C/R/D 1500E/D 1550E/DAppendix a Atto iPBridge, FibreBridge family Fibre Bridge products Scsi cabling Appendix B CablingCable types Examples Ethernet connections Term Definition Appendix C Glossary Vi Appendix FCC Standards Radio and Television Interference Appendix D Safety standards and compliances European Standards Appendix E Atto accessories Contact Atto Technology, Inc Appendix F Warranty, contact information