Assigning Initial Router Parameters | Avaya P332G-ML instruction

Chapter 12 Avaya P330 Layer 3 Features

In order to...	Use the following command...


Use this command before	enable vlan commands
configuring VLAN-oriented
parameters, when there is more
than one interface on the same
VLAN

Display information about the IP	show ip route (Layer 3)
unicast routing table

Display information for an IP	show ip interface
interface

Display the status of ICMP error	show ip icmp
messages

Delete a Layer 2 Router interface	clear vlan

Assigning Initial Router Parameters

This section is only applicable if you either purchased a Layer 3 preconfigured P332G-ML module or purchased a Routing License Key Certificate for P332G-ML and activated the License Key. For information, on activating a Licence Key, see Obtaining and Activating a License Key below.

To configure the initial router parameters perform the following via the CLI:

1Enter set device-mode router and press Enter. You will be prompted to reset the module.

2Type y.

Wait for the module to restart and for the CLI prompt to reappear.

3Type show device-modeand press Enter to ensure that the module is in router mode.

Note: Assign the stack IP address as described in Assigning P330’s IP Stack Address before you assign the Initial Router IP address.

4To access Router commands from the Master module, type the command session <module number> router where <module number> is the location of the router module in the stack, and press Enter.

The command prompt changes from P330-N>to Router-N#>where N is the number of the router in the stack (see P330 Sessions).

5Type configure and press Enter. The prompt Router-N(configure)#appears.

Avaya P332G-ML User’s Guide

87

Image 101

Avaya P332G-ML manual Assigning Initial Router Parameters

Contents

Avaya P332G-ML Page Table of Contents Section Installing the P330 Section Configuration of the P330 LAG Bootp Section Troubleshooting and Maintaining the P330 Avaya P332G-ML User’s Guide Vii Table of Contents Viii Avaya P332G-ML User’s Guide Safety Information FCC Notice Before you InstallConventions Used in the Documentation CLI Conventions P332GAvaya P332G-ML User’s Guide Overview of the P330 Page About the P332G-ML Avaya P332G-ML OverviewIntroduction Command Line Interface CLI Layer 3 Features P330-MLAvaya P332G-ML Highlights Network Management and Monitoring Port Mirroring Avaya Multi-Service Network Manager MsnmFans, Power Supply and BUPS-ML Monitoring Avaya P332G-ML Overview Avaya P332G-ML User’s Guide Ietf Layer Standards and CompatibilityAvaya P330 Standards Supported Ietf Network Monitoring P332G-ML Switch SpecificationsPower Requirements Physical Safety AC Version SafetySafety DC Version EMC Emissions Interfaces Stacking Sub-moduleBasic Mtbf Table B.1 Stacking Sub-module Approved SFF/SFP Gbic Transceivers Safety InformationLaser Classification Usage Restriction Installing and Removing a SFF/SFP Gbic Transceiver InstallationSpecifications LX Transceiver Table B.2 Gigabit Fiber Optic Cabling Gigabit Fiber Optic CablingAgency Approval Console Pin Assignments Connector Pin Assignments Chapter Avaya P332G-ML User’s Guide Installing the P330 Page Required Tools InstallationSite Preparation Environmental Prerequisites Power Requirements DC Power Requirements AC P332G-ML Rack Mounting Rack Mounting Optional Connecting Stacked Switches Installing the X330STK-ML Stacking Sub-Module Optional Incorrect Stack Connection To connect stacked switches P330 Stack Connections Prerequisites Connecting Cables to Network EquipmentMaking Connections to Network Equipment ELX Powering On Avaya P330 Module DC Powering Up the Avaya P330Powering On Avaya P330 Module AC Post-Installation Avaya P332G-ML Front Panel Avaya P332G-ML Front and Rear Panels LED Name Description LED Status Full Duplex mode Always ON. All ports are full-duplex only LAG Avaya P332G-ML Back Panel BUPS-ML Input Connector Sticker BUPS-ML Input ConnectorPage Establishing a Serial Connection Configuring the Terminal Serial Port ParametersConnecting a Terminal to the Avaya P330 Serial port Assigning P330’s IP Stack Address P330 Sessions At the prompt, type Establishing a Telnet Connection Overview Connecting a Modem to the Console PortEstablishing a Modem PPP Connection with the P330 Security Levels User Authentication Exiting the Supervisor Level Entering the Supervisor LevelDefining new local users Introduction to Radius Entering the CLI Radius Authentication Procedure Radius Commands Allowed Managers Allowed Manager CLI Commands Configuration of the P330 Page Avaya P330 Default Settings Default Settings of the P330Configuring the Switch Default Settings of the P330 Chapter Default Settings of the P330 Default Settings of the P330 Avaya P332G-ML User’s Guide Basic Switch Configuration Operating parameters System Parameter ConfigurationIdentifying the system UTC Network Time Acquiring Protocols Parameter Configuration Basic Switch Configuration Avaya P332G-ML User’s Guide Ethernet Avaya P330 Layer 2 FeaturesOverview Configuring Ethernet Parameters MAC Address Flow ControlPriority CAM Table Ethernet Configuration CLI CommandsConfiguration CLI Commands for Ethernet Feature Ethernet Implementation in the Avaya P332G-ML Vlan Overview Vlan Configuration Multi Vlan Binding Vlan Tagging Illustrates these binding modes in P330 Ingress Vlan Security Automatic Vlan Learning Vlan CLI Commands Vlan CLI Commands Vlan Implementation in the Avaya P332G-ML Spanning Tree per Port Spanning Tree ProtocolSpanning Tree Protocol Port Roles Rapid Spanning Tree Protocol RstpAbout the 802.1w Standard Spanning Tree Implementation in the P330 Family Spanning Tree Protocol CLI Commandss Spanning Tree Protocol CLI Commands Spanning Tree Protocol CLI Commandss MAC Aging CLI Commands Configuring the P330 for MAC AgingMAC Aging CLI Commands MAC Aging LAG Overview LAG CLI CommandsLAG CLI Commands LAG Implementation in the Avaya P330 Family of Products Port Redundancy Operation Port Redundancy Intermodule Port Redundancy Port Redundancy CLI CommandsRedundancy CLI Commands check spec Avaya P330 Layer 2 Features IP Multicast Filtering IP Multicast Implementation in the Avaya P332G-ML IP Multicast CLI CommandsIP Multicast CLI Commands Implementation of Weighted Queuing in the P330-ML Weighted QueuingWeighted Queuing CLI Commands Weighted Queuing CLI Commands Weighted Queuing CLI Commands Stack Health CLI Command Stack Health CLI CommandsStack Health Implementation of Stack Health in the P330 Family Port Classification Port Classification CLI Commands Stack Redundancy Avaya P330 Layer 2 Features Avaya P332G-ML User’s Guide What is Routing? Avaya P330 Layer 3 Features Routing Multinetting Multiple Subnets per Vlan Routing ConfigurationForwarding IP Configuration CLI Commands IP Configuration Assigning Initial Router Parameters Obtaining and Activating a License Key Create the management/routing VLAN. Use the command Obtaining a Routing License Key Activating a Routing License Key License Key CLI Commands RIP Overview RIP Routing Interchange Protocol Configuration DIfferences Between RIP and RIP2 RIP CLI Commands Avaya P330 Layer 3 Features Ospf Overview Ospf Open Shortest Path First Configuration Ospf CLI Commands Static Routing Overview Static Routing Configuration Route Preferences Static Routing Configuration CLI Commands RIP Route Redistribution Route Redistribution Commands ARP Overview ARP Address Resolution Protocol Table Configuration ARP Table ARP CLI Commands DHCP/BOOTP Relay BOOTP/DHCP Overview BOOTP/DHCP CLI Commands NetBIOS Re-broadcast Configuration CLI Commands NetBIOS Re-broadcast ConfigurationNetBIOS Overview Vrrp Overview Vrrp Virtual Router Redundancy Protocol Configuration Case#1 Vrrp Configuration Example Case #2 Vrrp CLI Commands Avaya P332G-ML User’s Guide 109 Srrp Overview Srrp ConfigurationSrrp Configuration Example Srrp CLI Commands Policy Configuration Overview Policy Configuration Policy Configuration CLI Commands Avaya P330 Policy Policy Configuration Example P330-1super#ip access-list 100 2 fwd3 tcp any host IP Fragmentation/Reassembly CLI Commands IP Fragmentation and ReassemblyIP Fragmentation and Reassembly Overview Layer 3 Configuration File Avaya P330 Layer 3 Features 118 Avaya P332G-ML User’s Guide System Requirements Embedded Web Manager Embedded Web Manager/Browser Compatability Running the Embedded Web Manager Welcome Web-based Manager Install from your Local Web Site Installing the Java Plug-inInstall from the Avaya Site 124 Avaya P332G-ML User’s Guide P330 Page Power supply is not user-replaceable Troubleshooting the InstallationTroubleshooting the Installation Page Replacing the Stacking Sub-module Maintenance Chapter Maintenance 130 Avaya P332G-ML User’s Guide Obtain Software Online Downloading Software Updating the SoftwareSoftware Download Download New Version without Overwriting Existing Version United States How to Contact Us UAE AP Asia Pacific Region 136 Avaya P332G-ML User’s Guide