Plug board, Electronic | Avery ALS 230 specification

Operators Manual

ALS 230

2.3 Plug board

The plug board is shown in Figure 3. Beside the mains switch and the mains cable socket there are some more holes for optional functions. Standard execution in this machine is one I/O plug prepared for the product sensor. The connection of the other plugs is described in chapter Connections.

If you use the optional connections, it is strongly recommended to do this by means of the optional available SUB-D connectors. This ensures best EMI stability of the machine.

CAUTION! - The fuse holder setting you have to select according to your local main voltage (100, 120, 200 or 230 V). You carry this out by taking off the fuse holder and position the fuse holder insert accordingly.

APSF-Sensor

Product sensor

Applicator

PLC control

Figure 3 Plug board

2.4 Electronic

As standard the complete electronic is integrated in the machine. For special requirements (water protection e.g.) a machine version the electronic is housed in a separate cabinet is available.

Release 11/05

Page 15

Description

Image 17

Avery ALS 230 manual Plug board, Electronic

Contents

Page Page ALS Menu structure Errors and warnings Overview Important NotesManufacturer Copyright General Safety Notes Safety Operator’s duty of care Concrete security regulations and symbols used Security measures during normal operation Security measures during maintenance and repairs Observe environmental regulations Work on the electrical equipmentWork on pneumatic equipment Page Mechanics Description Dispensing mechanics Operator panel Operator panel ALS Electronic Plug board ALS General setting InstallationPreparing the machine Unpacking of the unit Define label data Prepare dispensingInsert material Capacitive label sensor Setting Lpit manuallyManual adjustment of the Cont parameter Capacitive sensor Label guide Fixed dispensing speed Adjust dispense functionStop position Product data bank Automatic dispensing speed ApsfLabel position on the product Operation Safety recommendation Left hand version Inserting label material 3Initialise new label material 4Control of dispense unit Function Display message Mains switchDispenser Menu selection Missing label function and web breaks Dispenser stopped OFF Dispenser active onMaterial initialisation Init Label positionPOS Label position Stop position Stod Dispense speed Velo Start delaySTADBlow on time Blow Product menu PD0n Maintenance Menu structure Configuration menuStandard menu Extended standard menu Standard menu Direct ConfigurationApplicator Extended menu Display Function Values Standard menuInitialisation Init Label position POS Start delay StadLabelling time Blow Dispensing speed Velo Display Function Data value Extended standard menu Sensor status Sens Label pitch LpitLabel contrast Product length Prdl Egra value check Stst Electronic gear ratio adjustment EgraSlew speed Slew Dwell time APT1 Time constant compensation APT4 Restart delay APT3Blow on time APT2 Printer dwell time PDT End of air stream signal AstpSave parameter in data bank Save Load data bank Load Product menu Release 11/05 Menu structure Possible adjustments ConfigurationCalling the configuration menu Possible tests Display Function of the parameter Possible data entry Handling the menu Menu functions Type of applicator Appl Automatic product speed followerAPSF Additional functions in the standard menu Input and sensor check ICHOutput check OCH Interface baud rate Baud Adjustment resettingFACTParity bit Pari Number of stop bits Sbit Recycle simulates max labels/min Recy Number of data bits DbitDistance sensor to dispensing edge Dist Label counter Labc Release 11/05 Configuration Data of the serial interface Serial interface Example Interface commandsCommand Description Range Ledg Error number Error message in display Error description Bit definition in error flagBit definition in warning flag Message in display Output signals Connections and signals Applicator modes Signals for direct dispense Timing ASA applicator Control signals for the ASA applicator APT2 Signals for the EP applicator Applicator connector Applicator connector Connecting NPN left or PNP right inputs Input signals Product sensor Example for connecting an NPN sensor Datalogic NPN connection of optional ODC sensor OD Control sensor Connection of a NPN type Apsf sensor Apsf sensor Optional connector for process contro Control signals Internal I/O connector Rule EMI Wiring diagram Electronic diagrams Layout dispenser electronic board Jumper position has to be 800 steps Page Dispenser error messages Errors and warningsSTO! Power-fail message Message Meaning How to solve Into Eeprom Dispenser warnings ALS Description Details Technical SpecificationTechnical Information APSF- Sensor Specification Optional function Application specification Labels per minute in relation to different label pitches Performance 375 125 875 625 ALS Page Function Factory Application Adjustment Function PD05 PD06 PD07 PD08 PD09 Function Factory PD01 PD02 PD03 PD04 Siehe Machine type Index