Operation, Safety recommendation | Avery ALS 230 manual

Operators Manual

ALS 230

4. Operation

This chapter describes the operation of the machine.

4.1 Safety recommendation

CAUTION!

y Before connections to the mains check the correct voltage selection.

yUse only original spare parts for service.

yOpen of the cover is only allowed authorised personal.

yHandling of the machine is permitted only trained personal.

yBe careful on operation, fingers, hair, clothes, jewellery, etc. may be caught by and get into rotating axles.

Release 11/05

Page 23

Operation

Image 25

Avery ALS 230 manual Operation, Safety recommendation

Contents

Page Page ALS Menu structure Errors and warnings Overview Important NotesManufacturer Copyright General Safety Notes Safety Operator’s duty of care Concrete security regulations and symbols used Security measures during normal operation Security measures during maintenance and repairs Work on pneumatic equipment Work on the electrical equipmentObserve environmental regulations Page Mechanics Description Dispensing mechanics Operator panel Operator panel ALS Electronic Plug board ALS General setting InstallationPreparing the machine Unpacking of the unit Insert material Prepare dispensingDefine label data Manual adjustment of the Cont parameter Setting Lpit manuallyCapacitive label sensor Capacitive sensor Label guide Stop position Adjust dispense functionFixed dispensing speed Label position on the product Automatic dispensing speed ApsfProduct data bank Operation Safety recommendation Left hand version Inserting label material 3Initialise new label material 4Control of dispense unit Function Display message Mains switchDispenser Menu selection Missing label function and web breaks Dispenser stopped OFF Dispenser active onMaterial initialisation Init Label positionPOS Label position Stop position Stod Dispense speed Velo Start delaySTADBlow on time Blow Product menu PD0n Maintenance Menu structure Configuration menuStandard menu Extended standard menu Standard menu Direct ConfigurationApplicator Extended menu Initialisation Init Standard menuDisplay Function Values Label position POS Start delay StadLabelling time Blow Dispensing speed Velo Display Function Data value Extended standard menu Label contrast Label pitch LpitSensor status Sens Product length Prdl Egra value check Stst Electronic gear ratio adjustment EgraSlew speed Slew Dwell time APT1 Blow on time APT2 Restart delay APT3Time constant compensation APT4 Printer dwell time PDT End of air stream signal AstpSave parameter in data bank Save Load data bank Load Product menu Release 11/05 Menu structure Possible adjustments ConfigurationCalling the configuration menu Possible tests Display Function of the parameter Possible data entry Handling the menu Menu functions Type of applicator Appl Automatic product speed followerAPSF Output check OCH Input and sensor check ICHAdditional functions in the standard menu Interface baud rate Baud Adjustment resettingFACTParity bit Pari Number of stop bits Sbit Recycle simulates max labels/min Recy Number of data bits DbitDistance sensor to dispensing edge Dist Label counter Labc Release 11/05 Configuration Data of the serial interface Serial interface Command Description Range Interface commandsExample Ledg Error number Error message in display Error description Bit definition in error flagBit definition in warning flag Message in display Output signals Connections and signals Applicator modes Signals for direct dispense Timing ASA applicator Control signals for the ASA applicator APT2 Signals for the EP applicator Applicator connector Applicator connector Connecting NPN left or PNP right inputs Input signals Product sensor Example for connecting an NPN sensor Datalogic NPN connection of optional ODC sensor OD Control sensor Connection of a NPN type Apsf sensor Apsf sensor Optional connector for process contro Control signals Internal I/O connector Rule EMI Wiring diagram Electronic diagrams Layout dispenser electronic board Jumper position has to be 800 steps Page Dispenser error messages Errors and warningsSTO! Power-fail message Message Meaning How to solve Into Eeprom Dispenser warnings ALS Technical Information Technical SpecificationDescription Details APSF- Sensor Specification Optional function Application specification Labels per minute in relation to different label pitches Performance 375 125 875 625 ALS Page Function Factory Application Adjustment Function PD05 PD06 PD07 PD08 PD09 Function Factory PD01 PD02 PD03 PD04 Siehe Machine type Index