Product menu | Avery ALS 230 specs

Operators Manual

ALS 230

5.3 Product menu

If parameters have to be changed because of different products and labels, the product menu can be used. The machine offers a data bank in which 14 sets of data can be stored.

If you want to switch to a particular product, select one of the product numbers by pressing NEXT or PRIOR and confirm with ENTER .The new parameters are valid now.

After switching to a new product bank the machine assumes the label roll has been changed or that a parameter such as STOD is different and so requires an initialisation of the label position at the dispensing edge. This is done by pressing the FEED key after loading a new product bank at which time the machine will move the first detected label edge to the dispense position.

Note: If the FEED key is not pressed after loading a new product bank the first detected label edge will be moved to the dispense position at the first signal from the product sensor!

Note: The function FACT available in the configuration menu clears all the product banks.

Release 11/05

Page 41

Menu structure

Image 43

Avery ALS 230 manual Product menu

Contents

Page Page ALS Menu structure Errors and warnings Copyright Important NotesOverview Manufacturer General Safety Notes Safety Operator’s duty of care Concrete security regulations and symbols used Security measures during normal operation Security measures during maintenance and repairs Work on pneumatic equipment Work on the electrical equipmentObserve environmental regulations Page Mechanics Description Dispensing mechanics Operator panel Operator panel ALS Electronic Plug board ALS Unpacking of the unit InstallationGeneral setting Preparing the machine Insert material Prepare dispensingDefine label data Manual adjustment of the Cont parameter Setting Lpit manuallyCapacitive label sensor Capacitive sensor Label guide Stop position Adjust dispense functionFixed dispensing speed Label position on the product Automatic dispensing speed ApsfProduct data bank Operation Safety recommendation Left hand version Inserting label material 3Initialise new label material Missing label function and web breaks Function Display message Mains switch4Control of dispense unit Dispenser Menu selection Label positionPOS Dispenser active onDispenser stopped OFF Material initialisation Init Label position Stop position Stod Product menu PD0n Start delaySTADDispense speed Velo Blow on time Blow Maintenance Extended standard menu Configuration menuMenu structure Standard menu Extended menu ConfigurationStandard menu Direct Applicator Initialisation Init Standard menuDisplay Function Values Dispensing speed Velo Start delay StadLabel position POS Labelling time Blow Display Function Data value Extended standard menu Label contrast Label pitch LpitSensor status Sens Product length Prdl Dwell time APT1 Electronic gear ratio adjustment EgraEgra value check Stst Slew speed Slew Blow on time APT2 Restart delay APT3Time constant compensation APT4 Load data bank Load End of air stream signal AstpPrinter dwell time PDT Save parameter in data bank Save Product menu Release 11/05 Menu structure Possible tests ConfigurationPossible adjustments Calling the configuration menu Display Function of the parameter Possible data entry Handling the menu Menu functions Type of applicator Appl Automatic product speed followerAPSF Output check OCH Input and sensor check ICHAdditional functions in the standard menu Number of stop bits Sbit Adjustment resettingFACTInterface baud rate Baud Parity bit Pari Label counter Labc Number of data bits DbitRecycle simulates max labels/min Recy Distance sensor to dispensing edge Dist Release 11/05 Configuration Data of the serial interface Serial interface Command Description Range Interface commandsExample Ledg Message in display Bit definition in error flagError number Error message in display Error description Bit definition in warning flag Output signals Connections and signals Applicator modes Signals for direct dispense Timing ASA applicator Control signals for the ASA applicator APT2 Signals for the EP applicator Applicator connector Applicator connector Connecting NPN left or PNP right inputs Input signals Product sensor Example for connecting an NPN sensor Datalogic NPN connection of optional ODC sensor OD Control sensor Connection of a NPN type Apsf sensor Apsf sensor Optional connector for process contro Control signals Internal I/O connector Rule EMI Wiring diagram Electronic diagrams Layout dispenser electronic board Jumper position has to be 800 steps Page Message Meaning How to solve Errors and warningsDispenser error messages STO! Power-fail message Into Eeprom Dispenser warnings ALS Technical Information Technical SpecificationDescription Details APSF- Sensor Specification Optional function Application specification Labels per minute in relation to different label pitches Performance 375 125 875 625 ALS Page Function Factory Application Adjustment Function PD05 PD06 PD07 PD08 PD09 Function Factory PD01 PD02 PD03 PD04 Siehe Machine type Index