Label position POS, Start delay Stad | Avery ALS 230 instruction

Operators Manual

ALS 230

Label position ____________________________________________________POS

Function: The start position POS defines when the labelling should take place, after the product has passed the product sensor. Changing the value for POS changes the applied label position on the product.

Only available if no applicator is used. Range: up to 999.9 mm in steps of 0.1 mm.

Start delay ______________________________________________________STAD

Function: Delay time for the dispensing after the product has passed the product sensor. This value influences the position of the label on the product.

Only available if an applicator is used. Range: 1 to 9999 ms

Stop position ___________________________________________________ STOD

Function: Stop position of the label once the label edge has reached the dispensing edge. The STOD value defines the actual stop position of the label in steps of 0.1 mm.

With this adjustment the label can be made to stop directly at the dispensing edge. To make the label stop after the dispensing edge the value of STOD should be adjusted accordingly.

ySelect the parameter STOD by pressing the keys FUNCTION.

yBy pressing the key ENTER the data input is activated. Range: 0.0 .... 200.0 (mm).

Labelling time___________________________________________________ BLOW

Function: The labelling time defines how long the applicator should blow the label onto the product.

Only available if an applicator is used. BLOW is identical with APT2 Range: 1 to 9999 ms

Dispensing speed ________________________________________________VELO

Function: This parameter defines the speed for the label material. Only available if no applicator

is used: With an automatic product speed sensor the actual speed is shown.

Range : 0.2 ... 30.0 m/min

Release 11/05

Page 34

Menu structure

Image 36

Avery ALS 230 manual Label position POS, Start delay Stad, Labelling time Blow, Dispensing speed Velo

Contents

Page Page ALS Menu structure Errors and warnings Important Notes OverviewManufacturer Copyright Safety General Safety Notes Operator’s duty of care Concrete security regulations and symbols used Security measures during maintenance and repairs Security measures during normal operation Work on the electrical equipment Work on pneumatic equipmentObserve environmental regulations Page Description Mechanics Dispensing mechanics Operator panel Operator panel ALS Plug board Electronic ALS Installation General settingPreparing the machine Unpacking of the unit Prepare dispensing Insert materialDefine label data Setting Lpit manually Manual adjustment of the Cont parameterCapacitive label sensor Label guide Capacitive sensor Adjust dispense function Stop positionFixed dispensing speed Automatic dispensing speed Apsf Label position on the productProduct data bank Safety recommendation Operation Inserting label material Left hand version 3Initialise new label material Function Display message Mains switch 4Control of dispense unitDispenser Menu selection Missing label function and web breaks Dispenser active on Dispenser stopped OFFMaterial initialisation Init Label positionPOS Stop position Stod Label position Start delaySTAD Dispense speed VeloBlow on time Blow Product menu PD0n Maintenance Configuration menu Menu structureStandard menu Extended standard menu Configuration Standard menu DirectApplicator Extended menu Standard menu Initialisation InitDisplay Function Values Start delay Stad Label position POSLabelling time Blow Dispensing speed Velo Extended standard menu Display Function Data value Label pitch Lpit Label contrastSensor status Sens Product length Prdl Electronic gear ratio adjustment Egra Egra value check StstSlew speed Slew Dwell time APT1 Restart delay APT3 Blow on time APT2Time constant compensation APT4 End of air stream signal Astp Printer dwell time PDTSave parameter in data bank Save Load data bank Load Product menu Release 11/05 Menu structure Configuration Possible adjustmentsCalling the configuration menu Possible tests Handling the menu Display Function of the parameter Possible data entry Menu functions Automatic product speed followerAPSF Type of applicator Appl Input and sensor check ICH Output check OCHAdditional functions in the standard menu Adjustment resettingFACT Interface baud rate BaudParity bit Pari Number of stop bits Sbit Number of data bits Dbit Recycle simulates max labels/min RecyDistance sensor to dispensing edge Dist Label counter Labc Release 11/05 Configuration Serial interface Data of the serial interface Interface commands Command Description RangeExample Ledg Bit definition in error flag Error number Error message in display Error descriptionBit definition in warning flag Message in display Connections and signals Output signals Signals for direct dispense Applicator modes Control signals for the ASA applicator Timing ASA applicator Signals for the EP applicator APT2 Applicator connector Applicator connector Input signals Connecting NPN left or PNP right inputs Example for connecting an NPN sensor Datalogic Product sensor OD Control sensor NPN connection of optional ODC sensor Apsf sensor Connection of a NPN type Apsf sensor Control signals Optional connector for process contro Internal I/O connector EMI Rule Electronic diagrams Wiring diagram Layout dispenser electronic board Jumper position has to be 800 steps Page Errors and warnings Dispenser error messagesSTO! Power-fail message Message Meaning How to solve Into Dispenser warnings Eeprom ALS Technical Specification Technical InformationDescription Details Application specification APSF- Sensor Specification Optional function Performance Labels per minute in relation to different label pitches 375 125 875 625 ALS Page Adjustment Function Factory Application Function Factory PD01 PD02 PD03 PD04 Function PD05 PD06 PD07 PD08 PD09 Index Siehe Machine type