Standard menu, Initialisation Init | Avery ALS 230 manual

Operators Manual

ALS 230

5.1 Standard menu

Usually this menu is used for labelling. All important parameters can be changed while the machine is running. After turning power on, the standard menu is active, unless the product menu was on before the machine was switched off.

If the product menu is active and you want to use the standard menu, switch off the machine again. Press the key NEXT FUNCTION while switching on the machine and the standard menu is active. In the standard menu you have access to all important parameters for labelling. The number of parameter and its kind depends on how the configuration has been made. Change of parameters is active immediately. Changed values are lost when turning off power. If values need to be stored, the extended standard menu has to be used. All available commands are listed down below.

Display	Function	Values
ON	Normal operation

OFF	Stop labelling operation

INIT	Initialisation of label sensor and label	After status of E__0 and E__1
	pitch detection	only

POS	Position of label on the product	Up to 999.9 mm

STOD	Stop position of label at the dispensing	0,0	..... 200,0 mm
	edge

VELO	Labelling speed	0.2	... 30.0 m/min

STAD	Delay time for labelling with applicator	1 ... 9999 ms

BLOW	apply time	0.1	... 999.9 ms

Initialisation ______________________________________________________ INIT

The function INIT is available only, if required for a new initialisation. Which is the case under the following circumstances:

a)Status error message E__0, the feed key was pressed with pressure roller open

b)Status E__1, while moving the label web no labels have been recognised over a web length of 4 labels.

c)During power on the FEED key was held depressed.

d)CONT or LPIT were changed to automatic mode.

Note: A new initialisation after an E__0 or E__1 message is not absolutely necessary if you sure that the label parameter are all right. Then leave the INIT display with the NEXT key and press only the key FEED to reposition the label at the dispensing edge.

Release 11/05

Page 33

Menu structure

Image 35

Avery ALS 230 manual Standard menu, Initialisation Init, Display Function Values

Contents

Page Page ALS Menu structure Errors and warnings Copyright Important NotesOverview Manufacturer General Safety Notes Safety Operator’s duty of care Concrete security regulations and symbols used Security measures during normal operation Security measures during maintenance and repairs Observe environmental regulations Work on the electrical equipmentWork on pneumatic equipment Page Mechanics Description Dispensing mechanics Operator panel Operator panel ALS Electronic Plug board ALS Unpacking of the unit InstallationGeneral setting Preparing the machine Define label data Prepare dispensingInsert material Capacitive label sensor Setting Lpit manuallyManual adjustment of the Cont parameter Capacitive sensor Label guide Fixed dispensing speed Adjust dispense functionStop position Product data bank Automatic dispensing speed ApsfLabel position on the product Operation Safety recommendation Left hand version Inserting label material 3Initialise new label material Missing label function and web breaks Function Display message Mains switch4Control of dispense unit Dispenser Menu selection Label positionPOS Dispenser active onDispenser stopped OFF Material initialisation Init Label position Stop position Stod Product menu PD0n Start delaySTADDispense speed Velo Blow on time Blow Maintenance Extended standard menu Configuration menuMenu structure Standard menu Extended menu ConfigurationStandard menu Direct Applicator Display Function Values Standard menuInitialisation Init Dispensing speed Velo Start delay StadLabel position POS Labelling time Blow Display Function Data value Extended standard menu Sensor status Sens Label pitch LpitLabel contrast Product length Prdl Dwell time APT1 Electronic gear ratio adjustment EgraEgra value check Stst Slew speed Slew Time constant compensation APT4 Restart delay APT3Blow on time APT2 Load data bank Load End of air stream signal AstpPrinter dwell time PDT Save parameter in data bank Save Product menu Release 11/05 Menu structure Possible tests ConfigurationPossible adjustments Calling the configuration menu Display Function of the parameter Possible data entry Handling the menu Menu functions Type of applicator Appl Automatic product speed followerAPSF Additional functions in the standard menu Input and sensor check ICHOutput check OCH Number of stop bits Sbit Adjustment resettingFACTInterface baud rate Baud Parity bit Pari Label counter Labc Number of data bits DbitRecycle simulates max labels/min Recy Distance sensor to dispensing edge Dist Release 11/05 Configuration Data of the serial interface Serial interface Example Interface commandsCommand Description Range Ledg Message in display Bit definition in error flagError number Error message in display Error description Bit definition in warning flag Output signals Connections and signals Applicator modes Signals for direct dispense Timing ASA applicator Control signals for the ASA applicator APT2 Signals for the EP applicator Applicator connector Applicator connector Connecting NPN left or PNP right inputs Input signals Product sensor Example for connecting an NPN sensor Datalogic NPN connection of optional ODC sensor OD Control sensor Connection of a NPN type Apsf sensor Apsf sensor Optional connector for process contro Control signals Internal I/O connector Rule EMI Wiring diagram Electronic diagrams Layout dispenser electronic board Jumper position has to be 800 steps Page Message Meaning How to solve Errors and warningsDispenser error messages STO! Power-fail message Into Eeprom Dispenser warnings ALS Description Details Technical SpecificationTechnical Information APSF- Sensor Specification Optional function Application specification Labels per minute in relation to different label pitches Performance 375 125 875 625 ALS Page Function Factory Application Adjustment Function PD05 PD06 PD07 PD08 PD09 Function Factory PD01 PD02 PD03 PD04 Siehe Machine type Index