Control signals | Avery ALS 230 instruction

Operators Manual

ALS 230

8.3.4Control signals

An optional connector could be installed for integration of the machine in the line control.

Inhibit +	Startunterdrückung +	5
+24 Volt	+24 Volt	9
Inhibit -	Startunterdrückung -	4
Error output	Fehlerausgang	8
Warning output	Warnausgang	3
Warning output	Warnausgang	7
Ready output	Betriebsbereitschaft	2
Ready output	Betriebsbereitschaft	6
Ground	Masse	1

5	white	weiß
9	red	rot
4	blue	blau
8	yellow	gelb
3	orange	orange
7	green	grün
2	violet	lila
6	brown	braun
1	black	schwarz

21

27

7

20

TBD 19 TBD 31 14

CN33

Figure 21 Optional connector for process contro

Release 11/05

Page 64

Connections and signals

Image 66

Avery ALS 230 manual Control signals, Optional connector for process contro

Contents

Page Page ALS Menu structure Errors and warnings Manufacturer Important NotesOverview Copyright Safety General Safety Notes Operator’s duty of care Concrete security regulations and symbols used Security measures during maintenance and repairs Security measures during normal operation Work on the electrical equipment Work on pneumatic equipmentObserve environmental regulations Page Description Mechanics Dispensing mechanics Operator panel Operator panel ALS Plug board Electronic ALS Preparing the machine InstallationGeneral setting Unpacking of the unit Prepare dispensing Insert materialDefine label data Setting Lpit manually Manual adjustment of the Cont parameterCapacitive label sensor Label guide Capacitive sensor Adjust dispense function Stop positionFixed dispensing speed Automatic dispensing speed Apsf Label position on the productProduct data bank Safety recommendation Operation Inserting label material Left hand version 3Initialise new label material Dispenser Menu selection Function Display message Mains switch4Control of dispense unit Missing label function and web breaks Material initialisation Init Dispenser active onDispenser stopped OFF Label positionPOS Stop position Stod Label position Blow on time Blow Start delaySTADDispense speed Velo Product menu PD0n Maintenance Standard menu Configuration menuMenu structure Extended standard menu Applicator ConfigurationStandard menu Direct Extended menu Standard menu Initialisation InitDisplay Function Values Labelling time Blow Start delay StadLabel position POS Dispensing speed Velo Extended standard menu Display Function Data value Label pitch Lpit Label contrastSensor status Sens Product length Prdl Slew speed Slew Electronic gear ratio adjustment EgraEgra value check Stst Dwell time APT1 Restart delay APT3 Blow on time APT2Time constant compensation APT4 Save parameter in data bank Save End of air stream signal AstpPrinter dwell time PDT Load data bank Load Product menu Release 11/05 Menu structure Calling the configuration menu ConfigurationPossible adjustments Possible tests Handling the menu Display Function of the parameter Possible data entry Menu functions Automatic product speed followerAPSF Type of applicator Appl Input and sensor check ICH Output check OCHAdditional functions in the standard menu Parity bit Pari Adjustment resettingFACTInterface baud rate Baud Number of stop bits Sbit Distance sensor to dispensing edge Dist Number of data bits DbitRecycle simulates max labels/min Recy Label counter Labc Release 11/05 Configuration Serial interface Data of the serial interface Interface commands Command Description RangeExample Ledg Bit definition in warning flag Bit definition in error flagError number Error message in display Error description Message in display Connections and signals Output signals Signals for direct dispense Applicator modes Control signals for the ASA applicator Timing ASA applicator Signals for the EP applicator APT2 Applicator connector Applicator connector Input signals Connecting NPN left or PNP right inputs Example for connecting an NPN sensor Datalogic Product sensor OD Control sensor NPN connection of optional ODC sensor Apsf sensor Connection of a NPN type Apsf sensor Control signals Optional connector for process contro Internal I/O connector EMI Rule Electronic diagrams Wiring diagram Layout dispenser electronic board Jumper position has to be 800 steps Page STO! Power-fail message Errors and warningsDispenser error messages Message Meaning How to solve Into Dispenser warnings Eeprom ALS Technical Specification Technical InformationDescription Details Application specification APSF- Sensor Specification Optional function Performance Labels per minute in relation to different label pitches 375 125 875 625 ALS Page Adjustment Function Factory Application Function Factory PD01 PD02 PD03 PD04 Function PD05 PD06 PD07 PD08 PD09 Index Siehe Machine type